The DRAM range 0xc0000000~0xcfffffff is reserved for the Ethos-U NPU,
so change the RAM base to 0xd0000000.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
remove legacy modem properties and add modem node
compatible to modem subsystem, rak5010_nrf52840
has two variant, one with BG95-M3 and other is
BG96 modem, both are pin to pin compatible.
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Define the reg and size property for the stm32 disco kits
which have an octospi instance
Refer to the dts/bindings/flash_controller/st,stm32-ospi-nor.yaml.
Also remove the <size> property for the stm362h750 disco kit.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Display is not working on STM32F429i-DISC1 board because
display_blanking_off() needs to be sent to ILI9341 device, but it's sent
to LTDC instead which does not implement it.
This patch adds a LTDC DT property that provides the pHandle of the
display's own controller so that display_blanking_off/on are forwarded to
it when they are called by an application.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Add a board that allows to build for the nRF54H20 PPR RISC-V core.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Because both, RISC-V and ARM cores share the same pinctrl driver. The
top level common folder will disappear with the introduction of HWMv2,
where multi-arch SoCs will be well supported.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add targets that allows building for the Application and Radio cores
in the nRF54H20 SoC on the nRF54H20 PDK board.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The mailbox peripheral is actively accessed by stm32_hsem functions,
so mark the device as enabled in DTS.
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
Define the reg and size property for the stm32 boards with qspi inside
Refer to the dts/bindings/flash_controller/st,stm32-ospi-nor.yaml.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Define the reg and size property for the stm32u585 and stm32l562
disco kit.
Refer to the dts/bindings/flash_controller/st,stm32-ospi-nor.yaml.
The stm32l562 reads the sfdp table from the flash itself.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
1. Configure 'core-clock' to 192MHz to generate necessary 48MHz
2. Support workaround to disallowing ISO IN/OUT EPs to be assigned
the same EP numbers
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
drivers: eth: phy: tja1103: Handle link change
These changes enable -
TJA1103 driver to gracefully handle Link connect or disconnect events
between Ethernet PHY and its link partner and notify it to the
upper network layers
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
The DMA is already enabled for this board, but updating the board doc
page to make that clear, and enabling the DMA loop_transfer test.
Signed-off-by: Derek Snell <derek.snell@nxp.com>
GR716A has two SPIMCTRL SPI controllers.
This adds the SPIMCTRL description to the DTS and makes the SPI
option available in the kernel configuration.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
Add support for ADI EVAL-ADIN2111EBZ.
Tested samples:
* hello_world
* blinky
* dhcpv4_client
Co-developed-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Add support for ADI EVAL-ADIN1110EBZ.
Tested samples:
* hello_world
* blinky
* dhcpv4_client
* adt7420
Tested proper SPI detection of the ADIN1110 chip.
Co-developed-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Microchip's PolarFire SoC interface with on-board spi
nor flash via system controller. This on-board spi nor flash can be
used to store FPGA design bitstream's.
Signed-off-by: Harshit Agarwal <harshit.agarwal@microchip.com>
qemu_x86_tiny@768 has coverage enabled by default. Because of
this, it requires more stack space for running tests.
The increases needed are verified via twister.
Fixes#68272
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert ili9xxx display drivers to use MIPI DBI API. Due to the fact
this change requires a new devicetree structure for the display driver
to build, required devicetree changes are also included in this commit
for all boards and shields defining an instance of an ili9xxx display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
add acpi pnp/hw id for pcie node to enable support for retreive
interrupt routing information for pci legacy interrupt via acpi
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
We need to enable this configuration for all R-Car ARM64 boards.
First and foremost, we definitely should run Zephyr on the boards
in the NS-EL1 state. The EL3 is used for TF-A, EL2 is used for
U-Boot, and Xen in the case when we run Zephyr as Dom-0. The S-EL1
is used for OP-Tee, and S-EL0 is used for OP-Tee apps.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
On the Polarfire SOC Icicle Kit the SPI pins are routed to MikroBus.
Enable SPI by default.
