PHY TX power configuration must be added into soc level.
It was previously hardcoded in hal_espressif, which was removed.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Some sockets (UDP sockets at least) do not generate "<N>,CLOSED"
messages when the WiFi network drops. As a result the networking stack
thinks these sockets are still open after the network has dropped, and
after any subsequent reconnections.
This affects the DNS resolver library in particular, which leaves UDP
sockets open permanently by default.
Manually close these sockets when the network drops to ensure a clean
state the next time the network connects.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
`esp_close_work` can be queued from the `on_cmd_closed`, which clears
`ESP_SOCK_CONNECTED` and sets `ESP_SOCK_CLOSE_PENDING`, but does no
further work. The receive callback should still be run with no data when
the socket is closed through this mechanism.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Log a message when the modem asynchronously closes a link. This is
useful information to the user as it can explain the root cause of later
failures.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Use the proper `%p` printf specifier when printing memory addresses,
instead of casting to an integer, which may not be the same size as a
pointer.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a separate macro for registering offloaded sockets implementation,
along with information in the structure whether the implementation is
offloaded or not. This allows to differentiate between native and
offloaded socket implementations, which is critical for binding socket
API with an interface.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Instead of keeping a boolean informing whether a network interface is
offloaded at socket layer or not, keep a pointer to a function which
allows to create an offloaded socket. Native interfaces keep this as
NULL, while for offloaded interfaces it allows to connect an offloaded
socket implementation with an interface.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Check if requested socket family, type and protocol are all supported by
the driver, instead of blindly acknowledging every possible variant.
Reuse switch statements checking valid parameter values that were
already part of simplelink_socket() function, by creating 3 helper
functions for conversion of each parameter (family, type and protocol)
from Zephyr to Simplelink values.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Check if requested socket family, type and protocol are all supported by
the driver, instead of blindly acknowledging every possible variant.
There is explicit support for UDP, TCP and TLS on top of IPv4.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Use NET_SOCKETS_OFFLOAD_PRIORITY instead of
NET_SOCKETS_OFFLOAD_PRIORITY, so that by default offloaded sockets will
be used instead of native sockets.
Addiitonally this allows to select relative priority of offloaded TLS
versus native TLS when used together with NET_SOCKETS_TLS_PRIORITY.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Use NET_SOCKETS_OFFLOAD_PRIORITY instead of
NET_SOCKETS_OFFLOAD_PRIORITY, so that by default offloaded sockets will
be used instead of native sockets.
Addiitonally this allows to select relative priority of offloaded TLS
versus native TLS when used together with NET_SOCKETS_TLS_PRIORITY.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Reset the ESP modem inside the device initialisation function so that
errors can be detected through the use of `device_is_ready`.
Fixes#43891 for this driver.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Move the network device instantiation macro to above the esp_init
function so that static variables declared by the macro are visible to
the init function.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
In the newer ESP32 AT command versions, the CWMODE command takes an
optional parameter (<auto_connect>) which controls whether the module
will automatically attempt to connect to an AP when switching modes.
This parameter defaults to enabling auto-connect if not specified.
Without this change, modules can successfully connect to an AP before
the `CWAUTOCONN=0` command is processed, resulting in a
`NET_EVENT_WIFI_CONNECT_RESULT` before `NET_EVENT_IF_UP`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Claim the net_context mutext associated with a socket before claiming
the socket mutex. The receive callback claims the net_context mutex
internally, which will now always succeed immediately.
The TX path claims the net_context mutex before the socket mutex, and if
we don't use the same order, we can end up in a deadlock.
Fixes#43470.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Previous commit 579ca90e25 to
build wifi drivers as a library changed the include path for
the WINC1500 driver, which results in the include path being
local to the library. However, the Atmel HAL requires
wifi_winc1500_nm_bsp_internal.h to in the search path. So
change the include path to be global.
Fixes#43456
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
spi_dt_spec structure initialization should not be done
in the runtime during spi bus initialization because it
caues kernel panic.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/43046
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
A common pattern here was to take the work item as the subfield of a
containing object. But the contained field is not a k_work, it's a
k_work_delayable.
Things were working only because the work field was first, so the
pointers had the same value. Do things right and fix things to
produce correct code if/when that field ever moves within delayable.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data
and dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Adding these definitions help ease of porting POSIX applications.
They currently do nothing in the core network stack and will
return an error if used. However, they help port some POSIX
without changing these. In particular, this enables using the
Nim programming language's standard library with Zephyr.
