This board is confirmed to build and run simple applications in
RTL simulation as described in the included board documentation.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
According to the reference manual, all STM32G4 variants except
STM32G431/STM32G441 have the UART5 peripheral.
Signed-off-by: Mario Jaun <mario.jaun@gmail.com>
Boolean properties for STM32 ADC internal channels are not used anymore
and can be removed. It is replaced by channel number properties.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
In all STM32 dts, remove all reference to the following properties:
- has-temp-channel
- has-vref-channel
- has-vbat-channel
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Now that we have a binding to define the channel number for temperature
and Vref measurement, update all dtsi to include the information.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add some bindings to define STM32 ADC internal channels for:
- Temperature
- Vref
- Vbat
The goal is to transfer information to the dts instead of inside the
ADC driver.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Bugfix for the Cyclone V SoC DK ethernet driver need to add emac-index
in dts
- We remove the "local-mac-address" property from
dts/arm/intel_socfpga_std.dtsi to
boards/arm/cyclonev_socdk/cyclonev_socdk.dts, since this value is
dependant on the board / implementation and not universal to
the "intel_socfpga" package that it inherets from.
- The above is also true for the "status" property as the board
should enable the device.
Signed-off-by: Benjamin Kyd <benjamin.kyd@intel.com>
Add three xbar nodes and four qdec nodes in the rt10xx devicetree include.
Add xbara to rt1052 in Kconfig.soc
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add a driver for the NXP MCUX Quadrature Decoder. The driver
is simple and only implements the phase a and phase b inputs. The
module has additional features which can be added in future PRs.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Change the name of the custom macro defined for the stm32 devices
to fit the VND_PWM_xxx model
Keeping old deprecated macro, though.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce DT nodes for NETC complex and enable its usage for
s32z270dc2_r52 boards. Using PSI0 as default networking interface and
Switch Port0 as it's the only port available on this board.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce Ethernet low-level driver for NXP S32 Network Controller
(NETC). Current driver allows to manage from Zephyr a Physical Station
Interface (SI) and/or a Virtual SI. The NETC has an integrated Ethernet
Switch. Currently the Switch is initialized from this driver with a
default configuration, and all ports are enabled and transparent for
the user. A separate Switch driver should be addressed in future patches.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce NXP S32 NETC External MDIO controller driver. Driver supports
a single instance, as current support is based on NXP S32Z/E SoCs.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce NXP S32 Message Receive Unit (MRU) driver based
of Mbox API. The MRU couples with a processor and allows to
receive messages from senders, which are other modules or
processors.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
On STM32L4 that probvide HSI48 clock, use it as 48MHz domain clock.
This impacts following devices:
-SDMMC
-RNG
-USB
Otherwise, when HSI48 is not available MSI is used.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STMF412 and STM32F413 did not support CAN bus in Zephyr yet.
This adds the device tree entries to be able to use all 2, resp.
3 CAN controllers.
Signed-off-by: Tom Stirnkorb <tom@stirnkorb.me>
Remove the vref-mv = <3300>; property for all the ADC node of
the stm32 devices as it is set by default to 3300mV by the
dts/adc/st,stm32-adc.yaml
(Except for the stm32f303 vref is 3000mV)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Configure RNG domain clock and align it on USB (as this is the same clk).
This is not stricly required, as this configuration matches default
reset but its more consistent this way.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove SDMMC from f410 soc variant since it's not actually available.
Do this in package variant as F410 is included by f412 who has a SDMMC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide SDMMC domain clock, when required (because it is common)use
the same as the one selected by USB and RNG.
Otherwise, when available use HSI48, otherwise use the most handy (MSI,
sysclk ...).
PLLSAI is not used as not implemented for now.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add 2 properties in STM32 external interrupt controller:
- num-lines
- line-ranges
Additionally, make interrupt-names a required property.
The properties will help to simplify exti init code in building the
exti_irq_table and simplify the isr related bits.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Intel DSP Communication Widget is a device for generic sideband
message transmit/receive between IPs in a SOC.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Align RNG domain clock confguration on USB clock configuration.
For now we're not able to fully use CLK48 as a mux clock, so
this has to be done on both nodes rather than on a centralized
fashion.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The interrupt is used to wake up EC from low power mode.
So EC does not defer eSPI bus while transaction is accepted.
Fixes EC host commands slow issue.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
This commit makes the peripheral-id property optional and removes it's
usage from the Gecko SPI driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
ALH dts definitions need to have 16 nodes, thus add them to supported
platforms (cavs25 and ace15).
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
This sets the RNG node that will be used by the Nordic
devices which support TF-M (nRF5340/nRF9160) to use the
defined scheme with psa_generate_random.
Signed-off-by: Georgios Vasilakis <georgios.vasilakis@nordicsemi.no>
The documentation for the fixed-partitions binding is missing critical
information and is vague in other important respects. This is an
important binding that deserves to be crystal clear. Fix it.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Describe USB default domain clock on all USB devices.
When available select HSI48.
On some series, a default clock my be set by default at start up.
On those series, in order to be able to compute USB clock at runtime,
clock_control driver needs to be aware of configuration and then this
default config has to be described explicitly too.
Default clocks are not enabled though. It is up to board configuration
to provide correct clock configuration (and we should not enabled by
default clocks that would not be required by board configuration).
Note: This change doesn't consider STM32F1/F3 devices, which
have a specific USB clock configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add kscan pins gpio driver for KSI[7:0], KSO[15:0] pins that
they can be configured to gpio mode. These pins registers address,
bit fields and function are different from GPIO group, so I create
a new compatible driver for these pins.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
- Adds the declaration of the MMC API
- Adds MMC spec related declarations
- Adds some properties to sdhc dts binding for mmc
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
