Add definition of the nRF54H20 SoC with its Application, Radio,
and Peripheral Processor (PPR) cores and an initial set of
peripherals.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Make the properties for setting the initial sample points for both the
classic/arbitration phase and the data phase optional.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Implement a sensor for the output diagnostics of the low side
switch BD8LB600FS.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Split up the driver for the low side switch BD8LB600FS into a GPIO
and MFD part.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This binding is for the NXP FlexComm Interface. The
driver will setup an interface for use as a UART, SPI
or I2C device.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
These list of files add basic support for StarFive
JH7110 SOC Device Tree includes for VisionFive2
board.
Signed-off-by: Pratik Farkase <pratik.farkase@wsisweden.com>
Split the common keyboard scanning code out of the XEC specific driver
and use the generic code instead.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the XEC keyboard scanning driver from kscan to input, add the
corresponding kscan compatibility node to the current board, build test
only.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This is a follow-up to commit 4db40601dd.
There are two ECB instances in nRF54H20 and the above commit added
only one of them.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
And add the corresponding bindings.
Move alse the already existing bindings for nrf-dppic, nrf-ppi,
and nrf-ipc so they are located together with the new ones and
in more appropriate folders (DPPIC and PPI peripherals are not
related to ARM, and IPC is for sending and receiving events,
not messages, so ipm/ does not seem to be the best fit for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enabling peripherals at SoC dts files should not be done, unless there
are good reasons (e.g. always needed peripherals). NFCT node should
either be enabled at board level, or, at application level.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Some CAN transceivers have a lower limit on their supported bitrate. Add an
optional "min-bitrate" for specifying this limit via devicetree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The pit had a few warnings about
the format of the register address
being uppser case and one of the
reg index values were incorrect.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Add new devicetree bindings for F4 and L1 series for configuration of
block size used in flash write operations.
Allow byte-size write operations in `flash_stm32f1x.c`. This file is
being shared between F0, F1, F3, L0 and L1 series. L0 and L1 series
allows for single byte writes.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
This commit enables the IRQSTEER interrupt controller
on NXP's XTENSA-based i.MX8QM and i.MX8QXP.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
