Remove the requirement for specifying #address-cells and #size-cells
properties for CAN controller devicetree nodes.
CAN controllers do not have a common concept of devicetree child nodes
and thus have no need for these properties. This is in line with
upstream Linux kernel devicetree bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
NPCX series used npcx-lvol-ctrl-map to record the GPIO & low voltage
control register map. However, GPIOE3 was configured as GPIOE6, which
is a non-existed pin. This commit fixes the GPIOE3 low voltage control
map.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Move odr and range properties for both accelerometer and gyro
from Kconfigs to Device Tree.
Fixes#41117
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Fix the yaml dts multi-line property description in the following
(expected) way:
description: |
PUT_TEXT_HERE
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adding support for the TI TMP108 temperature sensor. This includes
over/under temp interrupt support as well as one shot, continuous
conversion and power down modes.
Signed-off-by: Jimmy Johnson <catch22@fastmail.net>
By enabling SMP option plus the APPCPU, also
completes the SMP port by adding the esp32
specific arch_sched_ipi() function
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
RT11xx can peripheral had incorrect clocking configuration in SOC clock
init code and DTS. Fix peripheral configuration.
Fixes#41251
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a display driver and the corresponding devicetree binding for a LED
matrix with rows and columns driven by nRF SoCs GPIOs. Such matrix can
be found, for example, in the BBC micro:bit boards.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add board support for NXP i.MX8M Plus EVK. This board has the following
features:
Processor : i.MX8M Plus Quad applications processor
Memory : 32-bit LPDDR4 w/6 GB
eMMC 5.0/5.1 w/32 GB
SD/MMC connector
QSPI w/32 MB
Connectivity : MIMO 2x2 Wi-Fi 802.11b/g/n/ac and BT 4.2
2x Ethernet (1x w/ TSN)
PCIe M.2
2x CAN FD DB9 Female connectors
USB : USB 3.0 Type C for Power
USB 3.0 Type A
USB 3.0 Type C
Debug : JTAG connector
MicroUSB for debug console
More information about this board can be found in NXP website: https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-plus-applications-processor:8MPLUSLPD4-EVK
Signed-off-by: Chris Trowbridge <chris.trowbridge@lairdconnect.com>
When building for an STM32K010xB MCU, there is a deprecated properties
warning, which should be fixed by this PR.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
Everything I can find as a reference says that the LP-SRAM block on
these devices is 64kb, and direct experimentation with cAVS 1.5 and
2.5 agrees. Access to areas beyond 64k hangs the DSP (it should cause
a PIF fault I guess, but the exception never gets trapped, that's
probably a different problem).
Fix this in devicetree to reflect what actually works. It's not clear
where the 128k values came from; if they're not typos we can correct
that when we find better docs.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Create an explicit ina230 driver which is supposed to
work with 230 and 231 variants. While at it switch
to i2c_dt_spec helpers and change device-tree node
names to use - instead of _ in order to follow
convention.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by lps22hh driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
PSL_IN pin select register is Vsby power-up reset. When the other
core-domain-reset reset the chip, PSL_IN3/4 don't set to GPIO. This
commit adds PSL_IN3/4 to the pin select list in NPCX devicetree. So
these pins can be set to GPIO when the other core-domain-reset.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
GPT base address in the devicetree for the RT11xx SOC series was
incorrect, this commit fixes it
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added a driver to enable the GPT timer on RT1xxx parts to be used
instead of systick as a clock source. The timer is set to run in reset
mode, and uses the low frequency 32kHz oscillator for power savings
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for the 8 channels TCA9548A I2C mux.
Added a new binding ti,tca9548a binding inheriting
properties from ti,tca954x-base and defining its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Add an optional "reset-gpios" phandle-array
field to the driver common yaml.
The reset GPIO channel and pin can be defined
in device tree as a node property.
The driver then deassert the reset signal at mux
initialization if a "reset-gpios" has been specified.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Prepare the driver to upcoming support of more mux references.
