Corrects the size of the external octoFlash connected to the
mcu of the stm32h573i disco kit from STMicroelectonics
Signed-off-by: Francois Ramu <francois.ramu@st.com>
After adding new GPIOTE instances, there is a need
to enable the instance for individual boards.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Change the GPIOTE driver to HAL to prevent instantiation
issues with a multi-instance GPIOTE driver.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
- board.cmake is augmented for LinkServer (now the default runner
for this board)
- the board's doc file is updated as well
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
- board.cmake is augmented for LinkServer (now the default runner
for this board)
- the board's doc file is updated as well
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
this corresponds to soc/arm/nxp_lpc/lpc55xxx/soc.c:129. also, 16MHz is
used on the lpc55s69-evk.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
enable CONFIG_USB_DC_HAS_HS_SUPPORT when we use only OTG_HS
and not OTG_FS.
in that case TEST_BULK_EP_MPS (Endpoint max packet size)
equal 512 and not 64
it is the case for nucleo_h723zg and for nucleo_h7a3zi_q
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
Enable FlexTimer (FTM) as a PWM controller for this board. Use the RGB
LED controlled by FTM0 as PWM-LEDs for the samples and tests.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Set CONFIG_MCUBOOT_BOOTLOADER_MODE_OVERWRITE_ONLY=y
for lpcxpresso55sxx boards.
Synchronize with their default MCUBoot configuration.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
The W5500_EVB_PICO is an evaluation board for the Wiznet W5500
ethernet mac/phy based on the Raspberry Pi Pico.
Signed-off-by: Ian Wakely <raveious.irw@gmail.com>
Only reset cause is supported as there is no common unique id
present on those chips.
Unique ID can be put in OTP but there is no single specification for this.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This adds the pins for the board's USB Micro-B connector to the device
tree as zephyr_udc0, allowing USB examples to run natively on the board
Signed-off-by: James Anderson <jrsa@jrsa.co>
Adding support for the Adafruit QT PY RP2040.
Signed-off-by: Kelly Helmut Lord <helmut@helmutlord.com>
Signed-off-by: Ian Wakely <raveious.irw@gmail.com>
This commit updates the Ambiq Apollo4x series soc clock frequency
of defined instances to align with context of these dts files.
Signed-off-by: Aaron Ye <aye@ambiq.com>
This commit updates the support features in document and yaml files
of Ambiq apollo4p_evb and apollo4p_blue_kxr_evb.
Signed-off-by: Aaron Ye <aye@ambiq.com>
Added counter in supported hardware features.
It forgot in the commit when introducing the counter driver.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Added counter in supported hardware features.
It forgot in the commit when introducing the counter driver.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Added counter in supported hardware features.
It forgot in the commit when introducing the counter driver.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Kconfig options with a HEAP_MEM_POOL_ADD_SIZE_ prefix should be used to
set the minimum required system heap size. This helps prevent
applications from creating a non-working image by trying to set a too
small value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This PR corrects the RAM size specification of
the Infineon CY8CPROTO-062-4343W PSoC6 eval board.
Fixes#60876
Signed-off-by: Manuel Loew <manuel.loew.infineon@gmail.com>
To be compatible with BLE operation and BLE Controler configuration,
update board clock configuration to work using a fixed core clock at
16MHz.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
The BT HCI uses internal IOM4 (SPI4) for communication bus.
Set the default configuration for BT based on the controller supported
capability and HCI driver dependency.
Signed-off-by: Aaron Ye <aye@ambiq.com>
Add the possibility to flash stm32f429i_disc1 board using
STM32CubeProgrammer & patch the OpenOCD cfg.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Generic Connector for the apollo4p_evb
Ran tests/drivers/gpio/gpio_basic_api
Ambiq does not support DUAL Edged Interrupts.
Added Connector Usages as defined by the Ambiq BSP.
Signed-off-by: Richard Wheatley <richard.wheatley@ambiq.com>
The target has board configuration for spi_flash sample but bacause
of the lack of SPI mentioned in supported peripherals Twister
is filtering out the target for sample.drivers.spi.flash test.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Introduce support for ST Nucleo F722ZE, an evaluation board based on
the STM32F722ZET6U microcontroller.
Signed-off-by: Evan Perry Grove <evan@4grove.com>
The `az3166_iotdevkit` board doesn't have its RTC node enabled,
and is failing the following test:
`tests/benchmarks/footprints/benchmark.kernel.footprints.pm`
Enabled RTC node for that platform.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The `96b_aerocore2` board doesn't have its RTC node enabled,
and is failing the following test:
`tests/benchmarks/footprints/benchmark.kernel.footprints.pm`
Enabled RTC node and lsi clock source for that platform.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enforce that the initial attestation partition has the required
initial attestation key provisioned.
If the initial attestation key (IAK) is not present during boot of
TF-M the system will panic during initialization.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Introduce Kconfig option in zephyr build system that reflects the TF-M
cmake config variable with the same default value for dummy provisioning
and have it satisfy the IAK present requirement.