- The values copy Linux amd64, similar to the other SO_OPTIONS
- Add SO_SNDBUF to fix simplelink wifi
- Use compat options in simplelink wifi
Signed-off-by: Jaremy J. Creechley <jaremy.creechley@panthalassa.com>
Fix a problem introduced in 6ea54db334 that caused the poll operation to
take 10x more time than intended.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Sending AT+CWLAP was introduced with commit f2859f9501 ("drivers:
wifi: esp_at: changes to scanning") as a way to easily test introduced
changes, rather than on purpose. Remove that now, as there is no
particular reason to send it and additionally it breaks setup phase:
<err> modem_cmd_handler: command AT+CWLAP ret:-5
<err> wifi_esp_at: Init failed -5
with ESP-AT firmware v2.1.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Size of data pointer for event revival must be at least sizeof
event queue item.
Update to send whole event (id + event)
Signed-off-by: Pavlo Hamov <p.hamov@venstar.com>
If CONFIG_WIFI_ESP_AT_SCAN_MAC_ADDRESS: mac addr included in
scanning results.
if CONFIG_WIFI_ESP_AT_SCAN_PASSIVE: passive scanning is used instead of
default active scanning.
If CONFIG_WIFI_ESP_AT_SCAN_RESULT_RSSI_ORDERED: scanning response
ordered by RSSI.
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
When creating a socket, all of the registered socket implementation are
processed in a sequence, allowing to find appropriate socket
implementation for specified family/type/protocol. So far however,
the order of processing was not clearly defined, leaving ambiguity if
multiple implmentations supported the same set of parameters.
Fix this, by registering socket priority along with implementation. This
makes the processing order of particular socket implementations
explicit, giving more flexibility to the user, for example when it's
neeed to prioritze one implementation over another if they support the
same set of parameters.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Instead of putting object files inside libzephyr.a,
simply build a separate static library as most other
driver types are doing this already.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is more or less the flow of AT+CIPSEND:
RX TX
-- --
AT+CIPSEND=<...>
OK
>
<data to be sent>
SEND OK / SEND FAIL
'sem_response' semaphore is released by receiving 'OK'. Then after
receiving '>' (which releases 'sem_tx_ready' semaphore) actual data is
sent. Waiting for 'SEND OK' or 'SEND FAIL' is implemented by waiting on
'sem_response' (the same as for 'OK'), which mean that resetting this
semaphore just after sending all data is racy.
Fix that race condition by resetting 'sem_response' just after receiving
'OK', so that neither 'SEND OK' nor 'SEND FAIL' will appear yet (they
will not be sent as long as we won't send whole payload).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Sending AT+CIPSEND=<...> command results in following reply:
OK
>
modem_cmd_send_nolock() invocation was setting command handlers for '>',
but as 'OK' was received first, it was handled as a generic reply. After
receiving 'OK' this function was unsetting command handlers. Then
modem_cmd_handler_update_cmds() was called once again in order to
register '>' handler once again. There was a small period of time where
'>' was not being handled at all.
Fix that race condition by using just introduced modem_cmd_send_ext(),
which allows to leave commands handlers in place and get rid of race
condition where expected command could be missed.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far modem API used UART device names / labels. Change API to operate
on device pointers instead, so that we stop using device_get_binding()
in modem core and in some DT compatible modem drivers.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
hal_espressif repository was updated from esp-idf v4.2
to esp-idf v4.3 to allow latest Espressif chips integration.
As a consequence, it added a few changes in drivers
and peripherals. To maintain bisectability, changes in this
PR cannot be split. Here are some details:
wifi: update linker script by adding libphy and new attributes.
spi: update some APIs and fixed missing wait_idle check
west.yml: esp32: update hal to new version
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
If stream socket is marked as pending close, make sure that send()
caller gets notified about it, so that application layer can decide to
stop trying to send anything more.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far send errors were silently ignored. This is okay for
UDP (datagram) sockets, as there is no guarantee that packets will
actually be sent successfully. In case of TCP (stream) stream sockets
however, application layer expects network stack to send requested data
as stream, without losing any part of it.
In case of send errors on stream sockets mark that socket to be closed
and stop sending any subsequent network packets, so that data stream
won't have any holes.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Change Highlights:
- Fix error check after `k_work_reschedule_for_queue`. A value of 1
means job was scheduled which was resulting in a ton of "<err>
wifi_eswifi: Rescheduling socket read error" logs getting printed
due to the erroneous check
- When using the B-L475E-IOT01A, attempts to use a TLS socket result
in a hang when socket offload is enabled so I'd like to have a way
to disable the option. To accomplish this, I I switched the
`CONFIG_NET_SOCKETS_OFFLOAD=n` Kconfig option from `select` to
`imply`.
