This adds timer driver for Renesas SmartBond(tm) family.
It uses TIMER2 block which is in PD_TIM power domain so it can work even
if ARM core is disabled, thus can work as a sleep timer.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This commit addst support for the system timer peripheral which
can be found in Apollo4 SoCs.
Signed-off-by: Maciej Sobkowski <msobkowski@antmicro.com>
Removes duplicate code and inconsistencies in the naming of the
cc13xx_cc26xx devicetree and RTC driver hierarchy and alignes it with
the actual TI product series naming hierarchy.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
- Add Gecko BURTC sys_clock driver to handle wake up from EM2,3 states
- Remove custom PM policy and dependency on HAL sl_power_manager service
- EM1 supported in all configurations
- EM2,3 supported only if SysTick is replaced by BURTC
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add dependency on SYS_CLOCK_EXISTS to all timer configurations.
This would avoid a situation where a possible timer configuration would
be wrongfully selected but SYS_CLOCK_EXISTS is disabled.
This simplifies code that wants to check for system clock capabilities
don't have to check if the system clock exists in addition.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Spin locks held for any lengthy duration prevent interrupts and
in a real time system where interrupts drive tasks this can be
problematic. Add an option to assert if a spin lock is held for
a duration longer than the configurable number of microseconds.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Added a driver to enable the GPT timer on RT1xxx parts to be used
instead of systick as a clock source. The timer is set to run in reset
mode, and uses the low frequency 32kHz oscillator for power savings
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
- Remove the weak symbol definition
- Notify about the capability of disabling via a selected Kconfig option
(CONFIG_SYSTEM_TIMER_HAS_DISABLE_SUPPORT)
- Provide a dummy inline function when the functionality is not
available
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Split Kconfig into individual files for each driver. This improves
overall readability of the Kconfig options.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This change adds `k_cycle_get_64()` on platforms that
support a 64-bit cycle counter.
The interface functions `arch_k_cycle_get_64()` and
`sys_clock_cycle_get_64()` are also introduced.
Fixes#39934
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Modification of the ARM architected timer driver and its configuration
data in order to address an erratum which exists at least in the Cor-
tex-A9 CPU, and which can also be observed in the QEMU implementation
of the Cortex-A9.
Comp.: ARM Cortex-A9 processors Software Developer Errata Notice
ARM document ID032315
Erratum 740657
This erratum causes a spurious interrupt pending indication with the
interrupt controller if no new compare value is written within the
timer ISR before the interrupt is cleared. This is usually the case
in tickless mode. If the spurious interrupt is not prevented, the
timer ISR will be called twice, but on second execution, the pending
flag is not set within the timer's register space. Not handling this
issue will lead to erratic tick announcements to the kernel.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Add config macro to set interrupt as level triggered for ARM CPUs
Merge all timer configures into one place, then no need to overwrite
hpet_timer_conf_get/set() functions in SoC layer
Make hpet_timer_comparator_set() as the only register access function
to implemented in the SoC layer
Signed-off-by: Dong Wang <dong.d.wang@intel.com>
This allows the HPET timer to use kconfig to specify clock
frequency instead of relying on calculation at runtime.
When the frequency is known at build, this allow the toolchain
to optimize some calculations.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add NXP Kinetis Low Power Timer (LPTMR) OS timer driver shim. Since the
LPTMR does not support asynchronous changes to the timer period, only
non-tickless mode is supported.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
by adding the soc specific files such: soc initialization code,
linker scripts and support for esp32c3 devkitm
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
Make the APIC_TIMER_IRQ_PRIORITY Kconfig depend on APIC_TIMER ||
APIC_TSC_DEADLINE_TIMER to hide it in menuconfig when not applicable.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Modern hardware all supports a TSC_DEADLINE mode for the APIC timer,
where the same GHz-scale 64 bit TSC used for performance monitoring
becomes the free-running counter used for cpu-local timer interrupts.
Being a free running counter that does not need to be reset, it will
not lose time in an interrupt. Being 64 bit, it needs no rollover or
clamping logic in the driver when presented with a 32 bit tick count.
Being a proper comparator, it will correctly trigger interrupts for
times set "in the past" and thus needs no minimum/clamping logic. The
counter is synchronized across the system architecturally (modulo one
burp where firmware likes to change the adjustment value) so usage is
SMP-safe by default. Access to the 64 bit counter and comparator
value are single-instruction atomics even on 32 bit systems, so it
beats even the RISC-V machine timer in complexity (which was our
reigning champ for "simplest timer driver").
Really this is just ideal for Zephyr. So rather than try to add
support for it to the existing APIC driver and increase complexity,
make this a new standalone driver instead. All modern hardware has
what it needs. The sole gotcha is that it's not easily emulatable
(qemu supports it only under kvm where they can freeload on the host
TSC) so it can be exercised only on hardware platforms right now.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Compare Match Timer is a 32 bit compare match timer
that can be found on various Renesas R-Car SoC.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Add initial support for the Cortex-M55 Core which is an implementation
of the Armv8.1-M mainline architecture and includes support for the
M‑profile Vector Extension (MVE).