Rename all TCA9546A related files to TCA954x.
Keep ti,tca9546a and ti,tca9546a-channel compatible
for backward compatibility reasons.
New tca954x-base binding embedding common properties,
tca9546a binding inherits from it and define its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Include the mem-region bindings for the stm32 ccm nodes and set the name
in the current dtsi files.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add the compatible property to the board level sdram nodes in few stm32
dts files so that the zephyr,memory-region name is used correctly in the
linker script.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add bindings for SDL based display controller.
Rework SDL based display controller driver to obtain
configuration from devicetree. Remove unnecessary casts,
add multi-instance support.
Add display controller node and chosen property
to native_posix devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Include common display controller bindings.
Add required height and width properties to "ilitek,ili9340"
and "ilitek,ili9488" users.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Not all boards use the same UART's defaults properties.
This commit updates device tree declarations by deferring
specific definitions to the board's DTS.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Not all boards use the same UART's defaults properties.
This commit updates device tree declarations by deferring
specific definitions to the board's DTS.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Enable flexspi for RT11xx SOCs. This requires selecting the correct
KConfig symbol for the cortex m4 and m7 SOCs, as well as correcting an
error in the flexspi DTS node and updating the clock init for RT11xx
SOCs.
Note that in addition, the NXP hal must be updated to properly support
including the cache management driver for the Cortex M4.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce optional `zephyr,linker-region` property which signifies that
the node should result in a linker memory region and what the name of
that region should be. Property added to compatibles likely to result
in a linker memory region; 'mmio-sram', 'arm,itcm`, `arm,dtcm`,
`nxp,imx-itcm`, `nxp,imx-dtcm` and `fixed-partitions`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Refactor the mcp230xx driver to generically also support
SPI IO expanders, renaming it to mcp23xxx in the process.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add driver for MEC172x QMSPI with local DMA(LDMA). The driver
support SPI asynchronous operation.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
DMA controller is enabled and tested for cortex M7 core. The M7 core was
tested on the loop and channel link transfer tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
DMA controller is enabled and tested for cortex M7 core. The M7 core was
tested on the loop and channel link transfer tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds a generic i2c regulator driver, and enables the NXP
PCA9420 PMIC IC using this driver. The regulator driver also exposes an
additional API in include/drivers/regulator/consumer.h, which allows
drivers to implement support for adjusting voltage levels and current
limits, if their device supports it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
the RT685 contains an additional flexcomm peripheral, that supports
only I2C. This commit adds this peripheral to the device tree,
and enables pins and clocks for flexcomm15.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
There is currently no information available about the XIP
addresses for the nRF52840 and nRF5340.
Add this via a new 'reg' block in the relevant QSPI nodes, along with
names for the register blocks so they are easier to retrieve.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This board, whose hardware is just a cAVS 1.8 device without an x86
host CPU, started life (as all the cAVS devices did) as a
cut-and-pasted copy of the same basic code.
Because of hardware and schedule limitations, it didn't get the same
unification treatment that all the other platforms did. But it turns
out that in SMP configurations (which... it's not clear if we actually
test on hardware?) it wants to use the cavs_timer driver, which now
uses the new SOC API and not the old one. Which s1000 doesn't expose.
So... I guess we have to continue to cut and paste until we can find
time to unify this. Add a copy of the new shim/IDC headers to this
SOC and expose them via devivcetree.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Adds a driver using the SNVS high power and optionally low power
RTC instances. A device specific function `mcux_snvs_rtc_set` is
provided to update the current counter value.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
GPIO10 was missing from RT11xx DTS, and is required to manage SD card
power. Enable this GPIO.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The commit adds "disk-access" property to fstab bindings to allow
selecting FS_MOUNT_FLAG_USE_DISK_ACCESS while defining file
systems in DTS.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This adds an spi master mode driver via bitbanged gpio. Only syncronous
transfers are implemented. Clock signal timing is accomplished via busy
waits, the gpios are manipulated via the standard gpio interface; these
two factors limit the frequency at which it can operate - but here
a simple and generic implementation was chosen over performance.
