We no longer plan to support a split address space with
the kernel in high memory and per-process address spaces.
Because of this, we can simplify some things. System RAM
is now always identity mapped at boot.
We no longer require any virtual-to-physical translation
for page tables, and can remove the dual-mapping logic
from the page table generation script since we won't need
to transition the instruction point off of physical
addresses.
CONFIG_KERNEL_VM_BASE and CONFIG_KERNEL_VM_LIMIT
have been removed. The kernel's address space always
starts at CONFIG_SRAM_BASE_ADDRESS, of a fixed size
specified by CONFIG_KERNEL_VM_SIZE.
Driver MMIOs and other uses of k_mem_map() are still
virtually mapped, and the later introduction of demand
paging will result in only a subset of system RAM being
a fixed identity mapping instead of all of it.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It implements gdb remote protocol to talk with a host gdb during the
debug session. The implementation is divided in three layers:
1 - The top layer that is responsible for the gdb remote protocol.
2 - An architecture specific layer responsible to write/read registers,
set breakpoints, handle exceptions, ...
3 - A transport layer to be used to communicate with the host
The communication with GDB in the host is synchronous and the systems
stops execution waiting for instructions and return its execution after
a "continue" or "step" command. The protocol has an exception that is
when the host sends a packet to cause an interruption, usually triggered
by a Ctrl-C. This implementation ignores this instruction though.
This initial work supports only X86 using uart as backend.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
To debug hard-to-reproduce faults/panics, it's helpful to get the full
register state at the time a fault occurred. This enables recovering
full backtraces and the state of local variables at the time of a
crash.
This PR introduces a new Kconfig option, CONFIG_EXTRA_EXCEPTION_INFO,
to facilitate this use case. The option enables the capturing of the
callee-saved register state (r4-r11 & exc_return) during a fault. The
info is forwarded to `k_sys_fatal_error_handler` in the z_arch_esf_t
parameter. From there, the data can be saved for post-mortem analysis.
To test the functionality a new unit test was added to
tests/arch/arm_interrupt which verifies the register contents passed
in the argument match the state leading up to a crash.
Signed-off-by: Chris Coleman <chris@memfault.com>
Saves us a few bytes of program text on arches that don't need
these implemented, currently all uniprocessor MPU-based systems.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The x86 ports are linked at their physical address and
the arch_mem_map() implementation currently requires
virtual = physical. This will be removed later.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If CONFIG_MMU is active, choose whether to separate text,
rodata, and ram into their own page-aligned regions so that
they have have different MMU permissions applied.
If disabled, all RAM pages will have RWX permission to
supervisor mode, but some memory may be saved due to lack
of page alignment padding between these regions.
This used to always happen. This patch adds the Kconfig,
linker script changes to come in a subsequent patch.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This adds the necessary bits in arch code, and Python scripts
to enable coredump support for ARM Cortex-M.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a very primitive coredump mechanism under subsys/debug
where during fatal error, register and memory content can be
dumped to coredump backend. One such backend utilizing log
module for output is included. Once the coredump log is converted
to a binary file, it can be used with the ELF output file as
inputs to an overly simplified implementation of a GDB server.
This GDB server can be attached via the target remote command of
GDB and will be serving register and memory content. This allows
using GDB to examine stack and memory where the fatal error
occurred.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
unify how XIP is configured across architectures. Use imply instead of
setting defaults per architecture and imply XIP on riscv arch and remove
XIP configuration from individual defconfig files to match other
architectures.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This config indicates that a memory management unit is present
and enabled, which will in turn allow arch APIs to allow
mapping memory to be used.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
x86-32 thread objects require special alignment since they
contain a buffer that is passed to fxsave/fxrstor instructions.
This fell over if the dummy thread is created in a stack frame.
Implement a custom swap to main for x86 which still uses a
dummy thread, but in an unused part of the interrupt stack
with proper alignment.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This commit renames the Kconfig `FP_SHARING` symbol to `FPU_SHARING`,
since this symbol specifically refers to the hardware FPU sharing
support by means of FPU context preservation, and the "FP" prefix is
not fully descriptive of that; leaving room for ambiguity.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit reworks the symbol descriptions for `CONFIG_FPU` and
`CONFIG_FP_SHARING`, in order to provide more details and clarify any
ambiguity between the two symbols.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit renames the Kconfig `FLOAT` symbol to `FPU`, since this
symbol only indicates that the hardware Floating Point Unit (FPU) is
used and does not imply and/or indicate the general availability of
toolchain-level floating point support (i.e. this symbol is not
selected when building for an FPU-less platform that supports floating
point operations through the toolchain-provided software floating point
library).
Moreover, given that the symbol that indicates the availability of FPU
is named `CPU_HAS_FPU`, it only makes sense to use "FPU" in the name of
the symbol that enables the FPU.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This change adds full shared floating point support for the RISCV
architecture with minimal impact on threads with floating point
support not enabled.
