The litex_timer driver used hard coded tick rate (set to 100 ticks
per second). This commit replaces the fixed value with a call to
system function which takes under account system configuration.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Add support of Seeed 2.8" TFT Touch Shield v2.0 to ILI9340 driver.
This driver supports color pixel formats of RGB888 and RGB565.
Signed-off-by: Bernard Lee <bernard.lee@nordicsemi.no>
soc_register.h is available in most of stm32 series.
It is sometime empty or contains includes to flash_registers.h,
which is included directly with direct reference in flash driver.
soc_register.h is also included in stm32 clock drivers, but this
driver do not use direct reference to any register anymore.
Clean up these files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Cleanup logging and fix style. Use hex format specifier
for endpoint address. Remove periods from log messages.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
ESP32 can sport up to 4 network interfaces: two 802.11 (station and
ap), ethernet, and bluetooth. All of them derive from the same RDATA
register in efuse block 0. However, in most cases, the last (sixth)
octet will change like so:
- 802.11 station: mac[5] += 0
- 802.11 ap: mac[5] += 1
- bluetooth: mac[5] += 2
- ethernet: mac[5] += 3
Read "Number of universally admnistered MAC address" section in esp-idf
documentation[1] for more information.
[1] https://docs.espressif.com/projects/esp-idf/en/latest/
Signed-off-by: Leandro Pereira <leandro@hardinfo.org>
- Erase operations must be aligned to the erase-size.
- Don't need to perform an alignment check on a full erase. The offset
is not used in this case.
- Don't need to perform alignment check on a sector sized erase, as
this alignment is checked on entrance to the function.
- Removed some whitespace.
Signed-off-by: Ryan C Johnson <ryan.johnson@flex.com>
The values were swapped meaning the configured value for rxcnt was used
for txcnt and vice versa.
Signed-off-by: Sören Tempel <soeren+git@soeren-tempel.net>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This commit adds the default configuration to the flash_simualtor
to allow unaligned reads.
Disable this option when testing to increase test coverage.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
This driver introduces pinmux configuration capabilities
using zephyr apis for XEC SOCs.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Allow further extention of counter API by replacing count_up bool in
the structure with u8_t flags where one bit is used for count up
feature.
Change is not breaking API as count up property is read using
counter_is_counting_up() that didn't change.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Added a new runtime parameter to the Flash Simulator. It can be used to
ignore part of the data that is written to the simulated flash memory.
This parameter works together with max write calls parameter.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Added a new runtime parameter to the Flash Simulator. It can be used to
ignore erases to the simulated flash memory after a certain number
of flash erase calls has been executed.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Kconfig symbols I2C_STM32_V1 and I2C_STM32_V2 depends on SoC reference
and user should not have the possibility to choose one or the other.
Remove prompt on these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
It is recommended that multibyte (burst) transfers are used to read
acceleration and temperature data. This ensures the data is concurrent
and complete.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
There was a missing break at the end of the high speed setup case,
so it would always return -ENOTSUP even when the high speed baud
was available.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This commit consolidates the temperature conversion into a single
location and subtracts the bias from the measurement using values from
the datasheet. Also magic numbers have been replaced with more
descriptive macros.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
This driver uses magic numbers which are incorrect. A correct conversion
is done using the LSB/g scale factors given by Table 1 in the
specifications section of the ADXL362 (Rev. F) datasheet. The entire
conversion has also been consolidated into a signal function.
The sensitivity and offset of the accelerometer values actually vary
with the supply voltage and temperature. Using datasheet provided values
for 25 C and 2.0 V is the best we can do. Users will need to apply
sensitivity and offset corrections for their application.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The return code check and error return on the interrupt register
configuration function call should be included in the #if defined
region.
Fixes#16159
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
On STM32 series currently available in Zephyr,
LPUART and U(S)ART IPs are similar and share most of their
registers. As a consequence LL API defined for U(S)ART also
applies to LPUART.
This allows to remove specific LPUART code.
Restrict use of LL LPUART API when it diverges from UART one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The 50-odd lines of boilerplate per I2C port is moved into a template
which is generated by CMake as needed at build-time.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The second serial port (UART_1) can be used for connecting to
host serial port. This is used for example by PPP (Point-to-Point
Protocol) implementation in which case the pppd running in Linux host
connects to a pty that is linked to UART_1 in Zephyr.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The u-blox SARA-R4 modem modules are Ultra-compact LTE Cat
M1 / NB1 ready:
- Configurable with a single hardware version
- Flexible mode selection as LTE Cat M1, LTE Cat NB1, EGPRS -
only/preferred
- Low power consumption and longer battery life
- Extended range in buildings, basements, and with NB1,
underground
This driver introduces support for basic AT commands to
query modem information as well as socket connection
for TCP/UDP communication.
Signed-off-by: Michael Scott <mike@foundries.io>
The WNC-M14A2A shield configuration has HW specific settings in place.
We can remove those settings here.
Signed-off-by: Michael Scott <mike@foundries.io>
Assert is checking the array size of pinconfig. Not the actual
size of the structure.
Fixes issue reported by Github User @weinholtendian
Signed-off-by: Michael Scott <mike@foundries.io>
Caller will handle freeing packet if error is encountered.
Fixes issue reported by Github User @weinholtendian:
<err> net_pkt: *** ERROR *** pkt 0x20027e78 is freed already
by offload_sendto():1717 (context_sendto():1473).
Signed-off-by: Michael Scott <mike@foundries.io>
https://github.com/zephyrproject-rtos/ci-tools/pull/65 tweaks the check
for references to undefined Kconfig symbol to whitelist anything on the
form 'CONFIG_FOO_*' (or 'CONFIG_FOO_*_...'). This is meant for #endif
comments that talk about many related symbols.
Fix two existing #endif comments to use that format, so that some
entries can be removed from the whitelist in the CI check.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The value of GPIO_INT_ACTIVE_LOW is 0, so the bit checking if statement
is never executed. Use GPIO_INT_ACTIVE_HIGH when checking this bit.
Fixes#16162
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
If reception was longer than rx timeout, UART_RX_RDY event
would provide data with delay, and synchronise at buffer end.
This change makes sure that all data is given to user when timeout
occurs.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add LiteX interrupt controller driver and bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX timer driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