The driver supports the various clock polarity and phase
configurations, and can also work with word sizes which are non
multiples of 8bits, currently up to 16 bits.
A sample program is also added demonstrating basic use of the driver
with 9bit data words.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
MCUX PWM driver used hardcoded clock source. update driver to use clock
bindings to determine PWM peripheral clock frequency.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Adds optional device tree properties to insert delays between spi chip
select assert/deassert and the clock edges, and also between spi
frames and transfers to the mcux flexcomm spi driver. If the properties
are not set, no additional delay is inserted.
Verified expected behavior on mimxrt685_evk and check with a scope
that the pre- and post-delay could be changed from the device tree
properties.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
This commit adds support for IMX6SX PWM.
The PWM module is the same module present on the IMX7D and so dts
bindings has been renamed following the one present on linux.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Most of the time SPI devices use TI's frame format. But some may use
Motorola's. This is already taken care of in the SPI API and now it will
be possible to select the right format from DTS. Like:
...
frame-format = <SPI_FRAME_FORMAT_MOTOROLA>;
...
This is only meant to be used for devices supporting both formats (so
the format is not hard-coded in the driver) and selected by hardware
configuration or else. Which, in such case, it will need to use
DT_INST_PROP(<instance number>, frame-format) macro call to retrieve
the property value. Others can fully ignore it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Software reset is already implemented in the driver when the
`reset_gpio` is not defined. However it could not be activated
because the `reset_gpio` is a required field in the DTS
binding.
Signed-off-by: Casper Meijn <casper@meijn.net>
This patch adds support for the new pinctrl API to the UARTE driver. The
old pin property based solution is still kept so that users have time to
transition to the new model.
Notes:
- Some build assertions cannot be performed since the driver does not
have direct access to pin settings anymore. As a result user will not
be notified if HWFC is enabled but RTS/CTS pins are not configured.
- Hardware flow control can be enabled regardless of pin configuration,
it is now up to the user to configure RTS/CTS pins in DT.
- Some RX enable checks that were performed using pin information has
been replaced with a DT property that informs if RX is enabled or not.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add initial support for nRF pin controller driver. The implementation in
this patch does not yet support any peripheral. Only states
representation and basic driver functionality is introduced.
Note:
The nrf_pin_configure function has been marked as __unused since it may
not be used in certain scenarios until all peripherals are supported by
the pinctrl driver. For example, if only UART/E is supported but the
board does not enable UART, the function will never get called. However,
that board will likely have other peripherals that will gain support in
the future.
Thanks to Marti Bolivar for bindings documentation.
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Now that STM32 drivers are using pinctrl API, set pintrl-0 and
pintrl-names properties as required in order to report malformed
nodes description soon at build stage and avoid cryptic
DT api build error messages.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new pinctrl API to configure pins.
Since STM32F1 series require pinctrl option and required register
address is parent timer address in place of own node register address,
use PINCTRL_DT_INST_CUSTOM_REG_DEFINE in place of usual
PINCTRL_DT_INST_DEFINE for this specific series.
Additionally, remove the automatic selection of PINMUX API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new pinctrl API to configure pins.
Additionally, rename usb_pinctrl to usb_pcfg to better fit
new pinctrl API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the CAN peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the I2C peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use nrfx_gpiote and nrfx_ppi allocators to allocate channels
at runtime instead of fixed, device-tree based allocation which
is harder to maintain.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add bindings for a generic PCIe Controller in ECAM mode.
ECAM stands for PCI Express Enhanced Configuration Access Mechanism
where the PCIe config space is flat memory-mapped.
