Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Based on the iis2dlpc driver, with some significant differences in
interrupt handling.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Add irqs to rzt2m gpio bindings in order to add interrupt support to rzt2m
gpio driver and adds common gpio node to store interrupt config (irqs are
shared between ports)
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
Remove the unused "tx-delay-comp-offset" property from the base CAN FD
controller devicetree binding.
Having a static Transmitter Delay Compensation (TDC) offset is useless.
The offset needs to match the data phase timing parameters in order to
properly configure the second sample point when transmitting CAN FD frames
with BRS enabled.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove ethernet-fixed-link binding as it is redundant with the
phy bindings. Clearly, ethernet does not work without the L1
layer, which is a phy device, or an integrated mac/phy device,
and all of these things should be described properly in DT.
The schema did not even come with a compatible, meaning nodelabels
were hardcoded into the drivers, which is unacceptable.
- Remove the binding file for ethernet-fixed-link.yaml.
- Remove fixed link functionality from the nxp s32 gmac driver.
Since this functionality is already covered by the phy support,
it is redundant.
- Remove fixed link include from the s32 gmac binding.
- Remove fixed link include from the nuvoton numaker binding.
As far as I can tell the corresonding driver does not even
use it anyways, and I did not find any board with this device
that describes a "fixed link".
- Move the definition into the nxp,kinetis-ethernet binding
as the eth_mcux driver, which is already being deprecated,
does use this, contain the debt to the legacy driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Added configuration of long press reset functionality.
Includes ship/hibernate to wake debounce time and
disabled/one_button/two_button mode selection.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
The DHT20 sensor is a temperature and humidity sensor that uses I2C to
communicate with a microcontroller. The DHT20 sensor is Aosong.
use standard crc
update description to add reference to AHT20 and AM2301B
clean code, use defines and bit manipulation
add dht20 to i2c test suite for build tests
update bit manipulation
use more defines instead of raw numbers
add bindings to allow aht20 or am2301b to be used in devicetree
in all 3 cases, the same dht20.c driver is compiled
Signed-off-by: Nathan Olff <nathan@kickmaker.net>
1. Update EDMA driver for version 4
2. The DMAMux module is not always present. Use the
feature define to make this optional.
3. Use the EDMA_SetChannelMux API for SoC's that supports
this feature.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add enum for `constant-charge-voltage-max-microvolt` property to
signalize improper values given with device tree at compile time.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Maximum charging current is selected with an external resistor in
the MAX20335 charger. Therefore it is not possible to configure it
with software directly. There is only a capability to limit current
set with hardware but configuration of the limiter is not
straight-forward.
To reflect real functionality, drop usage of
`constant-charge-current-max-microamp` property as an required one and
use custom `chgin-to-sys-current-limit-microamp` instead.
Use enum in binding file to signalize improper values at compile time.
Drop support for `CHARGER_PROP_CONSTANT_CHARGE_CURRENT_UA` API property
since this cannot be handled.
The `max20335_get_constant_charge_current()` function become useless so
remove it.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Rework the data scaling algorithm for the "deadzone" mode so that the
deadzone is subtracted from the input rather than from the output. This
makes the whole output range usable rather than making the output jump
from the center value to the minimum deadzone range.
This changes the calibration data structure as well so now all values
refer to the input data, which is more coherent.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Byte value written to the device's
ERXFCON: ETHERNET RECEIVE FILTER CONTROL REGISTER
Sets the devices receive packet filter, optional. If not set
in device tree previous hard coded value`0xA3` is used.
Uni, multi and broadcast packets with valid CRC are accepted.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
MODEM_UBX: Adds Support for UBX Messages in Modem Subsystem.
GNSS API Supported: get_supported_systems, set_fix_rate, get_fix_rate,
set_enabled_systems, get_enabled_systems, set_navigation_mode,
get_navigation_mode.
Boards Tested: MIMXRT1062_FMURT6, VMU_RT1170.
Note: Partial support for U-BLOX Messages is provided as of now.
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Signed-off-by: Mayank Mahajan <mayankmahajan.x@nxp.com>
The STTS22H is an ultralow-power, high-accuracy, digital temperature
sensor offering high performance over the entire operating temperature
range. This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/resource/en/datasheet/stts22h.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add ability to set a wakeup counter in case OS Timer is
disabled in certain low power modes. Also add code to
compensate the tick value.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Enables usage Bluetooth LE GATT as a serial endpoint to exchange data
using UART APIs. This implementation is compatible with UART Interrupt
Driven APIs and uses the nus-uart device-tree node properties to
configure FIFO buffers for transmitting and receiving. Defining
multiple instances of the driver is possible and it allows implementing
multiple GATT NUS service instances to exchange data as separate serial
endpoints.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
"RW pinctrl" is clearly SOC specific naming for an IP
that is not necessarily constrained to live on one SOC series.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Split up the driver for the PWM controller MAX31790
into a multi function device driver.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Some SAI instances are mutliline, meaning they can have multiple
TX/RX data lines (channels). Depending on the board, the index
of the TX/RX data lines that are connected to the consumer
(e.g: the codec) may not always be 0. This commit fixes this
issue by adding support for passing the index of the used
TX/RX data lines through the DTS.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Make the properties for setting the initial sample points for both the
classic/arbitration phase and the data phase optional.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Implement a sensor for the output diagnostics of the low side
switch BD8LB600FS.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
