Add RT1040 SOC devicetree. This devicetree removes IP blocks absent on
the RT1040, and configures clock dividers correctly for the RT1040's
clock tree
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix PINT base address for LPC51xxx and 54xxx. These addresses were
incorrectly copied from the LPC55S69, which utilizes trustzone. Add the
relevant base address offset to the addresses.
Fixes#57334
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update LTDC driver to use LCDIF bindings, to simplify bindings
between LCD interface controller IP blocks.
Boards supporting the LTDC are also updated to use the properties as
declared by the new lcd controller binding
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Let the Bosch M_CAN front-end drivers supply their own register read/write
functions.
This is preparation for handling non-standard Bosch M_CAN register layouts
directly in the front-end and for accessing Bosch M_CAN IP cores over
peripheral busses.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Currently, the usb_dc_dw driver is not enabled for any platform.
Allow to build the driver for cyclonev_socdk. Subsequent patches
will allow the driver to be used on additional platforms.
Enable USB device controller and use use new snps,dwc2 compatible.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Declare SCB nodes to be used as UART/SPI/I2C by the boards, Move
common declarations from psoc6_02 to the parent dtsi file
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
As recommended in AN4760 the memory region where the QSPI flash can be
memory mapped should be configured to be Strongly ordered memory. This
works around an issue where a speculative read from the CPU may cause
later problems with using the QSPI bus.
This avoids #57466.
Signed-off-by: Ole Morten Haaland <omh@icsys.no>
- Added initial version of Infineon CAT1 Flash driver
- Added binding file for infineon,cat1-flash-controller.yaml
- Added overlays for subsys/nvs and drivers/flash_shell
to support cy8cproto_063_ble, cy8cproto_062_4343w boards
- Defined erase-block-size in PSoC6 MPN dtsi.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Updated the code to to invoke reset using PCR block
z_mchp_xec_pcr_periph_reset() instead of resetting
using I2C Configuration register
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
The SERCOM4 is hardwired to PB30/31, PC18/19 internally for the LoRa
radio. Move the pinctrl entries to SoC dts level. The same applies for
samr35.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In general, peripherals should be disabled by default and enabled at
board level when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add Silicon Labs xG24-PK6010A (BRD4187C radio plug-in board)
support to the efr32_radio board.
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
Add Port 14/15 to device tree. These ports can only be configured as input.
Error out in gpio driver if user sets them as output.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
XMC4500 and XMC47/800 MCUs have a different memory layout. The
definitions have been moved to the derivative .dtsi of each MCU.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
- Remove build asserts in favor of DT enums
- Remove power level property since it is unused by SDK
- Correct voltage ref value in DT to correspond to
chip specific values documented in reference manuals
instead of corresponding to SDK enum names.
- Fix SOC devicetrees affected by these changes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Added a generic driver for RaspberryPi Pico PIO.
This driver is an intermediate driver for abstracting the PIO
device driver from physical pin configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
- To link image loadable by MCUboot, zephyr,code-partition
must be set in the DTS.
- Move partition definitions from SoC DTS to the board DTS.
- Remove scratch partition since MCUboot does not recommend to use it.
- Increase bootloader partitions to 48K to fit recent MCUboot.
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The newly added "power-amplifier-output" property for STM32WL SubGHz
radio nodes is mandatory.
Add the property to all affected modules and boards with the
appropriate value for the factory-default hardware configuration.
Add the "rfo-XX-max-power" properties to all affected modules and
boards with the appropriate value for the hardware configuration.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Adds address cells of size 1 and size cells of size 1 to GPREGRET
instances for Nordic devices.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This commit adds support for the `drivers.adc` test by adding an overlay
for the `efr32bg22_brd4184a` board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
EFR32MG24 uses the Secure Element's mailbox for entropy gathering
purposes. Reflect that in the device tree structure.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
- Add Gecko BURTC sys_clock driver to handle wake up from EM2,3 states
- Remove custom PM policy and dependency on HAL sl_power_manager service
- EM1 supported in all configurations
- EM2,3 supported only if SysTick is replaced by BURTC
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The efr32bg22-pinctrl.dtsi file was shared between bg22 and bg27 files.
It's better to name it efr32bg2x-pinctrl.dtsi.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
This commit splits device tree into more logical structure. Peripherals
which are on a board are in board dts files, while those which are parts of
a SoC are in SoC dtsi files.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
The general structure of efr32b27_sltb010a board is shared by more than one
board. This commit intrduces changes to the organization of board files,
which aim to take that into account.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
