Adds an fxos8700 device tree node to the mimxrt1050_evk. The sensor
interrupt gpios require a board modification to be used and conflict
with Ethernet and LCD signals, therefore their pinmuxes are not
configured.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1050_evk
board. Updates the board documentation and yaml supported list
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The schematic shows that both INT1 & INT2 from the MMA8652FC are wired
up, update the dts to reflect this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configuration of Erase command is specified in DTS. Hence
the corresponding changes in Kconfig are removed.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Number of sectors is now calculated from the flash density
i.e. (Flash size)/(sector size).
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The starting 192kB SRAM is reserved for the mcubootloader. Exclude
this region while building an application to be loaded by mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
FIFO_DEPTH should be in the SoC's Kconfig as this is a
configuration of SPI master controller in SoC.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patchset introduces partitioning of flash in terms of blocks
(flash page layout) for s1000. This partitioning is currently to
be used for mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Use DT_ instead of CONFIG_ for spi freq, spi bus name, flash device
name and flash base address.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Update boards yaml file with arduino_i2c supported option
We exclude disco_l475_iot1 from the x_nucleo_iks01a1 sample since there
are duplicated sensors between the disco_l475_iot1 and shield. Until
Zephyr drivers can handle multiple sensors we need to have this exclude.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables instance 3 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1060_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables instance 2 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1020_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This board has headers for these buses so they should be made available
without requiring special overlays.
Also take advantage of the new Nordic auto-enable for peripherals,
which eliminates the need for special configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Not all boards can get the coverage reports. The report generation
needs minimum of 64KB SRAM. This patch added support for mps2_an385,
qemu_cortex_m3, qemu_x86. This is just a subset. Also the previously
supported board native_posix is included in this patch.
If a board has 64KB RAM, it can generate reports by just
adding HAS_COVERAGE_SUPPORT in Kconfig.board.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Support musca board as a variant, it is a Cortex-M33 based SoC.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Signed-off-by: Minos Galanakis <minos.galanakis@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update nucleo_l073rz to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
- update yaml
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_l053r8 to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f446re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- disable I2C by default
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f411re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f401re to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- disable I2C and PWM by default
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f302r8 to fit with default configuration guidelines:
- remove reference to arduino_serial as Ardiuno D1/D0 are actually
mapped on PA2/PA3 which are already used for ST_Link com port,
hence not available by default for arduino serial
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f070rb to fit with default configuration guidelines:
-configure arduino spi and i2c
-update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The test suite will use the m2gl025_miv.resc Renode script to load the
platform.
Signed-off-by: Dawid Wojciechowski <dwojciechowski@internships.antmicro.com>
Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
For normal (over-the-wire) mode of CAN sample lowering bitrate to
125000 to ensure reliable transfer on stm32f072b_disco boards
Signed-off-by: Andrei Laperie <andrei.laperie@intel.com>
Increase the size of the MCUBoot flash partition in the fstab-debugger
partition table, to accommodate for the RTT console and logs.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The MCUBoot partition in the default partition table (fstab-stock)
is not meant to accommodate an RTT console, since the board does
not have a SEGGER chip.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
