GPR17 calculation for configuration of RAM banks is incorrect,
bit shift should be 2 per idx, not 1, this is major bug that needs
correcting, currently all RT boards are affected with wrong
configuration.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
One of the ARM architure files, defined since long ago
CONCAT having the exact same purpose as Zephyr's _CONCAT.
Unfortunately this header is included almost always
and the macro defined in all ARM based platforms,
which seems to have lead to many uses of this macro
instead of _CONCAT.
Fix it by using _CONCAT instead.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Update interface of memc flexspi driver to better handle multiple
devices. Previously, using multiple devices on one FlexSPI bus would
require the user to configure each device to install its command table
(referred to as a LUT table by the driver) at an offset, so that it did
not overlap with other devices on the bus.
This commit changes the interface of the memc flexspi driver to instead
configure the LUT and flash device in one call. This allows the memc
driver to record the port each LUT sequence is used with, so that
future FlexSPI transfer requests can have their LUT offsets adjusted
based on the target port (which will correspond to a target device)
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Check XIP state based on the value of CONFIG_FLASH_BASE_ADDRESS. This
check should be more reliable than the SOC based method currently
used.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The NXP S32 QSPI controller acts as an interface to up to two serial
flash memory devices, each with up to eight bidirectional data lines,
depending on the platform. It is based on a LUT enginee to interface
through commands with different memory types including flash NOR and
Hyperram.
This patch adds support for the QSPI in S32K344 which supports a single
memory device (side A) with up to four bidirectional data lines and SDR
only. Nevertheless, the memory controller is implemented flexible enough
to be extended to support more feature-rich QSPI blocks.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add a function to update the flexspi bus clock. This is
needed when write operations are done to the hyperflash.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The MCUX platform always uses pinctrl, there's no need to keep extra
macrology around pinctrl. Also updated driver's Kconfig options to
`select PINCTRL` (note that some already did).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
HAL API changes in ethernet and pwm
SoC RT595 power management code change
west.yml update
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update flexspi driver init priority to be the
memc driver init priority. This fixes a bug where
the flexspi flash drivers on i.MX RT platforms were
being initialized before the flexspi memc driver.
Since those flash drivers depend on the flexspi
spi bus controller being initialized, the flash drivers
would fail to initialize and cause runtime failures.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Allow configuration of AHB RX buffer allocation. This allows sections
of the AHB RX buffer to be reserved for specific masters, which can
enhance performance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update usage of zephyr_code_relocate to follow new API. The old method
of relocating a file was the following directive:
zephyr_code_relocate(file location)
The new API for zephyr_code_relocate uses the following directive:
zephyr_code_relocate(FILES file LOCATION location)
update in tree usage to follow this model. Also, update the NXP HAL SHA,
as NXP's HAL uses this macro as well.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce driver for APS6408L PSRAM, built on top of the MCUX memc
driver for flexSPI. This driver supports operating the PSRAM in high
speed mode (200MHz or more). Note that in order to support this
PSRAM's alignment requirements, either ahb-read-addr-opt or
ahb-prefetch must be set for the FlexSPI instance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
memc driver was setup to always assume the flexSPI would be in XIP mode,
and skip init. This is only true for the active flexSPI, which is
typically FlexSPI1. Fix this check to only skip init for FlexSPI1
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rename flexspi-hyperram driver to flexspi-s27ks0641, and update
function names. This driver is only capable of supporting the
s27ks0641 HyperRAM chip, as the lookup table given in this driver
is specific to the s27ks0641.
Rename the flexspi-hyperram binding to reflect this, to
prevent confusion from users.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Only relocate memc driver when CONFIG_FLASH=y.
CONFIG_FLASH_MCUX_FLEXSPI_XIP previously was dependent on
CONFIG_FLASH, but the scope of this Kconfig has changed.
Due to this, the memc driver now must have two checks, as it should not
relocated when the driver is being used for a memory controller that does
not expose the flash driver interface.