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
the device tree offers a default config (qdec0) for 1x qdec at TC0,
however does not offer a default config for qdec1 - qdec3.
this will be added with this commit. Fixes#65610
Signed-off-by: Sven Ginka <sven.ginka@gmail.com>
The purpose of this separation is to avoid conflict initializing
gpio-keys because button 0 and joystick up have a shared interrupt
source. Joystick is now configured using polling mode option.
Signed-off-by: Joel Guittet <joelguittet@gmail.com>
This allows to run tests & examples on the physical board with:
```
west twister -p mps2_an521 --device-testing --device-serial /dev/ttyUSB0
```
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Create a folder for RZ Renesas range device tree to follow how it's
done for other renesas ranges.
It will also help to better delimit areas to maintain.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
- Remove hadcoded cc2538-bsl.py path
- Use cc1352-flasher program instead
- Add docs about how to install the program
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
This commits makes it possible to use the onboard bluetooth
module (STM32WB5MMG) with existing zephyr bluetooth samples.
Note that there was no hardware flow control wiring
available on the board, which is why it has been disabled
in the both main board and BLE module Device Tree. As the
board doesn't support HW flow control, users must set
CONFIG_BT_HCI_ACL_FLOW_CONTROL=n in project files.
Signed-off-by: Javad Rahimipetroudi <javad.rahimipetroudi@mind.be>
This patch introduces the Bluetooth Low Energy (BLE) feature to the board.
The board utilizes the STM32WB5MMG as the BLE module. However, As there
was no BLE controller available for this module. Therefore, a board
support package has been added to enable the STM32WB5MMG module to act as
a BLE controller. This is achieved by running Zephyr's hci_uart example on
the STM32WB5MMG module which enables communication with the main
microcontroller over the H:4 HCI transport protocol. So, users must first
build the BLE controller for the BLE module and upload it via on board
ST-Link,then they can uses Zephyr Bluetooth demos on the development board
Note that there was no hardware flow control wiring available on the
board, which is why it has been disabled in the both main board and BLE
module Device Tree.
Signed-off-by: Javad Rahimipetroudi <javad.rahimipetroudi@mind.be>
OpenOCD can now be used to flash and debug nucleo_wba52cg.
However it required use of STMicroelectronics OpenOCD fork.
Add instructions on how to use it.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
This reverts commit 6a3612666e
"boards: mps2_an385: Exclude platform from networking tests"
This would have found the issue described in #67762 where a
network test was failing because of wrong section placement.
All the simulated environments (qemu_x86 and native_sim) used
in network testing missed this problem, but could have easily
found if network tests would have been run in mps2_an385.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Instead of relaying on those macros having been defined
somewhere else let's define them for this library.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This constant is supposed to be defined as a long instead of an int,
presumably to support systems where int isn't large enough.
Signed-off-by: Keith Packard <keithp@keithp.com>
Define the pinctrl-based pin controller instance
for the Mercury XU board and remove the old implementation
Signed-off-by: Jan Bylicki <jbylicki@antmicro.com>
Setting an extremely low value by default on two boards doesn't seem
like the right thing to do. The defaults were added with the v1 logging
subsystem in https://github.com/zephyrproject-rtos/zephyr/pull/8023.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Provide three basic examples to test the x-nucleo-iks4a1 shield:
- Test shield in standard mode
Acquire sensor data from shield with all MEMS sensors connected
to micro-controller
- Test shield in HUB1 mode
Acquire sensor data from shield with lis2mdl and lps22df
connected to LSM6DSV16X sensor hub
- Test shield in HUB2 mode
Acquire sensor data from shield with lis2mdl and lps22df
connected to LSm6DSO16IS sensor hub
Signed-off-by: Armando Visconti <armando.visconti@st.com>
x-nucleo-iks4a1 shield is an arduino compatible companion board
which can be used on top of Nucleo standard boards for industrial
applications. Following MEMS sensor are currently supported:
- LSM6DSO16IS: MEMS 3D accelerometer + 3D gyroscope
- LSM6DSV16X: MEMS 3D accelerometer + 3D gyroscope
- LIS2MDL: MEMS 3D magnetometer
- LPS22DF: Low-power and high-precision MEMS pressure sensor
(https://www.st.com/resource/en/data_brief/x-nucleo-iks4a1.pdf)
The board exports three overlays:
1. x_nucleo_iks4a1.overlay (standard mode)
All MEMS sensors are connected to micro-controller.