An optional msi-parent phandle is added to link to an optional
MSI/MSI-X Interrupt Message Translation HW component.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The qemu arm64 virt machine PCIe controller config space needs a
64bit adressing, so switch the entire qemu-virt-a53 and
qemu_cortex_a53 board dts to address-cells & size-cells to 2
to accommodate for 64bit addresses.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
These registers were hardwired in the platform layer. Move to
devicetree, via a struct interface that looks like the pre-existing
shim layer.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These registers are identical on all platforms, the only difference
being that cAVS 1.5 places them at a different address.
Create a devicetree node to track the register block, and replace the
platform header code with a global API defined once (it works like the
pre-existing shim struct).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Each platform was defining its own shim.h header, with slightly
variant field definitions, for a register block that is almost
completely compatible between versions. This is made worse by the
fact that these represent an API imported fairly early from SOF, the
upstream version of which has since diverged.
Move the existing shim struct into a header ("cavs-shim.h") of its
own, remove a bunch of unused symbols, fill in definitions for some
registers that were left out, correct naming to match the hardware
docs in a few places, make sure all hardware dependencies are source
from devicetree only, and modify existing usage to use the new API
exclusively.
Interestingly this leaves the older shim.h header in place, as it
turns out to contain definitions for a bunch of things that were never
part of the shim register block. Those will be unified in separate
patches.
Finally: note that the existing IPM_CAVS_IDC driver (soon to be
removed from all the intel_adsp soc's) is still using the old API, so
redeclare the minimal subset that it needs for the benefit of the
platforms in transition.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This is dead code. It's based on the cAVS "IPC" mechanism to allow
communication to and from the host CPU. But there is no test rig in
the Zephyr tree for the protocol defined. And in fact the only
Zephyr-based user of the IPC mechanism (Sound Open Firmware) has its
own IPC driver and speaks its own protocol with the host kernel. That
driver needs to migrate into Zephyr soon and this legacy bit is just
confusing.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Introduce a new RPMsg with static VRINGs backend. This new backend makes
easy to generate and use IPC instances backed by OpenAMP using the DT.
Each instance is defined in the DT as (for example):
ipc: ipc {
compatible = "zephyr,ipc-openamp-static-vrings";
shm = <&sram_ipc0>;
mboxes = <&mbox 0>, <&mbox 1>;
mbox-names = "tx", "rx";
role = "primary";
status = "okay";
};
It is then possible to register an send data through endpoints using the
IPC service APIs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
* With existence of Adafruit Qt Py boards, and upcoming wireless
Xiao from Seeeduino, define nexus node and peripheral node
labels for use with shields that accept any Xiao format board.
* Adds `&xiao_d`, `&xiao_spi`, `&xiao_i2c` and `&xiao_serial` generic
node labels.
* Add new 'seeed-xioa-header.yaml` to document new nexus node.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add a pin control driver for GD32 SoCs using the AFIO model.
Thanks to Gerson Fernando Budke for testing and implementation
suggestions.
Co-authored-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
1.Putting the PWM_CHANNEL_X, PWM_PRESCALER_CX information
in the description.
2.Use the common definition EC_FREQ.
3.Use the common macro IT8XXX2_DT_ALT_ITEMS_LIST.
4.Stop using DRV_CONFIG, DRV_REG macro.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Users will have to include dt-bindings/spi/spi.h in order to use the
relevant flags fol this property. For instance:
...
duplex = <SPI_HALF_DUPLEX>;
....
By default all SPI device are configured to be full duplex so the
property is optional. This property makes sense only for devices that
can be configured on either modes. Which, in such case, it will need to
use DT_INST_PROP(<instance number>, duplex) macro call to retrieve the
property value. Others can fully ignore it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add tests for the instance based enum macros DT_INST_ENUM_IDX and
DT_INST_ENUM_IDX_OR.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The Flexspi memory address defines the location of the externally
attached flash to the MXRT600 based board. The flexspi has two
different memory spaces for secure and non-secure access that are
not aligned for the Flexspi register space and the memory map
address space. The normal method of handling this via the two
different dts files for secure/non-secure is not able to handle
this because a base address is applied uniformly across multiple
reg items.