Signed-off-by: Corey Wharton <coreyw7@fb.com>
This moves enabling XTENSA_HAL to the SoC definitions.
As Xtensa SoCs are highly configurable, it is possible
that the generic Xtensa HAL provided in the tree is
not suitable. So only enable XTENSA_HAL only if
the generic version can be used.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Now that all posix boards have a dts we can move the selection of
HAS_DTS to the arch level like it is for all the other architectures.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This never needed to be put in a separate gperf table.
Privilege mode stacks can be generated by the main
gen_kobject_list.py logic, which we do here.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The existing stack_analyze APIs had some problems:
1. Not properly namespaced
2. Accepted the stack object as a parameter, yet the stack object
does not contain the necessary information to get the associated
buffer region, the thread object is needed for this
3. Caused a crash on certain platforms that do not allow inspection
of unused stack space for the currently running thread
4. No user mode access
5. Separately passed in thread name
We deprecate these functions and add a new API
k_thread_stack_space_get() which addresses all of these issues.
A helper API log_stack_usage() also added which resembles
STACK_ANALYZE() in functionality.
Fixes: #17852
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
All SoCs must now 'select' one of the CONFIG_<arch> symbols. Add an
ARCH_IS_SET helper symbol that's selected by the arch symbols and
checked in CMake, printing a warning otherwise.
Might save people some time until they're used to the new scheme.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Define there options for runtime error handling:
- assert on all errors (ASSERT_ON_ERRORS)
- no runtime checks (no asserts, no runtime error handling)
(NO_RUNTIME_CHECKS)
- full runtime error handling (the default) (RUNTIME_ERROR_CHECKS)
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit addresses the following issues:
1. Add a new Kconfig configuration for specifying Dual-redundant Core
Lock-step (DCLS) processor topology.
2. Register initialisation is only required when Dual-redundant Core
Lock-step (DCLS) is implemented in hardware. This initialisation is
required on DCLS only because the architectural registers are in an
indeterminate state after reset and therefore the initial register
state of the two parallel executing cores are not guaranteed to be
identical, which can lead to DCCM detecting it as a hardware fault.
A conditional compilation check for this hardware configuration
using the newly added CONFIG_CPU_HAS_DCLS flag has been added.
3. The existing CPU register initialisation code did not take into
account the banked registers for every execution mode. The new
implementation ensures that all architectural registers of every
mode are initialised.
4. Add VFP register initialisation for when floating-point support is
enabled and the core is configured in DCLS topology. This
initialisation sequence is required for the same reason given in
the first issue.
5. Add provision for platform-specific initialisation on Cortex-R
using PLATFORM_SPECIFIC_INIT config and z_platform_init function.
6. Remove seemingly pointless and inadequately defined STACK_MARGIN.
Not only does it violate the 8-byte stack alignment rule, it does
not provide any form of real stack protection.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The SRAM address and size are currently available as both
DT_SRAM_{BASE_ADDRESS,SIZE} and as CONFIG_SRAM_{BASE_ADDRESS,SIZE} (via
the Kconfig preprocessor).
Use the CONFIG_SRAM_* versions everywhere, and remove generation of the
DT_SRAM_* versions from gen_defines.py.
The Kconfig symbols currently depend on 'ARC || ARM || NIOS2 || X86'.
Not sure why, so I removed it.
It looks like no configuration files set CONFIG_SRAM_* at the moment, so
another option might be to use the DT_* symbols everywhere instead. Some
Kconfig.defconfig.series files add defaults to them though.
Also improve the help texts for CONFIG_SRAM_* to say that they normally
come from devicetree rather than configuration files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
How prompts work is better documented nowadays, and these comments might
not be that helpful if you don't know.
There are lots promptless symbols that don't have a comment.
Also fix up some comments in arch/Kconfig that seem misplaced/redundant,
and clean up some whitespace (no blank line after a comment makes it
look like it only applies to the symbol directly after it to me).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This adds the necessary bits to build the Xtensa HAL as
a module, and removes the bits to use the HAL built with
the Zephyr SDK.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
When we build without support for user mode, we do not need
a large number of MPU regions, so we should not allow having
MPU_GAP_FILLING unset. This would allow PRIV code execute from
SRAM, which is an unnecessary compromise on ARMv8-M builds
without USERSPACE support. We update the Kconfig dependencies
and add a sentence for clarification.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This API was only created to facilitate testing of kernel
objects in IRQ context, never for actual applications.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We introduce MPU_GAP_FILLING Kconfig option that instructs
the MPU driver to enforce a full SRAM partitioning, when it
programs the dynamic MPU regions (user thread stack, PRIV stack
guard and application memory domains) at context-switch. We
allow this to be configurable, in order to increase the number
of MPU regions available for application memory domain programming.
This option is introduced in arch/Kconfig, as it is expected
to serve as a cross-ARCH symbol. The option can be set by the
user during build configuration.