2. x_nucleo_iks4a1_shub1.overlay (HUB1 mode)
LSM6DSV16X IMU sensor act as a sensor_hub with LIS2MDL and
LPS22DF connected to it.
3. x_nucleo_iks4a1_shub2.overlay (HUB2 mode)
LSM6DSO16IS IMU sensor act as a sensor_hub with LIS2MDL and
LPS22DF connected to it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The nucleo_g0b1re board is based on stm32g0 that supports 2 can
controllers. This commit adds support for the second can controller.
Add also can label in yml board file.
Signed-off-by: Adrien MARTIN <adrienmar@kickmaker.net>
This patch add the basic board support for the
STM32WB5MM-DK Discovery Kit. At the moment only
debug UART Debug is ported. Other peripherals will be added
in the following patches.
Signed-off-by: Javad Rahimipetroudi <javad.rahimipetroudi@mind.be>
In order to build a BLE application nucleo_wba55cg fecthing controller
blobs is required. Document the command.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Let's not treat this driver differently for simulation
than for real HW.
There is a few cases which are not yet working,
but the driver is disabled by default for all platforms.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
CONFIG_RISCV_SOC_INTERRUPT_INIT=y and CONFIG_RISCV_HAS_PLIC=y are both
defaulted to y by the board SoC.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Decrease total RAM usage when Wi-Fi is enabled, specially after
`config HEAP_MEM_POOL_ADD_SIZE_BOARD` was added. This allows application
to handle additional HEAP as required.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
According to the documentation and pinctrl file, sercom0 tx should
be available on PA10C/SERCOM_PAD[2]. However, and somewhat confusingly,
txpo 2 meant SERCOM_PAD[0] with RTS/CTS flow control.
Changing this to txpo 1 uses SERCOM_PAD[2], which allows sercom0
to work as documented.
Signed-off-by: Tom Rothamel <tom@rothamel.us>
Changes:
* Fixed typo in the PWM channel number (32 -> 3)
* Added a prescaler to make the board compatible
with the blinky_pwm sample
Output of the sample before the fix:
PWM-based blinky
Calibrating for channel 32...
[00:00:00.010,000] <err> pwm_stm32: Invalid channel (32)
[00:00:00.016,000] <err> pwm_stm32: Invalid channel (32)
[00:00:00.022,000] <err> pwm_stm32: Invalid channel (32)
[00:00:00.028,000] <err> pwm_stm32: Invalid channel (32)
[00:00:00.034,000] <err> pwm_stm32: Invalid channel (32)
[00:00:00.040,000] <err> pwm_stm32: Invalid channel (32)
Error: PWM device does not support a period at least 31250000
After the fix:
PWM-based blinky
Calibrating for channel 3...
Done calibrating; maximum/minimum periods 1000000000/7812500 nsec
Presence of PWM signal after the fix
has been confirmed using a logic analyzer.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Prevent overrunning the irq vector table.
This is not happening today in tree, but coverity thinks it
may. Checking for it to prevent it is not a bad idea
anyhow, so let's do it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Prevent overrunning the irq vector table.
This is not happening today in tree, but coverity thinks it
does. Checking for it to prevent it is not a bad idea
anyhow, so let's do it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add a new way of passing extra command line arguments
to native simulator based boards using kconfig.
If this new kconfig option is set, its content will be treated
as extra command line arguments/options which will
be parsed before the other command line options.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Switch the default MCUBoot FW Update mode from Swap & Scratch
to more preferable Swap & Move for the rest of NXP MCUs.
Other NXP MCU platforms have been already switched.
Delete the scratch partition. Save RAM & ROM.