Changes include:
- pull flexspi out of peripherals block to allow it to be explicitly
expressed in the respective secure/non-secure SOC DTS files.
- move the flash size definition to the board level definition and
use the size of the actual flash device found on the board.
:
Signed-off-by: David Leach <david.leach@nxp.com>
IT8XXX2 uses shared ns16550.c driver which does not provide a power
management callback(pm_action_cb), so create driver to handle
IT8XXX2 specific UART features.
note: pm_action_cb(old name: pm_control_fn)
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Prescaler was misplaced in pwm binding, instead of timers binding.
For example, TIM6/TIM7 doesn't have PWM capability,
but have a prescaler.
This change also prepares the introduction of timer based counter
(which requires prescaler at timer level)
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Prescaler was misplaced in pwm binding, instead of timers binding.
For example, TIM6/TIM7 doesn't have PWM capability,
but have a prescaler.
Also prescaler is common to all PWM channels of the same timer.
This change also prepares the introduction of timer based counter
(which requires prescaler at timer level)
For compatibility reason temporarily keep pwm binding to avoid
breaking boards out of tree.
Block st,prescaler property in lptim binding
as lptim doesn't use this property for now.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This will be used to take a phandle to a FEM device, either a generic
two pin device or an nRF21540. Keep the nRF21540 binding example up to
date.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The way the nRF21540 device is configured makes sense once you
understand it, but it's quite unusual: a single peripheral is
configured with two separate devicetree nodes linked by a phandle.
Since this risks entering "exploding head" territory for beginners, it
deserves a thorough example. Add one to the binding's description.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is a helper binding for radio front-end modules that have a
two-pin control interface, where one pin is used to turn on an power
amplifier (PA) for TX, and another is used to turn on a low-noise
amplifier (LNA) for RX.
Such hardware is already supported by the Bluetooth subsystem, but via
PA/LNA Kconfig settings. Since this is hardware configuration, it is
better to move this to devicetree instead.
Add a binding that makes it possible to define nodes which contain the
same information, along with a bit of extra information related to the
gain in dB of each amplifier not currently available from Kconfig.
This is similar to the existing binding for the nordic,nrf21540-fem
compatible.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Andrzej Kuros <andrzej.kuros@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is to support upcoming external radio coexistence implementations,
see binding documentation for more info.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
add ledc to board dtsi file,
change compatible and device define in pwm driver,
add yaml for board ledc support,
fix missing include for board in gpio include
Signed-off-by: Andrei-Edward Popa <andrei_edward.popa@upb.ro>
Use i2c_hal functions to enable support for
multiple SoCs.
Use DT compat to enable I2C from device
tree configuration
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This joins all clock control handling to same source
by using hal clock functions. It also brings ESP32C3
clock support.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Add the USB On-The-Go Supplement, Revision 2.0 in the DTS
of the stm32u575 and stm32u585 devices
(not for the stm32U5 serie).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In order to have Espressif SoCs working with
the same uart drivers, all low level functions
are now replaced to hal_espressif HAL calls.
This also changes pinmux, gpio and uart
init order to meet its dependencies.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
STM32WL could be either single core (stm32wlex) or
dual core (stm32wl5/4x).
Make CPU2 prescaler an optional property (while it will
be required if inherited from st,stm32wb-rcc.yaml.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that Kconfig option for STM32 clocks configuration has been
removed, set rcc properties as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fix register addresses in rt11xx SOC dts. Flexcan1 was defined with an
incorrect register address, and watchdog 3 was incorrectly labelled as
watchdog 1. Watchdog 2 should not be enabled, as it is only accessible
from code running in the trustzone context.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add baseline support for mimxrt1160_evk Cortex M4 and M7 cores
UART shell, synchronization, and hello world have all been verified to
build and run correctly.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert all in-tree NXP FlexCAN instances from hardcoding the CAN bus
timing in time quanta to specifying a desired sample point of 87.5% as
recommended by CAN in Automation (CiA).