This configuration is not suitable for production, and by having this
in zephyr configuration we can have this as part of the hardened
configuration check.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Changed the tx/rx pins in pinctrl *.dtsi files to match the
evaluation board circuit diagram for UART1.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
Change the name of the node for the lptim used as lowpower
tick source to stm32_lp_tick_source.
Once enabled, this node is known as stm32_lp_tick_source
That will avoid naming the node lptim1 or lptim2 or lptim, etc.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove BT_SPI_BLUENRG Kconfig parameter as it is redundant according to
the new changes introduced by ST SPI protocol V1 and V2.
Remove "config BT_SPI_BLUENRG" from the boards that were using it.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
The PAN1783A evaluation board is a development tool for the nRF5340
from Nordic Semiconductor.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
The `mikroe_mini_m4_for_stm32` board doesn't have its RTC node
enabled, and is failing the following test:
`tests/benchmarks/footprints/benchmark.kernel.footprints.pm`
This board seems to have been missed out from 44b8370, let's
enable the rtc & clk_lsi here.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
This is continuation of the 64fbbd9a44
where spi-flash0 alias was defined for some of boards' devicetrees.
It's needed to turn on building samples/drivers/spi_flash for boards
with "nordic,qspi-nor" compatible.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Add code to configure and program Lcu, Trgmux and Emios_Icu IPs to
get the the rotations by the motor in radians.
Co-authored-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Co-authored-by: Mayank Mahajan <mayankmahajan.x@nxp.com>
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Add support for OpenOCD runner to the Arduino Giga R1 board. This shares
the same CPU as the STM32H747i Discovery, so that implementation can be
reused.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Add the chosen dtcm memory region
for mimxrt1010_evk and mimxrt1015_evk.
To be consistent with other rt10xx platforms.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
The Adafruit Grand Central M4 Express is an ARM development board
with the form factor of an Arduino Mega.
It features 70 GPIO pins, a microSDHC slot and 8MiB of QSPI Flash.
Signed-off-by: Lukas Jung <lukas.jung@mailbox.org>
Remove disable of QSPI for BL5340 DVK cpuapp NS build.
The QSPI is not configured as a secure peripheral in the generic
nrf5340 platform support.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add pin-control configurations for UART1 pin assignments.
The GPIO pins matches the ones used in Laird Connectivity TF-M boards
RTE_Device.h file.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
SIG has changed Bluetooth mesh to Bluetooth Mesh
Updating zephyr docs accordingly
Leaving out old release notes
Signed-off-by: Mia Koen <mia.koen@nordicsemi.no>
This removes all occurrences of arm,num-mpu-regions relying on the value
reported by the register instead.
A user may still define this property if they need to have a compile time
definition for it.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
The SSE-200 implementation on AN521 only has 8 regions.
Although the AN521 FPGA image implements the documented value,
qemu-system-arm currently shows in MPU_TYPE the incorrect value of 16.
Removing the property definition allows the code to rely on the register
read value and work on both qemu-system-arm & the physical board.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Introduce minimal support for NXP UCANS32K1SIC board based on
S32K146 MCUs. This includes support to run from internal Flash or SRAM,
multiple west runners for TRACE32 and J-Link, and the minimal set of
drivers.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add boot_partition and slot1_partition for
mimxrt1010_evk and mimxrt1015_evk.
Enable MCUBoot & Flash support for them.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Rename the experimental driver overlay to be the same
for all the platforms, and document about it in the boards'
index.rst.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This commits provides USART PINCTRL configuration for efr32_radio_brd4180a
and efr32_radio_brd4187c boards.
Signed-off-by: Franciszek Pindel <fpindel@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Configure the unused pin as GPIO_DISCONNECTED for saving the power
consumption with the gpio-hog feature. The STM32 GPIO driver will
configure the pins as analog.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add overlay to show how to use new experimental nxp enet driver
Also make any eth_mcux related kconfigs dependent on eth_mcux in the
boards' defconfigs.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Changes the FS26 watchdog init priority to avoid boot-looping.
Requires SPI priority to be changed as well.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
The ATSAMD20E16 used in this board only has 8KiB SRAM, so the defaults
are not really suitable for anything close to useful, particularly the
sink sample that most closely resembles the original demo for the board.
This should also allow more tests not to be skipped for this board as
otherwise they overflow RAM usage.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
Adds the tja1103 enet phy for setting phy options on the mr_canhubk3.
Co-authored-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Adding Spider board documentation based on Renesas official documentation
and following Zephyr guideline.
The documentation is describing the board and its current
Zephyr support.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Renesas Spider board use a S4 SoC (r8a779f0).
Add basic support for UART, GPIO and clock control.
We are using SCIF0 as SCIF3 is used by Linux.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
There are duplicated names specified in per-board YAML files.
This change will allow distinguishing boards in software that
presents the pretty names and not the raw names of boards.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Make Jlink a default runner for lpcxpresso55Sxx.
The LinkServer runner command line tool does not support .hex flashing.