- There was a missing `net_context_set_state()` call when
`CONFIG_NET_SOCKETS_OFFLOAD=n`. I applied the same fix from #30664
for this case to fix the issue.
Signed-off-by: Chris Coleman <chris@memfault.com>
Commit 95b916d104 ("drivers: wifi: esp32: fix reconnect issue")
switched from thread created at runtime to statically defined thread.
The difference is mainly visible for simple applications that use
CONFIG_NET_CONFIG_AUTO_INIT=y, where networking setup code is executed
before main() and any statically defined threads. All ESP32 events are
just queued and never handled, so conditions enforced by
CONFIG_NET_CONFIG_NEED_IPV4=y are never met (e.g. Zephyr networking
layer is never informed about being connected).
Switch back to thread created at runtime, which starts at the moment
when k_thread_create() is invoked. This allows ESP32 event processing to
happen just after ESP32 WiFi driver gets initialized and before Zephyr
network auto initialization code (CONFIG_NET_CONFIG_AUTO_INIT=y).
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Device won't reconnect automatically even if
AP station is available. This fix adds the carrier event, indicating
that network is present again enabling DHCP bound event.
Also, internal wifi event callback was added into wifi
driver to enable proper event handling.
Update west.yml to bring exposed wifi event callback.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Fixes#33843
Usage of k_work object from within net_pkt results in undefined behavior
in case when net_pkt is deallocated (by net_pkt_unref()) before work has
been finished.
Use per socket k_work object (sock->send_work) to submit send work and
put net_pkt objects onto k_fifo (sock->tx_fifo). Add a helper function
esp_socket_queue_tx() for that, which will make sure that packets are
enqueued only when send work handler will be successfully submitted (so
that all packets are consumed/dereferenced).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Recently WiFi ESP32 driver (utilizing WiFi radio in ESP32 SoC) was
introduced into drivers/wifi/esp32/ and it already caused confusion as
there was existing drivers/wifi/esp/ directory for ESP-AT
driver (utilizing external WiFi chip, by communicating using AT commands
from any serial capable platform). So question has arisen whether it is
good to merge both, while they are totally different drivers.
Rename ESP-AT driver to be placed in drivers/wifi/esp_at/, so that it is
easier to figure out difference between "esp32" and "esp_at" just by
looking at driver name. Rename also DT compatible and all Kconfig
options for the same reason.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
esp_reset() is called from net_if init function, which holds net_if lock
after commit 24b49f4399 ("net: if: Add locking"). At the end of
esp_reset() there is a blocking wait on `sem_if_up` semaphore. This
semaphore can be release only by esp_init_work(). esp_init_work()
however blocks on net_if operations, because net_if init function (which
invokes esp_reset() underneath) is still holding net_if lock. As a
result there is a deadlock, because esp_reset() and esp_init_work() are
both waiting on each other.
Remove waiting for `sem_if_up`, so that net_if init can exit and release
net_if lock.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Use recently introduced API, which takes care of gracefully closing any
pending DNS requests and replacing existing DNS server list with new
one.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
When BT and WiFi coexists, IRAM usage increases a lot.
Add configuration that allow wifi symbols
to be placed in flash, freeing space in IRAM.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Replace all existing deprecated API with the recommended alternative.
Be aware that this does not address architectural errors in the use
of the work API.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Several wifi drivers add some form of zephyr_include_directories(.)
which isn't needed since the headers in the specific driver dir get
included via #include "foo.h". So we can remove any uses of
zephyr_include_directories(.)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There is a hardcoded macro in Winc1500 HAL SPI driver
that would prevent the driver from working.
This macro is now defined only based on KConfig entry.
This KConfig entry is by default not set.
To enable, set "CONFIG_WINC1500_DRV_USE_OLD_SW=y"
in proj.conf or board.conf
Signed-off-by: Raja D. Singh <rdsingh@iotwizards.com>
Convert esp driver:
NET_DEVICE_OFFLOAD_INIT -> NET_DEVICE_DT_INST_OFFLOAD_DEFINE
DT label is already required, so use it and drop CONFIG_WIFI_ESP_NAME
option.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
By the time hostname configuration was implemented, driver was switching
only between STA and STA+AP modes. After dynamic selection between NONE,
STA, AP and STA+AP was implemented (commit referenced below), hostname
configuration no longer takes effect when ESP chip obtains address over
DHCP (and sends hostname in the DHCP request).
