The FLASH_SIMULATOR already defaults to 'y' with proper
dependencies in its main definition in drivers/flash/Kconfig.
Let's not define it also in the board Kconfig.defconfig
as that causes dependencies to be lost if not duplicated
correctly.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Switch the default MCUBoot FW Update mode from Swap & Scratch
to more preferable Swap & Move for the rest of NXP boards.
Delete the scratch partition. Save RAM & ROM.
Slot 0 has one additional sector, for use with
the swap move algorithm.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Enable serial communication through UART port between HDMI ports.
Signed-off-by: Myeonghyeon Park <myeonghyeon@tsnlab.com>
Signed-off-by: Junho Lee <junho@tsnlab.com>
Add support for Raspberry Pi 5.
Currently only internal GPIO(gio_aon) is supported.
'Blinky' is the only sample that is working for now.
Signed-off-by: Junho Lee <junho@tsnlab.com>
Add support for the Waveshare ESP32-S3-Touch-LCD-1.28 board, including
support the LCD and touchscreen controllers. Tested with samples
already available.
Signed-off-by: Joel Guittet <joelguittet@gmail.com>
The MEMC driver in memc_mcux_flexspi.c is initialized
before the FlexSPI driver (flash_mcux_flexspi_nor.c)
and hangs during FlexSPI init. Initialize the FlexSPI
clock to 50MHz before the speed is set to the optimum
speed by the FlexSPI driver.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add PHYTEC's phyBOARD-Electra kit with the phyCORE-AM64x
System on Module (SOM).
This board only supports the M4F core, UART and GPIO right now,
since other drivers are still missing.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Configure SDMMC port on stm32h573i_dk.
Disable SDMMC clock check as using 48MHz is not strictly required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Added DTS of PDK's mx25r64 flash memory.
Memory is described under spi00 peripheral and
can be controlled used flash spi_nor driver.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Updated the frdm_mcxn947 with support for the
CTimer counter.
Signed-off-by: William Tang <william.tang@nxp.com>
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
After moving to HWMv2 em_starterkit_emsk_em11d_defconfig file was omitted.
Some of tests for the emks_em11d platform became broken.
This PR fixes https://github.com/zephyrproject-rtos/zephyr/issues/71753
Signed-off-by: Nikolay Agishev <agishev@synopsys.com>
There are several esp32-based boards that its conf and overlay
files are missing proper renaming to match cpu cluster.
This also removes all _SOC_ name from files.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
The STM32L152C-DISCOVERY is a development board based on the STM32L152RC
MCU. It is very similar to the stm32l1_disco, which was used as a
reference for the pinmux and defconfig.
stm32l152c_disco board has 256 Kbytes of flash memory, 32 Kbytes of RAM
and 8 Kbytes of data EEPROM.
Signed-off-by: Maxin John <maxin.john@gmail.com>
Fixes warnings when building documentation due to additional SoC
names being part of the Kconfig symbols which they should not be
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
UBSAN reports a bogus error in this function:
"load of address x with insufficient space for an
object of type '<unknown> *'"
as it seems unable to determine the size of
test_installers.
Let's disable this check in this function.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
`board.cmake` specified runner arguments only for the RAM-based variant,
use SOC config to support both:
`CONFIG_BOARD_NRF54L15PDK_NRF54L15_CPUFLPR` and
`CONFIG_BOARD_NRF54L15PDK_NRF54L15_CPUFLPR_XIP`.
Also align ARM target so it looks nice.
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
This patch is to fix issue #71473.
The commit 0be0d2175b revert some change
introduced by hwmv2 which allows defconfig can be overlay, so revert
back defconfig to be full configure files which includes all items used
by the board variants.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
FTM internal counter can be clocked by one of three clock sources
independent of the module bus clock. This patch introduces a DT property
to perform the clock selection from DT.
DT sources are updated to keep the current clock selection for all boards,
with exception of ucans32k1sic board which is migrated to use system
clock by default, as this seems to be a better choice for most cases.
Some PWM LED samples require slower clock so overlays are added for
those cases.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add default configuration related to BLE protocol,
for Application and Radio core on nRF54h20 platform.
Signed-off-by: Kamil Gawor <Kamil.Gawor@nordicsemi.no>
Convert all of the NXP SOCs with ENET to use the new
binding scheme, which is used by the new driver.
Convert any boards using this SOC to the new scheme as well,
and remove from the documentation the bit about the experimental
nature of the new driver and the overlay that shall no longer exist.
Some of the boards I do not have the hardware of, so apologies
if something breaks, as I have no way to know. All the boards
were made sure to at least build.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The MAC address macros are ridiculous in this driver.
Rewrite to be simpler and use eth.h common function.
Also, clarify the mac address generation on the DT overlays.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
"zephyr,sdmmc-disk" compatible stands for binding with sdmmc subsys which
is not compatible and not used with current STM32 sdmmc driver.
Declaring this compatible is a no op on STM32, so remove it.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Change IPC backend between Application and Radio core
to icbmsg which is more future proof than legacy
icmsg_me backend.
Signed-off-by: Kamil Gawor <Kamil.Gawor@nordicsemi.no>
Add the default `zephyr,ipc-icmsg` nodes for communication with
Application and Radiocore.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
The PHYTEC phyboard_lyra_am62x board was renamed to phyboard_lyra
to simplify the board name.
The PHYTEC phycore_am62x board was renamed and moved into
phyboard_lyra as phyboard_lyra/am6234/a53.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Both phyBOARD-Lyra AM62x boards were called
phyboard_lyra_am62x/am6234/a53 or phyboard_lyra_am62x/am6234/m4.
Since the AM62x SOC part number is now included in the board name
as am6234, there is no need to have am62x in the board name itself.
Moreover, PHYTEC also has an AM62Ax SOM which comes with the same
carrier-board. Integration of this kit would be easier later.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
phyBOARD-Lyra AM62x is the official name for our kit, which we
use to develop our reference software. This kit includes the
phyCORE-AM62x with TI's AM62x SoC.
Rename the phycore_am62x_am6234_a53 board to phyboard_lyra_am62x_am6234_a53
and move all code into the phyboard_lyra_am62x directory. Thereby, the
A53 and M4 boards are located in the same directory and both named
correctly.
This is also a good chance to update documentation for both cores and
use links to our latest BSPs as well as our official AM62x Yocto machine
name for the AM62x HS-FS SOM.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Enable serial interface on i.MX8ULP.
This also includes a SHA update for hal_nxp which
pulls in the following commits relevant to Zephyr:
* 3366f234ed47 build: hal_nxp: add TPM counter support
* 6544455fcf46 Compile in PXP driver if LVGL is set to use
PXP.
* 31463a848bcd devices: MIMX8UD7: add definition for
LPUART_RX_TX_IRQS
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
