The LPS22DF is an ultracompact, piezoresistive, absolute pressure sensor
that functions as a digital output barometer. The LPS22DF provides lower
power consumption, achieving lower pressure noise than its predecessor.
This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/en/datasheet/lps22df.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
NXP USB bindings were combined into one binding and using
a property corresponding to HAL enums which is improper use
of devicetree.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Fix indentation to use spaces (instead of tabs) and remove the
unnecessary repetition of the condition inside endif().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Added initial version of Infineon AIROC WIFI driver
Added initial version of binding file for Infineon AIROC WIFI
driver
Rename CONFIG_ABSTRACTION_RTOS_COMPONENT_ZEPHYR to
CONFIG_USE_INFINEON_ABSTRACTION_RTOS
Exclude cy8cproto_062_4343w platform from
drivers.modem.esp_at.build test
Change revision hal_infineon to
69c883d3bd9fac8a18dd8384624b8c472a68d06f
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 SDHC/SDIO driver
Added initial version of binding file for Infineon CAT1 SDHC/SDIO
driver
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Rename local usbd copy from nrfx_usbd to nrf_usbd_common and use it in
both USB stacks. Renaming header to nrf_usbd_common.h allows breaking
changes in exposed interface. Mark all doxygen comments as internal
because local usbd copy should not be treated as public interface
because we are under refactoring process that aims to arrive at native
driver and therefore drop nrf_usbd_common in the future.
Use Zephyr constructs directly instead of nrfx glue macros.
No functional changes.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Copy nrfx_usbd code from zephyrproject-rtos/hal_nordic git revision
d054a315eb888ba70e09e5f6decd4097b0276d1f. This enables us to refactor
the code towards a native driver in a step by step manner where the
smallest changes that bring biggest performance improvements are done
early on.
The code is not a vanilla copy from zephyrproject-rtos/hal_nordic.
The code was reformated with clang-format to match project style.
Manual modifications were done to change comments formatting, place
constant comparisons on the right and add blank lines to pass Zephyr
compliance check.
Relicense to Apache 2.0.
No functional changes.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
The LC3 coded requires floating point support in
the C library, so let's select REQUIRES_FULL_LIBC
in the module kconfig, instead of having samples
adding it to their prj.conf
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add choice for BL2 log level configuration.
Silence TF-M BL2 logging when TF-M is configured to be silent.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Moving the Zephyr specific config options from
modules/hostap/Kconfig to corresponding Kconfig where the
option is specified.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Only adds basic build support using Zephyr. Crypto support is disabled
till the MbedTLS integration is complete.
Signed-off-by: Sridhar Nuvusetty <sridhar.nuvusetty@nordicsemi.no>
Signed-off-by: Sachin Kulkarni <sachin.kulkarni@nordicsemi.no>
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Now it is needed to explicitly use NRF_GPIOTE1 instance
in nrfx_gpiote driver for non-secure builds.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add generic SoC support for the supported nordic SoCs:
- nrf5340
- nrf9160
- nrf9120
Add generic SoC support by taking board specific configurations from
zephyr devicetree and kconfig.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Exception info dump is a very basic feature so it should IMHO be
enabled by default.
For instance, a simple null-pointer exception in the non-secure app
will not be logged unless this option is enabled.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Uart driver for openthread have been waiting for host to start
communicating with coprocessor, during booting of the Zephyr and
by that blocking start os OS. There is no longer a need for
that since the stack will be soft rebooted after host connects
to coprocessor, removing the need to wait on host communication.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
This change slightly simplifies the configuration of a CSL receiver and
generalized CSL_RX_TIME to EXPECTED_RX_TIME as a re-usable primitive
across several timing-sensitive IEEE 802.15.4 standard sub-protocols
(namely BE-PANs/DSME/CSL/RIT/TSCH).
This API change is based on the rules outlined in RFC #61227.
Fixes: #62918
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Improves standard conformance of the IEEE802154_CONFIG_ENH_ACK_HEADER_IE
option and introduces certain "soft MAC" capabilities around header IEs:
* Introduces types and helpers that allow driver maintainers to
represent, parse, write and validate header IEs.