Set hostname each time after enabling STA mode, so that it takes effect
in DHCP requests.
Fixes: 03ce61004b ("drivers: wifi: esp: control CWMODE depending on
current needs")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far received packets were parsed (at AT command level) and allocated
in [esp_rx] thread. Then they were submitted to [esp_workq] thread for
processing (calling application callback).
This flow results in following deadlock when esp_workq thread waits on
response to some AT command:
- [esp_rx] waits on allocation of new RX packet
- [esp_workq] waits for [esp_rx] to process response to AT command
that was just sent
- blocked [esp_workq] prevents processing and deallocating RX packets
- [esp_rx] times out on allocation and closes socket
Process RX packets directly from [esp_rx] thread to prevent above
deadlock.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
ESP fetches DNS servers from local network by using DHCP. There is an AT
command to get those DNS addresses. Use that to provide DNS addresses
for Zephyr's DNS resolver.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Socket can be closed either by Zephyr or by peer. In the former case ESP
WiFi chip still notfies about closed socket, which currently results in
printing warning log:
<wrn> wifi_esp: Link X already closed
Change level of this log from warning to debug, so that driver users are
not concerned about situation that is a normal behaviour.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There was a regression when implementing automatic AT+CWMODE{,_CUR}
handling based on driver needs. ESP AT 1.7 firmware does not support
AT+CWMODE_CUR=0, which means that radio needs to be either in STA, AP or
STA+AP mode (no NONE state available).
Fix ESP AT 1.7 compatibility by keeping radio in STA mode whenever it is
not used.
Move also first AT+CWMODE_CUR invocation before AT+CWDHCP_CUR, so that
the latter executes successfully with ESP AT 1.7.
Fixes: 03ce61004b ("drivers: wifi: esp: control CWMODE depending on
current needs")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Added ap_enable and ap_disable api. The driver will open create an
access point with DHCP Server ip 192.168.1.1 and no security.
Added a small fix for the AF_INET issue.
Added parent and remote to accept routine context.
Added put implementation.
Signed-off-by: Nicolai Glud <nicolai.glud@prevas.dk>
net_context contains both net_sock_type and net_ip_protocol, which are
static during the lifetime of net_context. net_context has basically the
ownership of esp_socket, so we can be sure 'type' and 'ip_proto' are
always accessible through net_context API.
Remove 'type' and 'ip_proto' members from 'esp_socket' structure, as
those are already accessible by net_context API.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Change type of esp_socket->flags from uint8_t to atomic_t, so that read
and write access to those flags is done in atomic (thread-safe) manner.
Introduce esp_socket_ref() and esp_socket_unref() functions, which
operate on atomic refcount variable. esp_socket_ref() role is to
increase refcount if it was already non-zero. If it was zero then NULL
is returned, which means that socket is not used by net_context at the
moment.
Role of refcount:
* socket instance is assured to be between net_offload->get() and
net_offload->put() when refcount > 0,
* makes sure that socket instance can be used (its members can be
dereferenced) when refcount > 0,
* 'context' member is always valid and its members can be dereferenced
when refcount > 0.
esp_socket_get() gets unused socket, as previously. Additionally it sets
refcount to 1 at the end of call, which basically means that from that
point such socket can be referenced by other parts of the driver. Each
esp_socket_get() call should be followed by esp_socket_unref() and
esp_socket_put() to properly invalidate socket and prevent other parts
of driver from using it.
Add ESP_SOCK_WORKQ_STOPPED flag, which is now used to prevent scheduling
more work into driver workqueue. This flag is set in net_offload->put()
callback, so that no more socket work (such as processing RX/TX packets
or closing socket because of errors) is submitted after that.
Introduce mutex lock, which has following role:
* protects dst, connect_cb + conn_user_data, recv_cb + recv_user_data,
* assures that checking ESP_SOCK_WORKQ_STOPPED flag and actually
submitting (or not if net_offload->put was already called) new socket
work to workqueue is done in atomic way.