By not enforcing full partition, we may leave part of kernel
SRAM area covered only by the default ARM memory map. This
is fine for User Mode, since the background ARM map does not
allow nPRIV access at all. The difference is that kernel code
will be able to attempt fetching instructions from kernel SRAM
area without this leading directly to a MemManage exception.
Since this does not compromize User Mode, we make the skipping
of full partitioning the default behavior for the ARMv8-M MPU
driver. The application developer may be able to overwrite this.
In the wake of this change we update the macro definitions in
arm_core_mpu_dev.h that derive the maximum number of MPU regions
for application memory domains.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There are two set of code supporting x86_64: x86_64 using x32 ABI,
and x86 long mode, and this consolidates both into one x86_64
architecture and SoC supporting truly 64-bit mode.
() Removes the x86_64:x32 architecture and SoC, and replaces
them with the existing x86 long mode arch and SoC.
() Replace qemu_x86_64 with qemu_x86_long as qemu_x86_64.
() Updates samples and tests to remove reference to
qemu_x86_long.
() Renames CONFIG_X86_LONGMODE to CONFIG_X86_64.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
We introduce a Kconfig option to signify whether
an Architecture has the capability of detecting
whether execution is, currently, in a nested
exception.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Replace:
dt_chosen_reg_addr
dt_chosen_reg_size
dt_node_reg_addr
dt_node_reg_size
with:
dt_chosen_reg_addr_int
dt_chosen_reg_size_int
dt_chosen_reg_addr_hex
dt_chosen_reg_size_hex
dt_node_reg_addr_int
dt_node_reg_size_int
dt_node_reg_addr_hex
dt_node_reg_size_hex
So that we get the proper formatted string for the type of symbol.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove the
# Omit prompt to signify a "hidden" option
comments that appear on some symbols. They seem to have been copy-pasted
at random, as there are lots of promptless symbols that don't have them
(that's confusing in itself, because it might give the idea that the
ones with comments are special in some way).
I suspect those comments wouldn't have helped me much if I didn't know
Kconfig either. There's a lot more Kconfig documentation now too, e.g.
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Keep some comments that give more information than the symbol having no
prompt.
Also do some minor drive-by cleanup.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Convert how we get the various chosen properties like "zephyr,console"
to use the new kconfig functions like dt_chosen_to_label.
Because of how kconfig parses things we define a set of variables of the
form DT_CHOSEN_Z_<PROP> since comma's are parsed as field seperators in
macros.
This conversion allows us to remove code in gen_defines.py for the
following chosen properties:
zephyr,console
zephyr,shell-uart
zephyr,bt-uart
zephyr,uart-pipe
zephyr,bt-mon-uart
zephyr,uart-mcumgr
zephyr,bt-c2h-uart
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We re-wrote the xtensa arch code, but never got around
to purging the old implementation.
Removed those boards which hadn't been moved to the new
arch code. These were all xt-sim simulator targets and not
real hardware.
Fixes: #18138
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
With the upcoming riscv64 support, it is best to use "riscv" as the
subdirectory name and common symbols as riscv32 and riscv64 support
code is almost identical. Then later decide whether 32-bit or 64-bit
compilation is wanted.
Redirects for the web documentation are also included.
Then zephyrbot complained about this:
"
New files added that are not covered in CODEOWNERS:
dts/riscv/microsemi-miv.dtsi
dts/riscv/riscv32-fe310.dtsi
Please add one or more entries in the CODEOWNERS file to cover
those files
"
So I assigned them to those who created them. Feel free to readjust
as necessary.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The ARM specific _impl_k_thread_abort function only applies to Cortex-M
so move it to the cortex_m specific directory.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
* z_NanoFatalErrorHandler() is now moved to common kernel code
and renamed z_fatal_error(). Arches dump arch-specific info
before calling.
* z_SysFatalErrorHandler() is now moved to common kernel code
and renamed k_sys_fatal_error_handler(). It is now much simpler;
the default policy is simply to lock interrupts and halt the system.
If an implementation of this function returns, then the currently
running thread is aborted.
* New arch-specific APIs introduced:
- z_arch_system_halt() simply powers off or halts the system.
* We now have a standard set of fatal exception reason codes,
namespaced under K_ERR_*
* CONFIG_SIMPLE_FATAL_ERROR_HANDLER deleted
* LOG_PANIC() calls moved to k_sys_fatal_error_handler()
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
sw_isr_table has two entries, an argument and an ISR function. The
comment on struct _isr_table_entry in include/sw_isr_table.h says that
"This allows a table entry to be loaded [...] with one ldmia
instruction, on ARM [...]". Some arch, e.g. SPARC, also has a double
word load instruction, "ldd", but the instruct must have address align
to double word or 8 bytes.
This commit makes the table alignment configurable. It allows each
architecture to specify it, if needed. The default value is 0 for no
alignment.
Signed-off-by: Yasushi SHOJI <y-shoji@ispace-inc.com>
The libc hooks for Newlib requires CONFIG_SRAM_SIZE and
the symbol "_end" at the end of memory. This is in preparation
for enabling Newlib for x86_64.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
