The ace20 description has incorrect number of SSP instances
described. Correct number should be 3.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
The ace15 description has incorrect number of SSP instances
described. Correct number should be 3.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
The tgph description has incorrect number of SSP instances
described. Correct number should be 3.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
FTM internal counter can be clocked by one of three clock sources
independent of the module bus clock. This patch introduces a DT property
to perform the clock selection from DT.
DT sources are updated to keep the current clock selection for all boards,
with exception of ucans32k1sic board which is migrated to use system
clock by default, as this seems to be a better choice for most cases.
Some PWM LED samples require slower clock so overlays are added for
those cases.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Set RTC clock source to the internal 32 KHz LPO. Currently RTC clock is
used to source RTC counter and FTM counter.
Fixes#71289
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add support for half-duplex (3-wire) SPI operation using the Raspberry
Pi Pico PIO. To allow control of the size of the driver, including
half-duplex support is optional, under the control of Kconfig options.
The original PIO source code is also included as a reference.
Corrected 3-wire tx/rx counts.
Enable half-duplex code based on DTS configuration
Replace runtime checks with static BUILD_ASSERT()
Remove too-fussy Kconfig options
Removed PIO source per review request
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Convert all of the NXP SOCs with ENET to use the new
binding scheme, which is used by the new driver.
Convert any boards using this SOC to the new scheme as well,
and remove from the documentation the bit about the experimental
nature of the new driver and the overlay that shall no longer exist.
Some of the boards I do not have the hardware of, so apologies
if something breaks, as I have no way to know. All the boards
were made sure to at least build.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The MAC address macros are ridiculous in this driver.
Rewrite to be simpler and use eth.h common function.
Also, clarify the mac address generation on the DT overlays.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Adds a DAC driver for Texas Instruments DACx0501 family of devices
Signed-off-by: Eran Gal <erang@google.com>
Co-authored-by: Martin Jäger <17674105+martinjaeger@users.noreply.github.com>
Add a VEVIF node to be used for communicating with SysCtrl (cpusys).
This is the only part of the SysCtrl VPR exposed to local domains.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Enable MIPI mode to be set via devicetree, for displays that support
multiple MIPI DBI modes. This commit also adds new helpers for displays
that allow drivers to initialize the entire MIPI DBI configuration
structure from devicetree
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit updates the SRAM configuration in the STM32L475 device tree:
- `sram0` size reduced from 128K to 96K.
- `sram1` added with 32K.
These changes correct memory settings to prevent initialization failures.
Signed-off-by: Tianshuang Ke <qinyun575@gmail.com>
Nuvoton NPCX chips have reset registers which allow to reset the
peripheral hardware modules. This commit adds the support by
implementing the reset driver. Note that only the reset_line_toggle API
is supported because of the nature of the reset controller's design.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
If I2C3 switches from GPH1/GPH2 to GPB2/GPB5, extend setting
is required.
Test: Accessing I2C is normal if I2C2, I2C3, I2C5 are switched.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Copy the DMA channel information to both UART and SPI
instances of the Flexcomm as only one of them can be
active.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Enable serial interface on i.MX8ULP.
This also includes a SHA update for hal_nxp which
pulls in the following commits relevant to Zephyr:
* 3366f234ed47 build: hal_nxp: add TPM counter support
* 6544455fcf46 Compile in PXP driver if LVGL is set to use
PXP.
* 31463a848bcd devices: MIMX8UD7: add definition for
LPUART_RX_TX_IRQS
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Currently, all devices are initialized at boot time (following their
level and priority order). This patch introduces deferred
initialization: by setting the property `zephyr,deferred-init` on a
device on the devicetree, Zephyr will not initialized the device.
To initialize such devices, one has to call `device_init()`.
Deferred initialization is done by grouping all deferred devices on a
different ELF section. In this way, there's no need to consume more
memory to keep track of deferred devices. When `device_init()` is
called, Zephyr will scan the deferred devices section and call the
initialization function for the matching device. As this scanning is
done only during deferred device initialization, its cost should be
bearable.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
CSS was deprecated from the mcu-sdk. Removing driver from lpc55s36
to clear build error.