As there is a mechanism to prevent submitting new work items to
workqueue when net_offload->put() has been executed, then there is no
need to explicitly call esp_socket_ref() in esp_workq thread. This is
because one reference is being held by net_context (after calling
net_context->get()). This is why all the esp_socket_in_use() were simply
dropped. Code running from esp_rx thread on the other hand always uses
esp_socket_ref_from_link_id() helper function (which is backed by
esp_socket_ref()), so that it replaces previous esp_socket_in_use()
calls and additionally makes sure that socket stays valid ("in use")
until esp_socket_unref() is called.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far a dedicated FIFO was used for all RX packets, which was consumed
in single submitted work. This work was also responsible for closing
socket and notifying uppper network layers if some errors occurred
previously or socket was simply closed by peer. There is however a
potential race condition in scenario described below:
esp_rx thread | esp_workq thread
--------------------------|-----------------------------
| ---- esp_recv_work ----
| handle RX packets from FIFO
|
---- on_cmd_ipd ---- |
put new RX packet to FIFO |
---- on_cmd_ipd ---- |
|
---- on_cmd_closed ---- |
mark socket as closed |
---- on_cmd_closed ---- |
|
| handle close
| ---- esp_recv_work ----
In this case we assume that esp_workq was preempted just after
processing all RX packets from FIFO and before checking if socket was
closed. In such scenario RX packet put to FIFO just before doing close
is going to be unhandled, so application layer will miss part of the
data.
Change the way RX packets are scheduled to workqueue, by using the
already available net_pkt->work objects (used for example in native TCP
stack). Create a separate work for closing connection. As a result all
RX packets and close handlers are on the same queue and there is no risk
of handling close events before handling all previously received data.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There might be some scheduled work related to socket currently requested
to be destroyed/closed. Schedule a dummy work to make sure all
previously running work items in workqueue are finished.
When talking about TX packets, this makes sure that all previously
scheduled data is actually sent (flushed) before closing socket.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
It is enough to initialize work structures once during driver init,
because work handlers do not change during driver lifetime.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Currently there are two code paths when sending packets:
asynchronous (using workqueue) when zero timeout was specified and
synchronous in other cases. This doesn't seem to be justified, so
convert code to always schedule packet sending using workqueue.
Each net_pkt has an embedded work item, so use it instead of esp socket
specific work that was shared across all sent packets. This gives a
possibility to schedule multiple packets for sending.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Callback and user data are saved in net_context structure. Those members
are used by native networking stack (net_if), so simply follow the same
pattern.
First of all this allows to reduce runtime information for driver socket
instance. Second and most important benefit is that it allows to move
send handling entirely to workqueue thread.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
ESP chip send number of available RX data using
+IPD=<sock>,<avail_bytes> command. This exact number (truncated to MRU)
was used to read data with AT+CIPRECVDATA=<sock>,<num_of_bytes>.
Use always MRU when sending AT+CIPRECVDATA=<sock>,<mru> request. When
there are less bytes available, then +CIPRECVDATA will just return less
bytes, which is fine for the driver.
There are two advantages to this new behavior:
* there is no need to follow how many bytes were notified by +IPD
message, thus reducing implementation size,
* when data is constantly received by ESP chip, then the last number of
bytes notified by +IPD is no longer up-to-date when sending a
AT+CIPRECVDATA; always requesting MRU number of bytes allows to
always receive maximum currently available number of bytes buffered
by ESP chip.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Dump of communication between ESP chip and Zephyr shows that
+IPD:<sock>,<bytes_avail> is always received after +CIPRECVDATA. This
means that we don't need to update sock->bytes_avail in esp_workq
thread. Additionally there is no need to schedule next AT+CIPRECVDATA
request, as that will be done by +IPD handler anyway.
Relying on +IPD to be received after each +CIPRECVDATA (as long as there
is some more data to be received) allows to simplify operations on
sock->bytes_avail. From now on only esp_rx thread will update its value
and schedule AT+CIPRECVDATA in esp_workq thread. Then in
sock->bytes_avail will be treated as "readonly" in esp_workq
thread. This allows to prevent race condition when both esp_rx and
esp_workq threads could potentially update value of sock->bytes_avail
value at the same time.
<sock>,CLOSED message is received always after retrieving all data from
ESP chip (using AT+CIPRECVDATA), so there is no need to check whether
there are more bytes to be received before marking socket as closed in
Zephyr driver.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Deduplicate final part of RX data processing for two supported cases:
passive (+CIPRECVDATA) and non-passive (+IPD). Move implementation to
esp_socket module, as this is strictly related to socket.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Split +IPD message handling into smaller logical functions, so it is
much easier to follow code and further improve it. Make sure to do as
much parsing work as possible, before accessing esp_socket object. This
will allow to introduce thread-safety locking just in the critical parts
in subsequent commits.