This allows for the CAN driver to calculate the optimal time quanta
based on the CAN clock and the requested CAN bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Added watchdog implementation which is using counter device
to implement watchdog driver API. Watchdog timeout is called from
counter interrupt context. Some counter implementations support
using ZLI interrupt level which can be use here as well. Watchdog
like this can be used along hardware watchdog to cover for its
limitations, i.e. Nordic watchdog resets unconditionally after
62uS after triggering watchdog interrupt. It is not enough time
to dump logging data.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The FIU/UMA module in the NPCX chip provides an dedicated SPI interface
to access the SPI flash. This commit adds the driver support for it.
With this commit, the application can call the flash APIs
(via spi_nor.c) to access the internal flash of NPCX EC chips.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I32bbf09f6e014b728ff8e4692e48151ae759e188
Add the power state of deep doze. When system enters deep doze, the
clock of CPU and EC can be stopped to reduce power consumption. And
enable the UART Rx WUI before entering deep doze to wake up EC and
CPU.
Tested on it8xxx2_evb board. It will reduce 5.25mA when system enters
deep doze mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add SoC-specific code, the basic device tree and Kconfig data as well
as the corresponding linker command file for the Xilinx Zynq-7000
family of SoCs. This SoC - either as a QEMU simulation or on actual
hardware such as the Avnet/Digilent ZedBoard - is suitable as an ini-
tial target for the ARMv7 Cortex-A support.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Rewrite the NRFX IPC driver to properly support multi-channel addressing
leveraging the newly introduced MBOX APIs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
One limitation of the current IPM API is that it is assuming that the
hardware is only exporting one single channel through which the data can
be sent or signalling can happen.
If the hardware supports multiple channels, the IPM device must be
instantiated (possibly in the DT) several times, one for each channel to
be able to send data through multiple channels using the same hw
peripheral. Also in the current IPM API only one callback can be
registered, that means that only one driver is controlling all the
signalling happening on all the channels.
This patch is introducing a new MBOX API that is supporting
multi-channel signalling and data exachange leveraging and extending the
previous (and outdated) IPM API.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This is a driver for the Synopsys DesignWare MAC. It should work
with the "DesignWare Cores Ethernet Quality-of-Service" versions 4.x
and 5.x.
This driver uses a zero-copy strategy, meaning that the hardware
reads and writes data directly from/to packet fragment buffers
provided by the network subsystem without first copying the data into
a dedicated DMA bounce buffer.
Platform specific setup is necessary for the hardware to work.
Currently, only the STM32H7X series is implemented and tested.
While this part needs refinement, this driver performs better and uses
far less code space than the HAL-based alternative.
Not yet implemented:
- MDIO (it is WIP, currently relying on default PHY config)
- PTP support
- VLAN support
- various hardware offloads (when available)
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
MEC172x eSPI driver, eSPI pin programming, interrupt updates related
to eSPI and other updates for MEC172x eSPI driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Pick those common node in 'fvp-baser-aemv8r.dts' to 'fvp-aemv8r.dtsi'
which reside in 'dts/arm64/fvp-aemv8r' directory.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
Add a set of tests to check the API behavior. The API tests can only run
on a platform that does not have an actual pinctrl driver, e.g.
native_posix. The test itself implements a pinctrl mock driver and
provides the required "pinctrl_soc.h" header with required types/macros.
The implementation is used in the tests to verify the behavior of the
API or Devicetree macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
When using group based representation on pinctrl nodes, the pin
configuration properties end up being at the grand-children level, so
the `pincfg-node.yaml` file can't be used.
