The esp_8266 shield was added without owner on #24710. Add myself as
an owner of esp_8266 shield files.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The Atmel RF2xx module shield is a generic solution to enable any Atmel
AT86RF2xx IEEE 802.15.4 transceiver. This module enables IEEE 802.15.4
RF2xx Zephyr driver.
The Atmel RF2xx module shield enables any board with an Atmel Xplained,
Xplained-Pro, Arduino or MikroBus expansion header to connect to
networks operation with IEEE 802.15.4, OpenThread or any other stack
based on this media type.
The Atmel RF2xx module is configured to allow interoperate with other
medias like Ethernet. User need configure network stack properlly.
Fixes#26259.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add Nuvoton numicro series UART support, currently supports
only poll mode.
UART0 clock and pincontrol are directly configured, will be
replace when clock and gpio support is added.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Add initial support for nuvoton numicro m48x SoC series, basic
init and uart functionality are covered with gpio and clock
directly relies on HAL.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
This runs the Timer/Counter for Control in 'normal' PWM mode. The
number of channels and counter width depends on the device and is
imported from DeviceTree.
Signed-off-by: Michael Hope <mlhx@google.com>
- Support PLL for Higher Frequencies 80,160,240 MHz
- Support XTAL Frequencies 26MHz, 40MHz
- Clock Driver can't be disabled, because all of the other drivers
will depend on it to get their operating Frequency based on chosen
clock source (XTAL/PLL).
- Add needed references to BBPLL i2c bus ROM functions.
- Add `rtc` node to Device Tree.
- Since All Peripherals Frequency is depending on CPU_CLK Source,
`clock-source` property added to CPU node
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Add setup to utilize buildkite for CI purposes:
1. .buildkite/hooks/pre-command:
* Handles getting git checkout setup against upstream repo
* Setup some west module cache (dirs, clean out files & locks)
* init dir for ccache
2. .buildkite/hooks/post-command:
* Report disk usage (meant for possible debugging)
3. .buildkite/pipeline.yml [uses to determine what to do]:
* setup zephyr env vars
* set which docker container to use
(export some local disk caches for git, west modules, and ccache)
* uses plug to general build annotation on failure (junit-annotate)
4. .buildkite/run.sh [ buildkite wrapper to invoke scripts/ci/run.sh ]
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add infineon XMC4 series UART support. Driver supports
only poll mode using XMCLib.
Out of 4 available UART's on SoC, only UART1 is confgired
by default in UART mode until GPIO & pinctrl support.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Add infineon xmc series with XMC4500 support. XMC series comes with,
- CPU operates upto 120MHz
- 3 RAM (PSRAM1 - code, DSRAM1 - data and DSRAM2 - communiation)
- upto 1MB flash
init: clock control & gpio is not done, so SoC initialization directly
relies on HAL. Core operating clock is stored in no_init section, which
is kept under DSRAM1. Only DSRAM1 is used until clock support. Using
PSRAM1 and DSRAM1 needs adaptation in linker script - planned for next
revision.
Note: SystemInit cannot be consumed directly due to vector table +
HAL linker dependency.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
This change enables specific compiler and linker options to be used in
the case that an arch/posix/os.arch.cmake file exists.
Note: os and arch in the above case are evaluations of
CMAKE_HOST_SYSTEM_NAME and CMAKE_HOST_SYSTEM_PROCESSOR.
Otherwise, the existing "generic" compiler and linker flags in
arch/posix/CMakeLists.txt are used.
Additional flags and checks are provided in
arch/posix/Linux.aarch64.cmake.
Added scripts/user_wordsize.py to detect if userspace is 64-bit or
32-bit, which should be consistent with the value of CONFIG_64BIT
for Aarch64 on Linux.
Fixes#24842
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Add a disk access driver for the stm32 sdmmc component. The driver is
based around the stm32 cube HAL and uses the blocking API.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Many chips have only one serial port. When the serial port is occupied
by other devices, there is a lack of a console to output debugging
information. Semihosting can provide a console. The disadvantage of
semihosting is that a debugger must be connected, so it can only be
used for online debugging.
Signed-off-by: ZhongYao Luo <LuoZhongYao@gmail.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Cloned from counter_basic_api with modifications based on DS3231
limitations:
* Only one device tested per board;
* Counter cannot be stopped or started;
* Alarms are serviced by worker thread, so are not invoked from ISR
and require that test thread yield to allow processing (no
k_busy_wait());
* Multiple Alarms test is disabled as documented in test.
Additional tests were added for DS3231-specific API.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The DS3231 is an I2C real-time clock with internal temperature
compensated oscillator, maintaining civil time to 1 s precision with
nominal 2 ppm accuracy from 0-40 Cel.
The basic functionality is exposed as a counter that is always running
at 1 Hz. Much more functionality is exposed as driver-specific API,
including the ability to translate between the time scale of the DS3231
and the time scale of the Zephyr uptime clock. This allows correlation
of events in the system clock to UTC, TAI, or whatever time scale is
used to maintain the DS3231.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit renames the CAN sample directory name from `CAN` to `can`
to be consistent with others.