Since the NXP HAL also relocates the underlying FlexSPI driver
using a similar check, it is updated in this commit as well.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit fixes an issue introduced in 5ee9392 where FlexSPI
pinctrl states where applied based on the SoC type.
However multiple FlexSPI instances can be active, some of which
are not pre-configured from ROM.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Update memc drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
Enabling the FlexSPI HyperRAM results in a build error, due to a logging
module re-definition. Fixed by changing the log module name.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
- The MX25UM51345G flash is connected to FLEXSPI PortA for
mimxrt595_evk.
- Updated flexspi_mx25um51345g driver to support DTR OPI mode.
- Tested with tests/drivers/flash.
Signed-off-by: Chay Guo <changyi.guo@nxp.com>
Some SOCs, such as the RT1064 and RT1024, use internal flash and don't
define pinmux settings for the flexspi. Don't check the return code of
pinctrl_apply_state, because the flexspi driver will fail to initialize
when the pin mux settings are simply not required.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Enable pinctrl for flexspi driver. Note that when flexspi is being using
in XIP mode, pinctrl settings are not required and will not be applied.
Pinctrl settings are only required when the flexspi device being used is
not the one used for XIP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
flexspi driver should not interact with flash whenever possible, and
should never use flash while in a critical write or erase section.
Move device data to RAM to prevent this read-while-write hazard.
Fixes#44043
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
flexspi driver should not interact with flash whenever possible, and
should never use flash while in a critical write or erase section.
Move device data to RAM to prevent this read-while-write hazard.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PINCTRL_DT_(INST_)DEFINE macros already defined the trailing ;,
making its usage inconsistent with other macros such as
DEVICE_DT_DEFINE.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Replace usages of DT_PARENT(DT_DRV_INST(idx)) with more idiomatic
DT_INST_PARENT(idx).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Program flow will behave incorrectly (memory and instruction fetches
return invalid data) if Flexspi is accessed by the Flexspi driver while
being used as XIP memory by the Cortex M7.
Set logging to disabled by when XIP mode is used in the memc and
flexspi drivers, and warn the user if they attempt to enable it.
Fixes#40133
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
With the introduction of `EXPERIMENTAL` and `WARN_EXPERIMENTAL` in
Zephyr all drivers settings having `[EXPERIMENTAL]` in their
prompt has has been updated to include `select EXPERIMENTAL` so that
developers can enable warnings when experimental features are enabled.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This enables accessing the hyperflash through the flash api.
Added a feature to memc_mcux_flexspi that waits for flexspi bus to be
quiet.
Signed-off-by: Nicolai Glud <nicolai.glud@prevas.dk>
Instead of putting object files inside libzephyr.a,
simply build a separate static library as most other
driver types are doing this already.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Updating to the SDK 2.10.0 for select platforms.
west.yml:
- Update to point to the NXP HAL update with SDK 2.10.0 files
- modules/tee/tfm needed to be updated to synchronize the
LPCXPRESSO55S69 platform SDK to version 2.10.0 to be in sync
with Zephyr usage of SDK 2.10.0
drivers/counter/counter_mcux_pit.c:
- underlying SDK 2.10.0 adjusted the setting by -1 so need
to adjust the reported value set by +1
drivers/ethernet/eth_mcux.c:
- SDK2.10 ethernet driver provided an assert test that highlighted
we were using the wrong clock source on various platforms.
drivers/memc/memc_mcux_flexspi.c:
- SDK2.10 added compile time conditional on whether a field was
defined for the flexspi configuration structure.
Signed-off-by: David Leach <david.leach@nxp.com>
Default the option MEMC_STM32 to "y" when the device node is defined and
enabled, so that the driver is selected automatically when the board
supports it and MEMC is enabled.
Remove the default conditional on serise as it's redundant with the one
in soc/arm/st_stm32/common/Kconfig.defconfig.series.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Since we removed various series headers, move stm32 driver
under main driver/pinmux folder.
Take this change into account into various drivers.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