This feature is planned for LinkServer v1.6 (July 2024).
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
This patch changes readme files of nRF91x1 dev kits to highlight
their added NR+ feature.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
When playing with PM related applications, stm32cubeprogrammer is
useful to allow flashing even when SoC is in Stop mode.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
This is a follow-up to commit 7a83724e0f.
There is no reason to mark that many GPIO lines as reserved on this
board. And doing so causes several existing tests to fail as they
are configured to use some of those now unavailable GPIO lines.
Limit reservation to the lines that actually cannot be used as
GPIOs without changes in the default configuration of the board
or its physical modification (via solder bridges), i.e.:
- XL1 and XL2 (connections for the 32.768 kHz crystal)
- NFC1 and NFC2 (NFC antenna connections)
- RESET
- TXD and RXD (lines used by the console UART)
- QSPI lines: CS, CLK, and DIO0-3
Provide names for all the GPIO lines that are described on the board.
Even for the reserved ones, so that it is clear why they are reserved.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the WeAct Studio STM32G431 Core Board.
Tested with:
- `samples/basic/blinky`
- `samples/basic/button`
Flashed samples using dfu-util.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
This commit adds missing pinctrl configuration for USARTs in
efm32gg_slwstk6121a, efm32gg_stk3701a and efr32_radio boards
and enables PINCTRL for efr32_radio_brd4180a
and efr32_radio_brd4187c boards.
Signed-off-by: Franciszek Pindel <fpindel@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This commit moves configuration of hfxo from headers defined on board level
to device trees of SoCs.
Signed-off-by: Franciszek Zdobylak <fzdobylak@antmicro.com>
The title for this board README was very broken, messing up not only
this board's README but also the boards TOC.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Enable LinkerServer and PyOCD runners for LPC55Sx6 EVKs,
where it is supported.
It was tested on a real HW.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Add configuration lines to be able to use the jlink debugger with this
board. The disco board leaves the debug lines tri-stated until connecting
to stlink, so it is safe to just plug in the jlink and use it.
Signed-off-by: David Brown <david.brown@linaro.org>
Add Verdin iMX8M Plus board with i.MX8MP SoC and ARM Cortex-M7 processor.
Add two targets (DDR and ITCM) for the iMX8M Plus board.
Port and documentation are based on NXP MIMX8MM EVK board.
This code is intented to be used with the Cortex-M7.
Signed-off-by: Gabriel Freitas <gabriel.freitas@toradex.com>
Currently, the NXP S32 SoCs have three redundant Kconfig hidden
options to define the part number. To streamline this, we will
retain `CONFIG_SOC_PART_NUMBER` to store the part number as a
string and `CONFIG_SOC_PART_NUMBER_<part>` that can be selected
by the boards.
Furthermore, for drivers requiring conditional code compilation
based on the target SoC, they should utilize the series or SoC
config option as applicable, instead of the part number config.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The existing S32K3 Kconfig options employ the `M7` suffix, which is
redundant given that all cores in this series utilize an Arm Cortex-M7
core. Therefore, we should remove it.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add Renesas rzt2m gpio driver with basic functionality.
It supports pin mode configuration and writing/reading to/from gpio ports.
Includes dts changes to build blinky sample.
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
This adds a new driver for Renesas RZ/T2M.
The driver allows configuration of pin direction,
pull up/down resistors, drive strength and slew rate,
and selection of function for a pin.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
This adds a UART driver for the Renesas RZ/T2M
Serial Communication Interface.
The driver implements:
* Polling API,
* Interrupt-driven API.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
This adds a new SoC: SOC_RENESAS_RZT2M
and a new board: rzt2m_startek_kit
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Co-authored-by: Roman Dobrodii <rdobrodii@antmicro.com>
Added a short paragraph explaining how to use pyOCD to flash and debug this
board, as well as a disclaimer requested by NXP
Signed-off-by: Tim Guite <tim.guite@ttp.com>
Enable the gpio0 node and mux the heartbeat LED. Moreover, add the
heartbeart LED as LED node and create an alias with 'led0'.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
- Make caparray delta a Kconfig variable
- Set caparray delta for beagle_bcf at beagleconnect_freedom_defconfig
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Support NXP MRT on LPC55XXX SOC series, enable on
lpcxpresso55s69_cpu0, add test overlay to counter basic api test
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add drivers for gpio_i2c_switch which is present in beagleconnect freedom
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
Commit 944ced68f5 enabled
CONFIG_UART_CONSOLE=y for the beagleconnect_freedom board, which had the
side effect of satisfying a required dependency for the sensor shell
sample application and causing new build errors in the weekly full
twister run. Fix the build errors by moving the board's light and
humidity sensor nodes to be children of the I2C controller node.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
This patch removes the now unused scratch partition and enlarges
the application slots instead.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
This commit enables clock control instances for apollo4p_blue_kxr_evb.
Also adds pin configuration for each instance.
Signed-off-by: Aaron Ye <aye@ambiq.com>