This is a temporary patch to remove the build error.
Fixes#69961
Signed-off-by: David Leach <david.leach@nxp.com>
Configure the 'soft-off' power state for manual selection only in the
DTS for Intel ADSP ACE 1.5 MTPM and ACE 2.0 LNL platforms.
Changes include:
- Setting 'min-residency-us' to 0 to indicate that the 'soft-off' state
is not intended for automatic selection by the power management
policy.
- Adding a 'status' property set to "disabled" to prevent the power
management policy from using this state during its decision process.
The 'soft-off' state remains available for manual selection by calling
`pm_state_force`. This change ensures that the state can still be used
when explicitly requested by the system or application, providing
flexibility for power management operations.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Implement a sensor for the output diagnostics of the power train
switch TLE9104.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This commit enables pinctrl on i.MX8ULP. This includes:
1) Adding `pinctrl_soc.h` header file.
2) Adding DTS node for IOMUXC1, which is one of the
IPs responsible for managing the 8ULP pads.
3) Adding .dtsi with pin definitions. For now, only
the LPUART7 pads are added to this file because this
is going to be the only consummer for now.
4) Modifying the `pinctrl_imx.c` driver to work for 8ULP.
5) Enabling the `CONFIG_HAS_MCUX_IOMUXC`, which is a
dependency of `CONFIG_PINCTRL_IMX`.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add definitions of PWM peripheral instances so it can be utilized
on nRF54H20 and nRF54L15 devices.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add binding for sitronix ST7796s, a MIPI DBI display controller
supporting up to 320x480 displays at 18 BPP
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The SparkFun Pro Micro header pins are numbered D1, D0, GND, ... from top
left whereas the SparkFun Pro Micro RP2040 and the Adafruit KB2040 boards
are using gpio 0, 1, GND, ... , so the pro_micro: connector gpio-map of
these boards should reflect that.
Graphical Datasheet for SparkFun Pro Micro RP2040:
https://cdn.sparkfun.com/assets/e/2/7/6/b/ProMicroRP2040_Graphical_Datasheet.pdf
Graphical Datasheet for SparkFun Pro Micro:
https://cdn.sparkfun.com/assets/f/d/8/0/d/ProMicro16MHzv2.pdf
Pinout of the Adafruit KB2040:
https://learn.adafruit.com/assets/106984
Please note that the KB2040 uses CircuitPython pin labels D0, D1 which does
not seemt correspond to the Arduino labels D0 and D1 used by the Pro Micro.
Signed-off-by: Daniel Irekvist <ulmanyar@gmail.com>
Add devicetree binding for NXP LCDIC. This controller is capable of
driving displays in 8080 or SPI 3/4 wire mode, and optionally swapping
endianness of display data as it sends it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add EDMA channels for LPUART RX and TX to LPFLEXCOMM 2 and 4, as these
nodes are enabled with the UART driver
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The initial version of an input driver for Cirque Pinnacle ASIC supports:
* Setting sensitivity
* Choosing between relative and absolute modes
* Relative mode
* Primary tap
* Swapping X and Y
* Absolute mode
* Setting number of idle packets
* Clipping coordinates outside of active range
* Scaling coordinates
* Inverting X and Y coordinates
Signed-off-by: Ilia Kharin <akscram@gmail.com>
For now DSI settings are hard-coded for the specific
LCD module used on the STM32H747I Discovery board
Signed-off-by: Erik Andersson <erian747@gmail.com>
To support the NT35510 display, some additional
options needs to be configurable in the STM32
DSI peripheral
Signed-off-by: Erik Andersson <erian747@gmail.com>
Add support for performing pinctrl operations. For now,
the only supported operation is applying the pinctrl default
state. Pinctrl is left optional to allow for scenarios in which
this is not required (e.g: AMP system in which another
OS configures the pinctrl).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add a property to select the push-pull GPIO output type to drive the
I2C recovery. The default is open-drain.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Enable clock control for i.MX8ULP. This consists of:
1) Adding a PCC node in the DTS
2) Adding a header file containing the definitions
of the clocks used by the peripherals to be enabled.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Enable sleep mode on LPC55S69 (corresponding to zephyr's runtime idle
mode). Add DT description and power api implementations.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Based on the iis2dlpc driver, with some significant differences in
interrupt handling.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Add common gpio node to pinctrl node (interrupts are shared between ports)
and syscon for interrupt edge detection register in order to support
interrupts in rzt2m gpio
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
Add irqs to rzt2m gpio bindings in order to add interrupt support to rzt2m
gpio driver and adds common gpio node to store interrupt config (irqs are
shared between ports)
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
Remove the unused "tx-delay-comp-offset" property from the base CAN FD
controller devicetree binding.
