This patch adds support for PWM blink which is found in intel's
PCH hardwares.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Current erroneous usages of dma-channels prop by lpc-dma nodes:
* dma-channels devicetree property should describe the number of
channels supported by the dma controller, not the number of channels
in use.
* LPC55SXX and RTXXX SOCs should be setting dma channels prop at SOC
level, not board level, since it is an SOC property, not a board
property.
* lpc55s28 has 23 channels for dma0, not 20.
* lpc55s28 has 10 channels for dma1, not 0.
* lpc55s69 has 23 channels for dma0, not 20.
* rt5xx has 37 channels for dma1, not 0.
* rt6xx has 33 channels for dma0, not 20.
* rt6xx has 33 channels for dma1, not 0.
Fix all of these issues
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Set the DMA number of otrigs DT property at the SOC level instead of the
board DTS because it is an SOC property and does not change on different
boards.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add I2C target driver used buffer mode. The maximum accessible buffer
is 2044 bytes, the default is 256 bytes.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add basic device tree description fro stm32wba soc series.
This includes Flash/RAM clocks and clock control nodes
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add support of r8a77961 SoC to gen3 series.
Create a dtsi file with a common part for both r8a77951 and r8a77961.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\xmc47_relax_kit board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Adding support for the adafruit can picowbell shield for the
raspberry pi picoi. Also added nodelable for spi0 called 'pico_spi'
as well as an GPIO nexus node 'pico_header'
Signed-off-by: Joseph Yates <joeyatessecond@gmail.com>
This change introduces the "_rtc_timer" suffix for the system tick timer
driver "compatible" property and aligns naming conventions with the
actual CC13/26xx SoC series product policy.
This frees up the "_rtc" namespace to introduce additional APIs based on
the same peripheral in the future (not part of this PR):
rtc: rtc@... {
compatible = "ti,cc13xx-cc26xx-rtc";
...
timer {
compatible = "ti,cc13xx-cc26xx-rtc-timer";
...
};
counter {
compatible = "ti,cc13xx-cc26xx-rtc-counter";
...
};
pps {
compatible = "ti,cc13xx-cc26xx-rtc-pps";
...
};
};
Or alternatively an MFD pattern with similar requirements.
Fixing the namespacing now makes sense standalone as it reduces the
chance of custom drivers being broken in the future.
Redundant extension of the mandatory system clock devicetree node is
replaced with a single `status = "okay"` which seems to be the more
sensible default to avoid user error when defining custom boards.
Knowledgeable users can still override this if really needed.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Removes duplicate code and inconsistencies in the naming of the
cc13xx_cc26xx devicetree and RTC driver hierarchy and alignes it with
the actual TI product series naming hierarchy.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Add SHA256 accelerator support for it8xxx2 series.
This driver passes the following test:
tests/crypto/crypto_hash/
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Changes rshunt-milliohms to rshunt-micro-ohms allowing for current
sensing of greater than 16.4A (1mOhm resistor). This is commonly
set to 100 uOhm for VMU/FMU boards/applications.
Co-authored-by: James Goppert <james.goppert@gmail.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
The different references manuals of the STM32H7 family (RM099, RM0433,
RM0445 and RM0468) states that SDMMC2RTS and STMMC2EN are on bit 9 of
respectively RCC_AHB2RSTR and RCC_AHB2ENR (not on bit 8). Fixes the stm32h7
dts accordingly.
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
Reuse existing MCUX-based shim driver for LPUART that is compatible with
the hardware block in S32K344. DMA is not yet supported.
Use the board's debug connector (P6 / LPUART2) as default console.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
SIUL2 may require multiple interrupt handlers instead of a single one as
currently supported for S32Z/E. This is needed to enable support on
S32K3.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Support pin control for NXP S32K3 devices and enable it by default on
mr_canhubk3 board configuration.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The clock controller is a singleton controller for all the system-level
clocks (XOSC, PLL, CGM, etc) to provide run-time information to the
peripheral device drivers about the module's clocks.
Clock configuration is not yet supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The S32K3 MCUs are 32-bit Arm Cortex-M7-based microcontrollers with a
focus on automotive and industrial applications. The S32K344 features
a lock-step core, internal flash, RAM and TCM with ECC.
Co-authored-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Co-authored-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add a small delay between reading the transport header and reading the
HCI data. Failing to do so on a nRF9160<->nRF52832 link was reliably
resulting in the nRF9160 trying to read data before the nRF52832 had
set up the SPI transaction, resulting in the host reading a buffer full
of 0x00 and having to run the entire read result again.
Transceiving a 10 byte packet takes at least 31uS, while 100 byte
packets are around 150uS (duration of `spi_transceive` call). Waiting
1 tick to eliminate the need for most retransmissions is a valid
tradeoff.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add an option that signifies that the ESP modem may be reset at the same
time as the SoC by an external source. When this is the case, we first
wait for an unsolicited "ready" message from the modem, before
attempting to reset the device. This prevents two initialisation
sequences attempting to run at the same time.
We still want to wait for the complete initialisation sequence to
complete before returning in this case.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This adds support for the TIMER1-4 counter.
Each counter has 24bits and can run on LP_CLK (15-32KHz)
or DIVN clock (32MHz) with prescaler 1-32.
Each counter can have one alarm set.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
The display controller supports software reset and the driver already
implements it. Therefore it's not necessary to require a reset gpio in
device tree.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Remove `clocks` property for fixed-clock binding.
A fixed-clock should not have an input clock, since by
definition it's an always on fixed-rate clock.
Signed-off-by: Moritz Fischer <moritzf@google.com>
This adds a driver for Texas Instruments Cost-Optimized, Ultra-Small,
12-Bit, System-Monitoring ADCs. Currently only TLA2021 is supported,
TLA2022 and TLA2024 may follow based on this driver.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
