This contains accessor macros for getting the maximum bitrate supported
by a CAN controller/transceiver combination.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add generic devicetree bindings for simple CAN transceivers.
Always-on CAN transceivers are considered passive and just provide a
maximum supported bitrate.
Active CAN controllers can typically be controlled by the MCU via either
SPI, I2C, or GPIO. Common GPIO controlled CAN transceivers provide
either a stand-by or an enable pin (or both) for controlling the state
of the CAN transceiver.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for the new pinctrl API to the nRF PWM driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF QDEC driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF QSPI NOR flash driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for configuring pins to be used by the nRF PWM, QDEC, and
QSPI peripherals.
A new custom property "nordic,invert" is added to the pin configuration
group binding to allow configuring PWM channel outputs as inverted.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the DMIC driver that handles
the nRF PDM peripheral. Update code of the driver and the related
devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF I2S driver. Update code
of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Bindings for the Xilinx Processor System GPIO controller, both for the
parent controller device as well as the GPIO pin bank child devices.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Add the parent controller device node plus the child nodes for all
GPIO pin banks managed by the GPIO controller to the device trees
of the Zynq-7000 and ZynqMP SoCs.
Device base addresses, IRQ lines, number of banks, number of pins
per bank and bank descriptions taken from the Zynq-7000 TRM (Xilinx
document ID ug585), the Zynq UltraScale+ TRM (Xilinx document ID
ug1085) and the Zynq UltraScale+ Devices Register Reference (Xilinx
document ID ug1087, web-based document).
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
add dtsi settings for rt series
dtsi use gpr to replace pinmux
nxp iomuxc has gpr which has more settings than mux and io settings
current solution is to export gpr separately and access then directly
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add dts binding for rt1xxx pinctrl driver settings. A binding file is
present for the pinctrl node itself, and for the pinctrl child node that
defines all pinmux options
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce ADC properties which indicated if the ADC instances have
dedicated channels for the internal temperature sensor or voltage
reference.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Don't set AFIOEN when enabling IO port clock.
The bit is set upon requirement within pinctrl
or pinmux
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
RT11xx USB PLLs source from 24MHz XTAL oscillator. Add this oscillator
as a clock source for the usb dts entries for the RT11xx.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This macro expands to DT_STRING_TOKEN if property exists, otherwise
falls back to default value.
Helpful when a non-required enum binding doesn't mention a default
value, but a default value makes sense to be set in the code.
Including DT_INST_STRING_TOKEN_OR and test code.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
rename IMX_CCM_UART_CLK to IMX_CCM_UART4_CLK and
IMX_CCM_UART2_CLK a53 dtsi.
This was missed in a previsous patch set.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support for the new pinctrl API to the I2C drivers that handle
the nRF TWI and TWIM peripherals. Update code of the drivers and
related devicetree bindings.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the SPI drivers that handle
the nRF SPI, SPIM, and SPIS peripherals. Update code of the drivers
and related devicetree bindings.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add power management code for the RT10xx SOC. By default, the code will
simply gate the core clock and transition the SOC to WAIT mode when
sleeping, but if clocking hooks are register to reduce clock frequencies
these will be called as well, and the SOC core voltage will be lowered
for additional power savings.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
1. Check I2C Clock and Data is high through GPIO driver instead
of the I2C bitbang registers
2. i2c_xec_poll_write() and i2c_xec_poll_read() will poll to
check I2C clock and data lines are high before initiating the
transaction. The polling will be every 25us for a cumulative
max of 2.5ms
3. wait_completion() will not call recover_from_error() to reset
the controller. Instead will poll for 10ms for the PIN bit to
clear before returning error.
4. wait_completion() will send STOP if the 9th bit is NACK
5. If any errors with current transaction:
(a) Set error_seen flag.
(b) In the next transaction do the recovery process (reset the
i2c controller) if the clk and data lines are high.
Note: error_seen flag is set for Address NACK with Repeated
Start as well.
6. If timeout error occurs in wait_completion():
(a) Set timeout_seen flag;
(b) Wait till the slave will release the clock.
(c) Once slave releases clock send STOP on the bus. If the
timeout occurred while master read, read the I2C DATA register
for the hardware to proceed.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Since we are moving to pinctrl, removing pinmux.c
from mec172x board folder and removing pinmux from dts
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Allow movement detection to be used on hardware
that only has one interrupt line connected.
Change hardware configuration to a bitmask.
Signed-off-by: Andrew Hedin <andrew.hedin@lairdconnect.com>
The ADC driver of IT81302 chip can support channels 0-7 & 13-16.
This PR adds to implement ADC channels 13-16.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
SOC specific wrapper files were used to include pinctrl DTSI files.
Remove these in favor of including pinctrl header files directly from
board pinctrl definitions.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Kinetis pinctrl groups need dummy pinctrl node to populate with pinctrl
options at the board level. Add one in each
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The dma nodes in device tree were entirely copy pasted. Rather than
doing that lets create a common intel_cavs.dtsi each specialization
then includes. This dedups the lpgpdma entries.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
The Bluetooth HCI driver based on the RPMsg transport now uses the IPC
service module. The compatible Bluetooth sample - HCI RPMsg - has also
been migrated to the new IPC solution.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Add zephyr,memory-region compatible to SRAM1 nodes. These memory
regions are dedicated to the USB device controller for USB descriptors.
Fixes#43090
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