* Introduces helper functions to access non-aligned fields in header
IEs, namely element IDs.
Updates the only existing L2 and driver pair that uses
IEEE802154_CONFIG_ENH_ACK_HEADER_IE: OpenThread platform radio and nRF5
and improves header IE validation in the nRF5 driver.
This change should help further driver maintainers to support
OpenThread's CSL and vendor IE extensions. It is based on the rules
specified in RFC #61227.
It is also a precondition to generically support both, "soft MAC" and
"hard MAC", approaches to header IEs in the TSCH protocol, namely the
time synchronization IE.
Fixes: #62940
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
"Sleeping" has a well defined meaning in Zephyr related to threading and
power management. This differs from OpenThread's definition:
- Deprecates the "SLEEP_TO_TX" capability as it is redundant and
conflicts with all of Zephyr's nomenclature, #61227, RFC 2863, Thread
standard and IEEE 802.15.4. This binds the API to an implementation
detail of OpenThread, instead. See #63670 for the agreed migration path.
- Renames the "SLEEP" event to "RX_OFF" which conforms to the
nomenclature in Zephyr, this API and IEEE 802.15.4.
Fixes: #62995
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
According to cmake documentation, in the `if(<string>)` expression
the string evaluates to false unless its value is one of the true
constants. Thus, the commands under `if(${uicr_path})` are never
executed. Use `if(DEFINED uicr_path)` instead, since `uicr_path`
is returned by `dt_nodelabel()` and it will be undefined if such
node does not exist.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add option for overriding the maximum number of wait loop iterations for
entering/leaving freeze mode. Set the default to 10000 (as opposed to a
default of 1000 used in the HAL).
Fixes: #56171
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
rand32.h does not make much sense, since the random subsystem
provides more APIs than just getting a random 32 bits value.
Rename it to random.h and get consistently with other
subsystems.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
CONFIG_HAS_MCUX is also selected by ARM64 and XTENSA-based cores
which don't have any CMSIS files. As such, it's wrong to implicitly
select CONFIG_HAS_CMSIS_CORE when CONFIG_HAS_MCUX is selected. Since
the ARM32-based cores implicitly select CONFIG_HAS_CMSIS_CORE there's
no point in CONFIG_HAS_MCUX also selecting it too.
The old approach caused config-related warnings
in external projects such as SOF after the introduction of
Commit '8d5ed53' ("modules: remove uncessary source for
external cmsis kconfig"). The warnings were in the form of:
"HAS_CMSIS_CORE (defined at modules/cmsis/Kconfig:7) has
direct dependencies 0 with value n ..."
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
ethosu_log.h uses the stdout as it's stream for printf. This could
cause an issue where if CONFIG_LOG=n and CONFIG_CONSOLE=y then there
would be no way to control the log level and it would default to debug
level. There is no NONE option as with the way the ethos-u hal is set
up with no way to go below the err level.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
A little refactoring that simplifies dealing with nanosecond timestamp
values in packets and further decouples calling code from PTP:
Benefits:
- simplifies calling code by removing redundant conversions.
- prepares for removing PTP dependencies from net_pkt.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Do not select HAS_CMSIS_CORE for SOC_FAMILY_NXP_ADSP.
This soc family refers to the Audio DSP from i.MX MPU,
which is a HiFi4 core, Xtensa arch.