Slot 0 has one additional sector, for use with
the swap move algorithm.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Update generation comment for NXP board pin control files, to point
users to the current pin control scripting files in NXP's HAL. Note that
these files have not been regenerated- the script name simply has
changed, so update these references to avoid confusion.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
New UART shim must be adapted to work in the simulated environment.
Use legacy version until it is fixed.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Using the recently added WS2812 PIO driver, this enables the LED on the
QT PY to work with the built in RGB LED examples.
Signed-off-by: Ian Wakely <raveious.irw@gmail.com>
qemu_x86_64 has default of 2 CPUs but the device tree only
has 1. For correctness, add another CPU node to the tree.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update source lib and include path for TF-M interface files.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
The place where TF-M places its non-secure api header files has changed
Therefore changing it for for all applications that use it.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Enable L/R channel pair for DMIC0 on the RT595 EVK. The RT595 EVK has a
pair of MEMS microphones wired to PDM channel 0 and 1, so these channels
are configured with appropriate gain and filter settings for the MEMS
microphones.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Co-authored-by: Yves Vandervennet <yves.vandervennet@nxp.com>
This update stm32h747i_disco board display config to use ltdc frame
buffer config feature.
For lvgl, by default ltdc frame buffer number set to 0.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Add flash partitions required to use the board with MCUboot.
Also fix the chosen zephyr,code-partition devicetree node and point it
to slot0_partition.
Signed-off-by: Martin Jäger <martin@libre.solar>
Add flash partitions required to use the board with MCUboot.
Also fix the chosen zephyr,code-partition devicetree node and point it
to slot0_partition.
Signed-off-by: Martin Jäger <martin@libre.solar>
Add the possibility to flash stm32h747i_disco board using west
STM32CubeProgrammer runner, for both cores.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Tested with zephyr example project "samples/basic/blinky" and "samples/
basic/button". These examples can run out-of-the-box. No modification
needed.
for "samples/basic/blinky", the red LED inside RGB LED on board will
blink every 2 seconds.
for "samples/basic/button", the red LED inside RGB LED on board will
turn on once BTN1 on board is pressed down. An log will be present in
uart console as well.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Add a tag to filter slow bsim tests in CI
(or tests which do not provide much extra coverage and
are not worth running all the time in CI)
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Speed up the interrupt handler when the MCU is woken
due to a phony interrupt (while busy waiting).
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Speed up the interrupt handler when the MCU is woken
due to a phony interrupt (while busy waiting).
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
CONFIG_STM32_LPTIM_CLOCK_LSE definition is now defined directly from
device tree, remove from boards definition.
Solving systematic warning about CONFIG_STM32_LPTIM_CLOCK_LSE being
selected with unsatisfied dependencies.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Since the pins of bt-spi instance are wired internally in the chip, it will
make sense to move the definition to soc dts so no need for every board
using the chip to redefine the same.
Signed-off-by: Aaron Ye <aye@ambiq.com>
Change bin name to esp32_appcpu_firmware instead of
esp32_net_firmware to keep naming coherence.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
SOC_ESP32_NET is now SOC_ESP32_APPCPU, following espressif's
naming convention in the same manner as ESP32S3 app cpu.
SOC_ESP32_APPCU is now a subset of SOC_SERIES_ESP32.
This commit also changes the necessary files, samples and tests
for bisect purposes.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Add support for M5Stack AtomS3 Lite development board.
The AtomS3 Lite is a smaller version of the AtomS3 that
features only a StatusLED and no LCD display.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
Adds the device trees, Kconfig, and documentation files.
The following features have been confirmed working on hardware:
* LED
* Button
* UART
Signed-off-by: Charles Dias <charlesdias.cd@outlook.com>
Power profiles enable the app to dynamically switch modes and support
DVFS. These profiles leverage the PCA9420 PMIC to change the VDDCORE
voltage, and optimize power consumption. Two runtime profiles are
provided for the application:
* main_clk sourced from FRO192M, VDDCORE at 0.9 V
* main_clk sourced from FRO96M, VDDCORE at 0.8 V
Both profiles use the FRO, and the FRO is retrimmed with the target
frequency when switching profiles.
Signed-off-by: Derek Snell <derek.snell@nxp.com>