The support is based on the Cortex-M33 support that already exists in
Zephyr.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This feature predated the tickless kernel and has been in legacy mode
for a while. We now have no drivers or systems that do not support
tickless, so remove this option and cleanup the code to only use
tickless.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is another API that is being used in all timer drivers and is not
internal to the clock subsystem. Remove the leading z_ and make promote
it to a cross-subsystem API.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The clock/timer APIs are not application facing APIs, however, similar
to arch_ and a few other APIs they are available to implement drivers
and add support for new hardware and are documented and available to be
used outside of the clock/kernel subsystems.
Remove the leading z_ and provide them as clock_* APIs for someone
writing a new timer driver to use.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL introduces a kernel device driver implemented by the internal
64/32-bit timers in Nuvoton NPCX series. Via these two kinds of timer,
the driver provides an standard "system clock driver" interface.
It includes:
- A system timer based on an ITIM64 (Internal 64-bit timer) instance,
clocked by APB2 which freq is CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC.
- Its prescaler is set to 1 and provide the kernel cycles reading
without handling overflow mechanism.
- A event timer based on an ITIM32 (Internal 32-bit timer) instance,
clocked by LCLK which frequency is 32KHz and still activated when ec
entered "idle/deep idle" power state for better power consumption.
- Its prescaler is set to 1 and provide timeout event mechansim.
- Compensate system timer which clock is gating for better power
consumption after ec left"idle/deep idle" power state.
This CL passed starve, timer_api, and timer_monotonic test suites.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
TICKLESS_CAPABLE is now selectable only and without prompt, so remove it
from _defconfig files and select it directly by the timer.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
For a while now, we've had two APIC drivers. The older was preserved
initially as the new (much smaller, "new style") code didn't have
support for Quark interrupt handling. But that's long dead now. Just
remove it.
Note that this migrates the one board using this driver (acrn) to
CONFIG_APIC_TIMER instead.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This commit is about the it8xxx2 timer driver.
We use the timer 5 as system timer for count time,
so the timer interrupt is trigged by it.
Signed-off-by: Cheryl Su <cheryl.su@ite.com.tw>
Fix TIMER0 and RTC0 being selectable when using out-of-tree Bluetooth
controller.
Generalize the Kconfig to have the features that use the HW peripheral
select them as reserved to make the dependencies more manageable.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Extended nrf_rtc_timer driver to expose API for using RTC for
other purposes. System timer is using one compare channels,
other channels may be used through this API.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This adds support for GRLIB GPTIMER general purpose timer used in
LEON3/4/5 systems.
One of the GPTIMER subtimers is used to generate periodic interrutps
for announcing ticks. Another subtimer is used as upcounter for the
cycle_get_32() service.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
Added configuration for approach to starting system clock source.
There are 3 options: no wait, wait untill available, wait until
stable.
Added support for those modes in clock control driver which handles
low frequency source clock.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Use setting from devicetree to drive the default setting for
CORTEX_M_SYSTICK. We update the dts files to default systick to be
enabled since the major of cortex-m platforms utilize it by default
(except on Nordic SoCs, TI CC13x2/CC26x2 and MEC1501 in which we
default to disabled).
Fixes#25299
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The DSP wall clock timer on some Intel SoC is a timer driven
directly by external oscillator and is external to the CPU
core(s). It is not as fast as the internal core clock, but
provides a common and synchronized counter for all CPU cores
(which is useful for SMP).
This uses the RISCV timer as base as it is using 64-bit
counter.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This commit reworks the Xilinx TTC timer driver to use the "match" mode
instead of the "interval" mode which counts up to the specified value
and resets to zero.
Using the "match" mode ensures that the timer keeps counting even after
an interrupt is triggered, and facilitates the tickless mode support
implementation.
This also allows `z_timer_cycle_get_32` to return the correct cycle
count when interrupt is locked; thereby, fixing the k_busy_wait hang
issue.
Note that the TTC "match" mode emulation (and tickless timer operation)
is only stable when the QEMU icount mode is enabled.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
ARM cores may have a per-core architected timer, which provides per-cpu
timers, attached to a GIC to deliver its per-processor interrupts via
PPIs. This is the most common case supported by QEMU in the virt
platform.
This patch introduces support for this timer abstracting the way the
timer registers are actually accessed. This is needed because different
architectures (for example ARMv7-R vs ARMv8-A) use different registers
and even the same architecture (ARMv8-A) can actually use different
timers (ELx physical timers vs ELx virtual timers).
So we introduce the common driver here but the actual SoC / architecture
/ board must provide the three helpers (arm_arch_timer_set_compare(),
arm_arch_timer_toggle(), arm_arch_timer_count()) using an header file
imported through the arch/cpu.h header file.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
