Restructure the Bosch M_CAN driver backend to use per-instance Message RAM
configuration.
This removes the need for a common, artificial "can" devicetree node for
SoCs with multiple Bosch M_CAN-based CAN controllers and allows for
per-instance configuration of the number of e.g. standard (11-bit) and
extended (29-bit) filter elements.
As part of the restructure, software handling of CAN filter flags was moved
from per-flags bitfields to per-filter bitfields, solving an issue when
using more than 32 standard (11-bit) filter elements or more than 16
extended (29-bit) filter elements.
Fixes: #42030, #53417
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN devicetree binding to use a bosch,mram-cfg property
for specifying the memory layout of the Bosch M_CAN Message RAM. This is
identical to the Linux kernel devicetree binding for Bosch M_CAN IP core
based CAN controllers.
This introduces an offset cell which can be used for controllers with
shared Message RAM between Bosch M_CAN instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The BG95 pin configuration does not internally ever use the reset pin.
Because of this, there is no need to make reset pin mandatory.
Commit removes reset pin dependency [e.g. in case of BG95].
Signed-off-by: Andrei Hutanu <andrei.hutanu.i@gmail.com>
Add a property to the ADC channels which allows the configuration
of the current source pin.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Added Input/Output trigger mux address's as properties
that can be passed into the DMA driver. This is intended
to send INPUTMUX signals into the DMA.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Ports the Jinghua Display JHD1313 LCD (with RGB backlight) driver
to use the new auxdisplay driver interface. This driver is used on
the seeed grove LCD RGB display, and replaces it.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
Removed few VIF properties which are being hardcoded
Updated the script to parse source VIF XML and add information to
the output
Added optional Kconfig option to configure custom source VIF XML path
Cleaned up the code
Signed-off-by: Madhurima Paruchuri <mparuchuri@google.com>
Added intel LPSS DMA interface using dw common to support
usage of internal DMA in LPSS UART, SPI and I2C for
transfer and receive operations.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The OpenTitan power manager is responsible for changing the OpenTitan's
operation to and from low power state. This patch adds a simple binding
for the power manager's config registers.
This is part of the OpenTitan watchdog patch series. The power manager
HWIP block needs to be configured to enable the watchdog reset
functionality in the OpenTitan Verilator simulation.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
The OpenTitan AON Timer is a hardware device that has two features:
the wakeup timer and watchdog timer. This commit series implements the
watchdog feature.
The spec can be found here:
https://opentitan.org/book/hw/ip/aon_timer/index.html
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
This adds support for the USB interface for the
Renesas Smartbond DA1469x device family.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
Add an API-less MFD driver for nPM6001. In this case, the MFD device
driver doesn't expose any API as plain I2C API is used within other
device drivers (regulator, GPIO, watchdog). This driver just initializes
some device properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
include the infineon,cat1-scb.yaml for I2c and UART bindings to convey
that they are using SCB (Serial Control Block)
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Add a new regulator driver for Analog Devices ADP5360. While it is a MFD
device, only support for BUCK/BUCKBOOST regulators is added in this
patch.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add VREF+ sensor driver and DT node definition.
This driver allows determining the actual voltage applied to an SoC's
VREF+ pin, by comparing the VREFINT internal bandgap voltage reference
with its factory calibration data.
In packages where VREF+ is bonded to VDDA, this permits direct measurement
of VDDA voltage.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Introduce DesignWare ARC Data Fusion IP Subsystem(DFSS) SPI
driver for ARC boards, i.e. EMSDP, which uses DW SPI to controll
SPI-Flash and DFSS SPI to connect external devices. Both drivers
share most source code, but DFSS uses ARC auxiliary registers.
Move FIFO depth setting to device tree.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
Renesas Renesas SmartBond(tm) have two ADC blocks:
GPADC and SDADC.
This change adds drivers for both.
Each ADC supports only one channel setup, drivers allow
to have multiply channels in sequence. Switching
between ADC sources in done in software.
GPADC has 10 bit resolution (accuracy can be increase
with oversampling). Values up to 3.6V can be measured
on selected pins. V30 and VBAT1 can also be measured.
SDADC has 14 bit resolution and can take measurements
from 8 pins (single of differential) and VBAT.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Since Merge zephyrproject-rtos#57360, user can use ch<x> and ch<x>N
simultaneously, which is beneficial for STM32 users
working in motor control area.
Signed-off-by: Savent Gate <savent_gate@outlook.com>
Driver was based on can_sam. SAMC21 has only 1 interrupt for one
can "output", so can interrupt has to executes two lines of
interrupts.
CAN is configured to use OSC48M clock via GLCK7. GLCK7 is set
by divider configured from dts.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
This driver implement basic functions of ili9342c controller
which comes mostly with IPS displays.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
The LSM6DSV16X is a system-in-package featuring a 3-axis digital
accelerometer and a 3-axis digital gyroscope for industrial and IoT
solutions. The LSM6DSV16X embeds advanced dedicated features such as
a finite state machine (FSM) for configurable motion tracking and a
machine learning core (MLC) for context awareness.
https://www.st.com/en/mems-and-sensors/lsm6dsv16x.html
This driver is based on stmemsc HAL i/f v2.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert the NPCX keyboard scan driver to the input subsystem and add the
input to kscan compatibility driver to maintain functionality with the
current API.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a USB device controller driver skeleton to use as a starting point
for implementing a specific driver.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Example configuration uses 'A' and 'X' key codes for longpress events.
Described behavior shows correct key codes (30 and 45), however comments
near those key codes were invalid for 'X' key. Fix that.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Glitches were observed if a GPIO pin was configured by
ROM to a non-default state and then Zephyr PINCTRL
reconfigured the pin. The fix involves using the correct
PINCTRL YAML output enable and state flags. Reading the
current spin state and reflecting into new pin configuration
if the pin is output and the drive low/high properties are
not present. We also take advantage of GPIO hardware reflecing
the alternate output value in the parallel output bit before
enabling parallel output mode. Interpret boolean flags with
both enable and disable as do not touch if neither flag is
present. We give precedence to enable over disable if both
flags mistakenly appear. Note, PINCTRL always clears the
GPIO control input pad disable bit.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Allows Ethernet communication between "cells"
in the Jailhouse hypervisor.
The vring queue deviates from a standard virtqueue
so is implemented separately.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
This allows finding the correct PCIe device when multiple devices
have the same vendor-id/device-id but differ in the class-rev register
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