Having a common file that can be used for both cases would require
tooling changes, so for now a copy that operated at the grand-children
level has been created.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Initial skeleton for pinctrl drivers. This patch includes common
infrastructure and API definitions for pinctrl drivers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move odr options from Kconfigs to Device Tree. Moreover add
in DT a power-mode option to select among 4 possible values
(PD, LP, HR, HF). The power mode cannot be currently set from
sensor APIs.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all DT
bindings (as i2c and spi) handled by lis2ds12 driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add a dedicated compatible for STM32MP1 clock control node.
Since, on such platform, clock configuration is done on A9
side, only the clock-frequency property is available.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add dtsi file for i.MX8MP board.
This has one HiFi4 core, from Cadence, lx6 compatible
and 2 System RAM.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Add a DTS description of timer5 to: STM32G474, STM32G484, STM32G473,
STM32G483, and STM32G471
Add a DTS description of timer5 to: STM32G474, STM32G484, STM32G473,
STM32G483, STM32G491, and STM32G4A1
Signed-off-by: Pete Dietl <petedietl@gmail.com>
Add general mboxes, mbox-names to base.yaml to be utilized by any
clients that use mailboxes.
Additionally add mailbox-controller.yaml for common properties shared
by all mailbox controller devices.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add devicetree nodes for the NEORV32 GPIO device.
The GPIO port is 64 bits wide, but Zephyr only supports up to 32 bit
wide GPIO ports. The GPIO device is therefore handled as two Zephyr GPIO
devices with a nexus devicetree node mapping pins 0 to 31 to the device
handling the lower half, and pins 32 to 63 to the device handling the
upper half.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Currently all the *-names and *-cells properties are derived from the
name of the base <name>s property. This is a limitation because:
- It forces the base property name to be plural ending in -s
- It doesn't allow the english exception of plural words ending in -es
With this patch we add one additional property 'specifier-space' that
can be used to explicitly specify the base property name.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Suggested-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
1) Allow use of interrup driven instance.
ROM implementation could be selected via dts compatiable.
2) Use UART rx fifo and timeout interrupt for end of message detection.
Added to decrease interrupts count on data reception
3) Use ESP_LL api.
Signed-off-by: Pavlo Hamov <p.hamov@venstar.com>
Adds SPI support on LPSPI1 to the RT1010. LPSPI1 is available on pins
6, 8, 10, and 12 of J57 on the evaluation board
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit enables the LPSPI1 peripheral on the RT1015 EVK. LPSPI pins
are not populated by default, but headers can be added to J19 on the EVK
to access these signals
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add device tree for Intel SoC FPGA Agilex initial bring up. This is the
first version of device tree which enable single CPU core and basic
drivers that needed by hello_world example.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
The shared multi-heap memory pool manager uses the multi-heap allocator
to manage a set of reserved memory regions with different capabilities /
attributes (cacheable, non-cacheable, etc...) defined in the DT.
The user can request allocation from the shared pool specifying the
capability / attribute of interest for the memory (cacheable /
non-cacheable memory, etc...)
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add specific properties to enable remap for PA11/PA12, which is a
possibility on STM32G0/F0 SoCs.
These properties only have effect when defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This name should be the same as cpus node in dtsi. After the power
policy is added, the cpu-power-states in the CPU properties can
be used.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
AHB prescaler is a value which divides the SYSCLOCK
to provide the HCLK. The HCLK supplies the core, AHB bus, memory.
On the stm32wb and stm32wl, the HCLK for CPU1 is HCLK1
with cpu1-prescaler.
By default the value is 1, else the HCLK must be correctly set.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
interrupt controller, also places its relevant
peripheral sources allowing drivers to use the
DT macros instead of espressif headers.
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
This reverts commit d3a558591f.
We shouldn't be adding vendor prefixes for things we don't have
upstream bindings for unless we've inherited them from Linux.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
If supported by the SPI instance and soc, this property will
configure the frame-format to be compliant with the TI mode.