Having a static Transmitter Delay Compensation (TDC) offset is useless.
The offset needs to match the data phase timing parameters in order to
properly configure the second sample point when transmitting CAN FD frames
with BRS enabled.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove ethernet-fixed-link binding as it is redundant with the
phy bindings. Clearly, ethernet does not work without the L1
layer, which is a phy device, or an integrated mac/phy device,
and all of these things should be described properly in DT.
The schema did not even come with a compatible, meaning nodelabels
were hardcoded into the drivers, which is unacceptable.
- Remove the binding file for ethernet-fixed-link.yaml.
- Remove fixed link functionality from the nxp s32 gmac driver.
Since this functionality is already covered by the phy support,
it is redundant.
- Remove fixed link include from the s32 gmac binding.
- Remove fixed link include from the nuvoton numaker binding.
As far as I can tell the corresonding driver does not even
use it anyways, and I did not find any board with this device
that describes a "fixed link".
- Move the definition into the nxp,kinetis-ethernet binding
as the eth_mcux driver, which is already being deprecated,
does use this, contain the debt to the legacy driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Added configuration of long press reset functionality.
Includes ship/hibernate to wake debounce time and
disabled/one_button/two_button mode selection.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
The DHT20 sensor is a temperature and humidity sensor that uses I2C to
communicate with a microcontroller. The DHT20 sensor is Aosong.
use standard crc
update description to add reference to AHT20 and AM2301B
clean code, use defines and bit manipulation
add dht20 to i2c test suite for build tests
update bit manipulation
use more defines instead of raw numbers
add bindings to allow aht20 or am2301b to be used in devicetree
in all 3 cases, the same dht20.c driver is compiled
Signed-off-by: Nathan Olff <nathan@kickmaker.net>
1. Update EDMA driver for version 4
2. The DMAMux module is not always present. Use the
feature define to make this optional.
3. Use the EDMA_SetChannelMux API for SoC's that supports
this feature.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add enum for `constant-charge-voltage-max-microvolt` property to
signalize improper values given with device tree at compile time.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Maximum charging current is selected with an external resistor in
the MAX20335 charger. Therefore it is not possible to configure it
with software directly. There is only a capability to limit current
set with hardware but configuration of the limiter is not
straight-forward.
To reflect real functionality, drop usage of
`constant-charge-current-max-microamp` property as an required one and
use custom `chgin-to-sys-current-limit-microamp` instead.
Use enum in binding file to signalize improper values at compile time.
Drop support for `CHARGER_PROP_CONSTANT_CHARGE_CURRENT_UA` API property
since this cannot be handled.
The `max20335_get_constant_charge_current()` function become useless so
remove it.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Rework the data scaling algorithm for the "deadzone" mode so that the
deadzone is subtracted from the input rather than from the output. This
makes the whole output range usable rather than making the output jump
from the center value to the minimum deadzone range.
This changes the calibration data structure as well so now all values
refer to the input data, which is more coherent.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Byte value written to the device's
ERXFCON: ETHERNET RECEIVE FILTER CONTROL REGISTER
Sets the devices receive packet filter, optional. If not set
in device tree previous hard coded value`0xA3` is used.
Uni, multi and broadcast packets with valid CRC are accepted.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
This will update host dma copy aligmnet as with current
high value in some cases it was not possible to fully
empty the buffer
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