Prefer early return from function over goto to return instruction,
whenever cleanup code is not needed.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Current on_cmd_ciprecvdata handler is a bit overwhelming to follow.
Add a cmd_ciprecvdata_parse() helper, which is responsible only for
parsing received metadata (message offset and length), leaving socket
instance untouched.
Consume received payload later on, just after verifying that socket is
in valid state.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
After a synchronous (timeout > 0) connection attempt was made, it was
being checked if there is some packet to be sent. If positive, then a
send work was queued.
This behavior makes little sense, as TCP connection is not even
considered established at this point (from net_context perspective) if
function has not returned yet. Additionally it differs from
asynchronous (timeout == 0) connection attempt. In case of UDP (and
calling esp_connect() from esp_sendto()) sock->tx_pkt is assured to be
NULL. Drop this piece of code as it doesn't seem to be justified.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2 (out of 3) components used CONFIG_WIFI_LOG_LEVEL, while the last one
didn't specify explicit log level. Always use CONFIG_WIFI_LOG_LEVEL in
all components.
While at it switch to LOG_MODULE_REGISTER(<module>, <log_level>), which
is a more compact way to define log level.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Calculate size based on the real message, instead of assuming some
arbitrary size. This consumes slightly less stack space, but more
importantly gives an idea what has been taken into account when
calculating the size.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
+IPD,<sock>,<bytes_avail> command in passive mode notifies about ESP
internal buffer usage level. Hence value of <bytes_avail> can exceed
4 digit value, which currently results in failure.
+IPD message is used in driver only for scheduling AT+CIPRECVDATA
command and actual value of <bytes_avail> doesn't really
matter. Increase maximum supported value that can be received from
9999 (maximum 4 digits) to 4294967295, which is maximum value of 32-bit
unsigned integer.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Set NET_CONTEXT_CONNECTED when stream socket got connected. This fixes
TCP connection when using eswifi WiFi driver, which got broken after
sockets layer started to validate net_context connection state before
allowing to receive any data.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Set NET_CONTEXT_CONNECTED when stream socket got connected. This fixes
TCP connection when using winc1500 WiFi driver, which got broken after
sockets layer started to validate net_context connection state before
allowing to receive any data.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Set NET_CONTEXT_CONNECTED when stream socket got connected. This fixes
TCP connection when using ESP WiFi driver, which got broken after
sockets layer started to validate net_context connection state before
allowing to receive any data.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far ESP chip was configured directly into STA mode. This works fine,
but consumes lots of power because of enabled WiFi radio, even when it
is not actively used.
Enter NONE mode during initialization, so WiFi radio will be
disabled. Switch between NONE, STA, AP and STA+AP modes depending on
what driver is currently doing (e.g. enable STA only when scanning,
connecting and being connected to AP).
AT+CWAUTOCONN=0 command fails when in NONE mode, so workaround that by
entering temporarily into STA and then switching back to NONE.
Add also a warning log when switching mode was not successful, to ease
debugging possible issues.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
AT+CWMODE command controls in which mode (NONE, STA, AP, STA+AP) ESP
chip is operating. Add helper macros to replace usage of magic
numbers (0-3), hence improve readability. Add also a esp_mode_switch()
helper function, which allows to conveniently switch to chosen mode.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Change internal API operating on ESP driver flags to support multiple
bitwise ORed flags at once. This allows to improve resulting code when
multiple flags are read or modified at once.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
All except one invocations of modem_cmd_send() pass the same interface,
command handler and semaphore. Create a helper function in order to make
invocations slightly more readable.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Both 'cb' and 'user_data' parameters for send/sendto were saved as
'send_cb' and 'send_user_data' members in socket information. None of
them are actually used, so drop them.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Constifying global data allows to save lots of RAM. Defining data inside
function as 'static const' allows on the other hand to save stack usage
and reduced code size (because data doesn't have to be copied on stack
in runtime).
This improvement allows to save 640 bytes of RAM and 64 bytes of ROM
when compiled on ARM.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Configure hostname by issuing AT+CWHOSTNAME="<hostname>" command. Do it
just after setting link address, which is used to generate hostname
postfix when CONFIG_NET_HOSTNAME_UNIQUE=y.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
- Add ESP DHCP Support
- Add ESP Static IP Support including
KConfig entries for configuring IP,Gateway and netMask
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
So far there was 100ms timeout on allocation of RX net_pkt. This is too
little for cases when lots of data are incoming on pretty
fast (e.g. 1Mbps) UART interface and application layer does not consume
received network packets fast enough. Up to now in such cases all
incoming data was processed from UART and there was no data loss when
utilizing hardware flow control. However there was high chance that data
processed from UART could not be passed further to network stack,
because of the 100ms net_pkt allocation timeout. This happens for
example when low priority application does not have enough time to run.