HAS_CMSIS_CORE is for ARM cores (A, M, R cores) -
see modules/cmsis/Kconfig.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
CMSIS uses an external KConfig so sourcing the KConfig is uncessary. This
also adds a comment if it is not available.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The names have underscores within them. Somehow it was still being found
within the build but not with building documents. This renames them to
the correct name.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Code using sys_csrand_get should depend on CONFIG_CSPRNG_ENABLED symbol
and not in ENTROPY_HAS_DRIVER since they are not using the entropy
device directly.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The CONFIG_MCUBOOT_BOOTLOADER_MODE_DIRECT_XIP has been missing
select of CONFIG_MCUBOOT_BOOTLOADER_MODE_HAS_NO_DOWNGRADE.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Changes the Kconfig symbols for the sys_heap based memory management option
and removes the notion of `BLOCKS` with a more concise single
`LV_Z_MEM_POOL_SIZE` option. Also adds `LV_MEM_CUSTOM` to the lv_conf.h,
since in any option the memory management is considered to be custom.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Add the MCUBOOT_BOOTLOADER_NO_DOWNGRADE Kconfig option that allows,
when paired with MCUboot mode Kconfig, to indicate that the MCUboot
has been configured with downgrade prevention, which means that only
application with version higher than running can be swapped on next boot.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit adds support for uploading image to board with MCUboot
configured with DirectXIP with revert.
It allows to set uploaded image either for test or as permanent
boot application, until newer image gets confirmed.
Note that in DirectXIP with revert MCUboot will remove image
that has not been set for test nor confirmed and MCUmgr does not
set either mode unless image has the mode set within uploaded
binary.
The commit adds Kconfig option
CONFIG_MCUBOOT_BOOTLOADER_MODE_DIRECT_XIP_WITH_REVERT
that enabled the new mode of operation within MCUmgr.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This adds the cmsis-nn module since it moved to its own realm.
This also adds a kconfig for the long short-term memory.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Use CMSIS-DSP from its new realm. This also changes change how you
initialize FFT tables as well to use arm_cfft_init_64_f32 if you
know the FFT size in advance rather than the generic initialization
arm_cfft_init_f32.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Adds CONFIG_STM32_ENABLE_DEBUG_SLEEP_STOP to allow debugger attaching in
sleep/stop mode of STM32 parts. Mainly useful for debugging. Move DBGMCU
from part-sepcific power.c to common soc_config.c. CONFIG_USE_SEGGER_RTT
depends on this as well.
Signed-off-by: Roland Lezuo <roland.lezuo@embedded-solutions.at>
Also set the HAL variant appropriately when building for
the new nrf53_bsim boards.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Adds saving of the last lv_indev_data_t for button and pointer type
devices. This is needed because there is currently no way to tell LVGL in
the read callback that no event is pending. Preservation of the last state
is expected to happen in the port layer for the input devices.
This resolves issue #62512.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
If asserts are disabled, there is a warning in 'otPlatCryptoInit'
regarding unused variable `err`. This commit fixes that.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
Synchronizes with the new upstream RX/TX timestamp definition in
OpenThread based on the standard's SFD.
This change is synchronized with the upstream OpenThread implementation
via west.yml.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Removes the pseudo device prerequisite that the LVGL setup routine has been
executed before initialization. The pseudo devices are now registered at
the end of the LVGL setup routine, the driver is not concerned with
configuring the devices anymore. This also removes the need for enforcing
certain priorities within the same init level.
This resolves issue #62753.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
So that the HAL's system init function configures the reset GPIO as
nRESET if requested by the user.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
If the users configures this option in devicetree, ie,
```
&uicr {
nfct-pins-as-gpios;
};
```
CMake will inject the HAL-specific CONFIG_NFCT_PINS_AS_GPIOS definition,
so that the necessary operations are performed during system init.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Instead of detecting that we are in a native/POSIX arch based
board by checking for each board specifically,
let checks for the architecture.
In that way other boards (like the upcoming nrf53_bsim ones)
will also work.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Introduce a helper function zephyr_nanopb_sources to generate
source files and add these to a target.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Move the conditional compile of CONFIG_ACPI to the beginning of the file
as we currently add compiler include paths to all projects even if
CONFIG_ACPI is not set.
Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>
Adds a missing include to avoid these warnings :
- zephyr/modules/fatfs/zfs_ffsystem.c:19:16: warning: implicit declaration
of function 'k_malloc'; did you mean 'ff_memalloc'?
