Some files were using definitions from sys_clock.h, e.g. MSEC_PER_SEC
without including the header.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Change automated searching for files using "IRQ_CONNECT()" API not
including <zephyr/irq.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some headers made use of types defined in sys_clock.h (e.g. k_timeout_t)
without including it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Many device pointers are initialized at compile and never changed. This
means that the device pointer can be constified (immutable).
Automated using:
```
perl -i -pe 's/const struct device \*(?!const)(.*)= DEVICE/const struct
device *const $1= DEVICE/g' **/*.c
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Update watchdog drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
Following zephyr's style guideline, all if statements, including single
line statements shall have braces.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds basic support for the watchdog timer on the RP2040 MCU and
Raspberry Pi Pico development board
Signed-off-by: Jamie McCrae <spam@helper3000.net>
Add watchdog support to the mimxrt595 platform.
The mimxrt595 platform is excluded from the watchdog
test case because the test case uses variables in the
noinit section that need to be retained through a reset
but the rt595 does not retain this memory through a
reset.
Signed-off-by: Chay Guo <changyi.guo@nxp.com>
The Kconfig encodes a dependency on SOC_FAMILY_ARM
even though there is no actual dependency.
This is generic ARM IP and can be used in any SoC.
Signed-off-by: Moritz Fischer <moritzf@google.com>
All the watchdog drivers are based on devicetree and we dont utilize
HAS_DTS_WDT anywhere so we can remove it.
Signed-off-by: Kumar Gala <galak@kernel.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The it8xxx2 watchdog Kconfig options are always shown, for every type
of device, they should only be shown when an it8xxx2 device is being
targeted.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
In the function iwdg_stm32_install_timeout, the test on watchdog ready
was inverted. So, if 2 successive calls were made to this function, the
value of the prescaler or counter reload was not taken into account.
Signed-off-by: Julien D'Ascenzio <julien.dascenzio@paratronic.fr>
Instead of selecting appropriate HAS_HW_NRF_* options for particular
nRF SoCs (and simulated nRF52 target), set their values basing on
information from devicetree.
Correct also semantics of those options so that they are set only when
a corresponding DT node is enabled. This allows using them directly in
Kconfig dependencies of Zephyr drivers for nRF peripherals. Update
appropriately these dependencies.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Re-running the script that checks for the const qualifier missing on
struct device ISR's parameter.
The script also changes the parameter 'arg' to 'dev' when relevant.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Just use dev->name. This change follow same principles applied when
DEV_CFG and DEV_DATA macros were removed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
MCUX watchdog timer supports min window of 500ms. Increase maximum task
watchdog timeout window to 500ms by default, so that this sample can run
on iMX RT SOCs. Also update iMX RT watchdog driver to reject timeout
maximums under 500ms with a useful error message
Fixes#40153
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This corrects the following:
1. The priority of type cast is lower than member access. So don't need
the redundant parentheses.
2. The macro should be added to the parentheses.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Replace all get_dev_data()/get_dev_config() accessor utilities with
dev->data and dev->config.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add watchdog0 to support tests/drivers/watchdog/wdt_basic_api.
Solve tests code runtime error on it8xxx2_evb:
1.When run the wdt tests api, we shouldn't reduce the warning
timer time, so I add config WDT_ITE_REDUCE_WARNING_LEADING_TIME,
this config will be enabled only on platform EC.
2.Upper limit window timeouts can't be 0 when we install timeout.
3.Since we support wdt_it8xxx2_disable(), then we should support
flag WDT_OPT_PAUSE_HALTED_BY_DBG, too. Watchdog can be stopped
by IT8XXX2_WDT_EWDSCEN bit of ETWCTRL reg.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
This commit is enabling the Debug support clock
like the stm32L0 or F0, the APB peripheral clock enable register 1
has a bit to clock DBGMCU before use.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit is controlling the WWDG during the Stop mode in debug.
WWDG1 is frozen while the core is in Debug mode, setting the bit
of the DBGMCU APB1 peripheral freeze register (DBGMCU_APB1FZ2)
for the stm32MP1 soc devices.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit is controlling the WWDG during the Stop mode in debug.
WWDG1 is frozen while the core is in Debug mode, setting the bit
of the DBGMCU APB3 peripheral freeze register (DBGMCU_APB3FZ1)
for the stm32H7 soc devices.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Added watchdog implementation which is using counter device
to implement watchdog driver API. Watchdog timeout is called from
counter interrupt context. Some counter implementations support
using ZLI interrupt level which can be use here as well. Watchdog
like this can be used along hardware watchdog to cover for its
limitations, i.e. Nordic watchdog resets unconditionally after
62uS after triggering watchdog interrupt. It is not enough time
to dump logging data.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