Increase default RX net_pkt allocation timeout from 100ms to 5s, so
there is much more time to process network packets. Such timeout should
not harm, because only a dedicated RX thread will be suspended for that
time, resulting in suspending UART traffic if hardware flow control is
supported.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is now a hardcoded 100ms timeout on allocating new net_pkt for
received data. Move that configuration to Kconfig, so that value can be
tuned according to application needs.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is no reason to keep active stream socket when there was some data
loss. Mark such socket for closing and close it when all (so far)
received packets have been processed.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add uart bus interface to extended esWIFI driver. This enables all
Inventek modules with IWIN AT Commands firmware.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
The WIFI_ESWIFI_NAME config would be uselful when there is no device
tree alternative. The esWIFI driver already is on device tree and the
label property exists. This remove WIFI_ESWIFI_NAME Kconfig variable
and switch to device tree equivalent.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Remove global access to structure eswifi_spi_data variable. Instead,
add a method to pass access to that structure. This allows better
control to the data bus variable.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
All net_bufs allocated to modem_cmd_handler's data->rx_buf are consumed
synchronously in esp.c in the same thread. This means that allocating
them with timeout makes no sense, because timeout will *always* be hit
when there are no more buffers in net_buf_pool.
Get rid of the unnecessary timeout, as it doesn't help and just slows
down processing of incoming data, increasing possibility of data
overrun.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far a dedicated buffer was used for data read from modem
interface. New net_bufs were allocated and filled later, which means
that data was lost when no more net_bufs were available in the pool.
Prevent data loss by allocating net_buf before attempting any read on
modem interface. Process incoming data in a loop as long as reading from
interface results in new data. Also remove dedicated buffer
(data->read_buf) and directly fill net_buf content instead. As a side
effect there are less memory copy operations and RAM usage is reduced.
Pre-allocated net_buf is now always appended to data->rx_buf. When there
was no (more) data read from interface to such net_buf, then this empty
net_buf will be on the end of data->rx_buf fragment list. Update
skipcrlf() and findcrlf() implementations to explicitly check for each
net_buf length, instead of blindly assuming them to have at least single
byte.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Listen func goes through a chain of calls to call winc1500_accept.
This is done to install the accept callback and should not block.
This fixes#28953 where winc1500 driver blocks on listen.
Signed-off-by: Nicolai Glud <nicolai.glud@prevas.dk>
Add power-gpios device-tree binding property to power on module before
communicating with it. This pin is called CHIP_PU in case of ESP32{,-S2}
and CHIP_EN in case of ESP8266. Dedicated reset pin is available only on
the latter, however Espressif recommends (in ESP8266 Hardware Design
Guidelines) to use CHIP_EN instead. Follow those recommendations and use
power-gpios to reset chip if that is provided over device-tree.
Configure power-gpios and reset-gpios as inactive by default, so that
chip becomes ready after executing esp_reset() function, either if one
or both are provided over device-tree.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Most DT bindings use reset-gpios name when there is a pin to reset whole
chip. Rename wifi-reset-gpios to reset-gpios to be more consistent
between various drivers. Additionally this prevents confusion, as
somebody might think that this pin resets only WiFi, which is not true.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
If HW flow control is enabled, then modem_context framework won't drain
UART FIFO blindly, but will stop when there is no more space in RX
ring_buf. This prevents data loss by "pausing" incoming data on hardware
level.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This API allows to drop use of preallocated isr_buf. Most importantly as
a result RAM usage is reduced for each driver utilizing modem_context
framework. Additionally there is less copying done in ISR context, as
data is direcly read from UART FIFO to ring_buf.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Allow to reconfigure UART baudrate on ESP and on host MCU, so a
non-default baudrate can be used for communication. This option helps
for example to increase network bandwidth without touching ESP chip
firmware.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add Kconfig options to configure modem command handler buffer size and
count. This will allow to fine tune those based on UART baudrate, system
load and available memory.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add new Kconfig option to configure modem UART interface handler ring
buffer size. This will allow to lower ring buffer to save some resources
or increase it in case high network bandwidth is utilized (with high
UART baudrate).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reimplement getaddrinfo to call SlNetUtil_getAddrInfo from the TI HAL
for a more robust implementation that supports both client and server
modes, and performs better error-checking.