[-Wimplicit-function-declaration]
- zephyr/modules/fatfs/zfs_ffsystem.c:19:16: warning: returning 'int' from
a function with return type 'void *' makes pointer from integer without a
cast [-Wint-conversion]
- zephyr/modules/fatfs/zfs_ffsystem.c:25:9: warning: implicit declaration
of function 'k_free' [-Wimplicit-function-declaration]
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
This commit instructs mbedtls to use 64-bit alignment in its internal
memory allocation routines when targeting 64-bit platforms. By default
mbedtls uses 32-bit alignment regardless the platform, what may result
in misaligned memory accesses, possibly inducing access time overhead or
exceptions
Signed-off-by: Vladimir Graudt <vladimir.graudt@syntacore.com>
Add a pseudo device which can be used to hook into qdec events and
optionally a button and relay the input_event to lvgl.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
This commit follows the parent commit work.
This commit introduces the following major changes.
1. Move all directories and files in 'include/zephyr/arch/arm/aarch32'
to the 'include/zephyr/arch/arm' directory.
2. Change the path string which is influenced by the changement 1.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
This commit adds the DFM (DevAlert target side code) module and
moves the TraceRecorder module into the percepio module, which
results in the TraceRecorder module definition being removed
from the west manufest and module definition within zephyr.
Signed-off-by: Aron Lander <aron.lander@percepio.com>
Call lvgl_heap_init from lvgl_init rather than using two separate
SYS_INIT, this sensures that the heap is initialized correctly
regardless of the relation between CONFIG_KERNEL_INIT_PRIORITY_DEFAULT
and CONFIG_APPLICATION_INIT_PRIORITY.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
add support for retrieve MAD and DMAR table information. Provided
two new interface namely acpi_dmar_entry_get() and acpi_drhd_get()
for retrieve DMA Remapping Reporting and DMA-remapping hardware
unit definition (DRDH).
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
Includes the application VERSION-file designated tweak version
for the build number field when signing MCUboot images.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add a pseudo device which can be used to hook into gpio-keys input_events
and relay the events to a lv_indev.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Moves lvgl pointer driver handling based on kscan to its own file, to ease
deletion when the usage of kscan for display touch input has been
deprecated.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Add the scaffolding to create input lvgl pseudo devices which route zephyr
input_event to their lvgl `indev` equivalent. As a first cut also add a
`zephyr,lvgl-pointer-input compatible which can be a drop-in replacement
for the existing kscan solution.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
In OpenThread, Settings are initialized after KeyManager by default.
If device uses PSA with emulated TFM, Settings have to be initialized
at the end of otPlatCryptoInit(), to be available before storing
Network Key.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
The CMSIS module glue code was part of arch/ directory. Move it to
modules/cmsis, and provide a single entry point for it: cmsis_core.h.
This entry header will include the right CMSIS header (M or A/R).
To make this change possible, CMSIS module Kconfig/CMake are declared as
external, allowing us to add a new Zephyr include directory.
All files including CMSIS have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move CMSIS module Kconfig options to a folder, in preparation for CMSIS
core header creation.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Enable offloading of display_write call to background thread for color
displays. This feature is opt-in, as it may offer significant
performance gains for every display pipeline.
When enabled display_write and lv_disp_flush_ready will be called from a
background thread. This means that while the display driver waits on the
hardware to render the framebuffer, the LVGL rendering thread will not
be blocked.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Changes the lvgl filesystem `tell()` wrapper to check for errors returned
by zephyr filesystem subsystem.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Changes the memory management for the lvgl filesystem wrapper to use the
memory management strategy selected by kconfig. Additionally fixes memory
leaks if fs_{file,dir}_t initialization failed.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
The prototype of `nrf_802154_energy_detected` callout has changed.
This commit adjusts to this change.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Commit adds configuration for mesh with mbedtls PSA
to CI BabbleSim tests as well as emulation of
the Internal Trustable Storage(ITS) based on Zephyr's
settings to run in parallel environment.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Based on the standard based definitions given in previous commits, the
TX timestamp used for timed TX now refers to the start of PHR. As OT
continues to calculate timestamps based on a "start of SHR" definition,
the duration of the PHY specific SHR is added in the OT adaptation layer
to make up for this OT quirk.
Fixes: #59245
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