By default, if supported, the frame-format is Motorola mode.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The maximum supported speed according to the SX126x datasheet (I have
not found that information in the STM32WL datasheet or reference
manual). Increase the Sub-GHz SPI frequency from 1 Mhz to to 12 MHz,
which corresponds to a baud rate prescaler of 4 with a 48 MHz clock. It
also matches what is done the the STM32CubeWL package.
This reduces the time the MCU is kept running, thus reducing the global
power consumption.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This adds the uart4 device to the stm32f3_disco board
based on the stm32f303 device from STMicroelectronics
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds stm32f103xd series dts file that was missing.
Also, changed stm32f103xe.dts for highlighting the differences between
f103xd and f103xe series.
Signed-off-by: Deimantas Aukštkalnis <deimantas.aukstkalnis@teltonika.lt>
Add DT bindings for the optional Interrupt Translation Service module
of the ARM GICv3 Interrupt Controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Implements a shim layer driver using st hal for
I3G4250D gyro, mounted for example on stm32f3_disco_E.
No support for triggers included yet.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
1. Add support for multiple syscon entries (as a side effect, this also
fixed syscon.c implementations which weren't being linked to their
syscon.h counterparts).
2. Add support for different width registers in syscon.
3. Add tests for syscon
Signed-off-by: Yuval Peress <peress@chromium.org>
Since version 1.11.0, Full stack M0 binary requires 216K of flash
being available, while previously 212K were required.
Review flash partitioning to take it into account.
Additionally:
- update value in board yaml file.
- align value in package .dtsi file
Fixes#38735
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The NPCX I2C implementation contains two modules, an I2C port and an
I2C controller. Disable the I2C controller nodes by default and require
the user to enable both the I2C port and controller in the devicetree.
Signed-off-by: Keith Short <keithshort@google.com>
Fix a typo bug where sercom5 pinctrl has pad2 and pad3
has duplicated pads for pb0/pb2 and pb1/pb3.
Per the datasheet, pb2 and pb3 should be pad0 and pad1 respectively.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
TWIM peripherals cannot perform write transactions from buffers
located in flash. The content of such buffers needs to be copied
to RAM before the actual transfer can be requested.
This commits adds a new property (zephyr,flash-buf-max-size) that
informs the driver how much space in RAM needs to be reserved for
such copying and adds proper handling of buffers located in flash.
This fixes an issue that caused that e.g. the DPS310 sensor driver
did not work on nRF SoCs that only have TWIM, not TWI peripherals.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Issue an error logging message when the i2c_nrfx_twim driver lacks
a concatenation buffer big enough to properly handle a call to
i2c_burst_write() function, to give the user a hint what is wrong.
Also use by default a 16-bytes long concatenation buffer for every
instance of the i2c_nrfx_twim driver. Such value should cover most
of the simple uses of the i2c_burst_write() function, like those
in the stmemsc sensor drivers, and when a longer buffer is needed,
the user will be provided with the above message pointing to the
property that should be adjusted.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove the HL7800 DTR device tree binding because the
DTR IO is not needed for operation of the HL7800
modem.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
This patch fixes wrong PLIC irq number of UART and SPI for SiFive
FU740 on HiFive Unmatched. Use samples/subsys/console/echo for
testing.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
The priority of the LPTim interrupt on each stm32 soc
is put at the same level as the SysTick. This priority
level is given by the system Handler priority reg
(SHPR3) when the PM is not configured.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
stm32f411 includes stm32f401 which do already correctly define spi4
The definition in stm32f411 was missing a clock attribute
Signed-off-by: Kim Bøndergaard <kim.boendergaard@escoglobal.com>
stm32f410, stm32f411 and stm32f412 enable the SPI5 device with
bit 20 on the APB2 clock
Signed-off-by: Kim Bøndergaard <kim.boendergaard@escoglobal.com>
This patch adds support for SiFive Freedom U740 SoC.
First version is minimum only using UART, SPI and L2-LIM area.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
This patch adds support for SiFive Freedom U540 SoC.
First version is minimum only using UART, SPI and DDR memory area.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