Fixes#11890
Signed-off-by: Vincent Wan <vwan@ti.com>
The value from socket() was directly assigned to offload_context, which
was treated as a unsigned integer when compared. This prevented the
following if statement from catching any errors, leading to random RAM
access. This is fixed by using an intermediate with the same type as the
return value, which is then assigned to offload_context after error
checking.
Signed-off-by: Abram Early <abram.early@gmail.com>
When offloading only ZSOCK_POLLIN and DNS_EAI_MEMORY are available, so
use those instead of the standard ones.
Fixes#28069.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Schedule read work every 100ms for better latency.
Reschedule read work directly in case of a packet is received
(fast dequeue).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Passing the device's data was sufficient as only the data is being used
by the thread.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Remove non necessary eswifi lock/unlock in read procedure (eswifi
lock support nesting).
Return NULL packet in case socket is closed by remote (tested with
net shell and net recv).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Variable "sd" is no longer referenced after refactoring in 2ed6b6a8ed.
It caused warning-as-error when building using sanitycheck, e.g. in CI.
This is 2nd fixed of the above refactor, after eb9a18432.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
PR #27485 introduced new implementations for close() that do not build
correctly. This commit fixes the problem by re-implementing them.
Fixes#27587
Signed-off-by: Vincent Wan <vwan@ti.com>
Do not route close() calls via ioctl() as that is error prone
and quite pointless. Instead create a callback for close() in
fdtable and use it directly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
unsigned byte value is initialized to -1 and so never satisifies
the while condition, leading to broken ipv4 parsing (dead code).
Fix this by making byte value signed.
Reported by coverity #27326.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
There are possible buffer overflows when parsing the ip address and
SSID. Ensure that we never overwrite the ip and SSID buffers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
There are multiple CID errors all based on the test of
'socket > ESWIFI_OFFLOAD_MAX_SOCKETS'. The test needs to
be '>=' in all cases.
Fixes: #27138Fixes: #27139Fixes: #27140Fixes: #27141Fixes: #27142Fixes: #27143
Signed-off-by: David Leach <david.leach@nxp.com>
When CONFIG_POSIX_API is set in lieu of CONFIG_NET_SOCKETS_POSIX_NAMES,
some macros such as POLLIN, POLLOUT and MSG_PEEK are undefined, and
the appropriate posix headers need to be included to access those.
Signed-off-by: Vincent Wan <vwan@ti.com>
Fix compilation warnings when CONFIG_NET_SOCKETS_OFFLOAD enabled
warning: passing argument 5 of '__eswifi_socket_new' makes pointer
from integer without a cast [-Wint-conversion]
395 | idx = __eswifi_socket_new(eswifi, family, type, proto, 0x50CE);
| ^~~~~~
| |
| int
eswifi.h:137:21: note: expected 'void *' but argument is of type 'int'
137 | int proto, void *context);
| ~~~~~~^~~~~~~
In function 'eswifi_socket_bind':
warning: comparison between pointer and integer
461 | if ((addrlen == NULL) || (addr == NULL) ||
|
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
use common log module across all eswifi sources, which allows
to compile with CONFIG_NET_SOCKETS_OFFLOAD.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
It can happen that the command '>' is received between
modem_cmd_send_nolock and modem_cmd_handler_update_cmds. Since the
command handler for '>' is not set, sem_tx_ready will not be given
and _sock_send will timeout. Make sure the command handlers are set
before the send by also passing them to modem_cmd_send_nolock.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
IPv6 support was not fully implemented in the driver and was disabled.
This commit completes the implementation and enables it when
configured.
Signed-off-by: Vincent Wan <vwan@ti.com>
Fix typo in logged Kconfig option name that is missing in used
configuration. This one was mostly problematic for developers wanting to
find such option in source tree using grep - NET_SOCKET_OFFLOAD was not
found in Kconfig files.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
wifi-reset-gpios flags were not respected so far. This means that
setting reset as active low (which is required in most cases for ESP
modules/chips) was done inside esp driver with inverted logic. Use dts
flags instead, so "active low" property is configured the same way as
for other drivers (i.e. in device-tree instead of driver).
This change also allows to configure reset as active high, in case where
ESP's nRST signal is somehow inverted on the board (behaving as RST
signal instead).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