Noting that the CAN driver test directory is named `tests/drivers/can`,
we have no excuse for naming the CAN driver sample directory
`samples/drivers/CAN`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
DAC (digital to analog converter) peripheral driver with a generic API
suitable for most MCUs (only basic DAC features considered).
Signed-off-by: Martin Jäger <martin@libre.solar>
Add pinctl support for the SAM UART and SAM USART devices. We update
the UART and USART bindings to have pinctrl-0 bindings that are expected
to have 2 phandles to the RX & TX pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We add sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This GitHub account has been disabled for over a year (it was replaced
by a `ricardosalveti` account). Remove from CODEOWNERS.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This sample now supports SMP UDP transport.
Two config overlays have been added for ipv4 and ipv6, respectively.
The sample documentation has been completely revamped to be less
bluetooth focused and more general.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
Add code owners for nRF UART drivers and the corresponding Kconfig file
so that some reviewers are automatically assigned for these files.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
k_poll() for a signal is often desired for notification of completion
of asynchronous operations, but there are APIs where it may be
necessary to invoke "asynchronous" operations from contexts where
sleep is disallowed, or before the kernel has been initialized.
Extract the general notification solution from the on-off service into
a utility that can be used for other APIs.
Also move documentation out to a resource management section.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The resource table is needed by the Linux kernel OS
for a rpmsg generic support, but is also recognised by OpenAMP.
This table allows to add trace based on the RAM console
and to support rpmsg protocol.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Fixes: #23872
Relocating Zephyr Unittest CMake package to ensure that
HINTS ${ZEPHYR_BASE} in
find_package(ZephyrUnittest HINTS ${ZEPHYR_BASE}) works correctly when
the package has not been exported to CMake user package registry.
This ensure that the new package functionality is fully backwards
compatible on systems where the package is not exported and ZEPHYR_BASE
is set.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Add @nandojve, the SAM V71 platform maintainer, as a code owner for
the SAM E70 platform, as these two platforms share the same base and
are practically identical.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Transfer review assignments from SebastianBoe to tejlmand.
Sebastian Bøe's role is being transferred to Torsten
Rasmussen (tejlmand).
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Adding ZephyrConfig.cmake and ZephyrConfigVersion.cmake allows projects
to use find_package to locate Zephyr.
This means that it will be possible to allow users to run CMake without
the need to source zephyr-env.sh or run zephyr-env.cmd.
This is especially useful for IDEs such as Eclipse or SES, where it will
no longer be required to source the above files before launching the
IDE.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This commit renames the `cortex_r` directory under the AArch32 to
`cortex_a_r`, in preparation for the AArch32 Cortex-A support.
The rationale for this renaming is that the Cortex-A and Cortex-R share
the same base design and the difference between them, other than the
MPU vs. MMU, is minimal.
Since most of the architecture port code and configurations will be
shared between the Cortex-A and Cortex-R architectures, it is
advantageous to have them together in the same directory.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This adds a rather primitive driver for use with the Intra-DSP
Communication (IDC) on the DSP on certain Intel SoCs. The IDC
generates interrupts from one core to another by writing to
certain registers. This is also being utilized as
the scheduler IPI since it can interrupt other cores.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The DSP wall clock timer on some Intel SoC is a timer driven
directly by external oscillator and is external to the CPU
core(s). It is not as fast as the internal core clock, but
provides a common and synchronized counter for all CPU cores
(which is useful for SMP).
This uses the RISCV timer as base as it is using 64-bit
counter.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add @stephanosio as a code-owner for the tests/arch/arm
test suites, so they get auto-assigned in reviews.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds basic testcases for sanitycheck tool using pytest.
Coverage for the sanitycheck tool is obtained using coverage tool.
Instructions are included in the README.md in
scripts/tests/sanitycheck directory.
Signed-off-by: Aastha Grover <aastha.grover@intel.com>
This commit introduces boards/deprecated.cmake to allow deprecation
of existing boards, when a board is renamed.
This allows users to still specify the old board name, and let Zephyr
build system to select the new board name.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This commit reworks the Xilinx TTC timer driver to use the "match" mode
instead of the "interval" mode which counts up to the specified value
and resets to zero.
Using the "match" mode ensures that the timer keeps counting even after
an interrupt is triggered, and facilitates the tickless mode support
implementation.
This also allows `z_timer_cycle_get_32` to return the correct cycle
count when interrupt is locked; thereby, fixing the k_busy_wait hang
issue.
Note that the TTC "match" mode emulation (and tickless timer operation)
is only stable when the QEMU icount mode is enabled.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Since we already have similarly licensed 3-clause BSD files in the tree,
and in particular in our minimal libc, move the fnmatch functionality
from ext/ to lib/.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
IP ethernet switch board includes K66F MCU from NXP
and Micrel/Microchip KSZ8794CNX switch. Board support
includes basic GPIO LED and common functions.
Switch function needs support either based on DSA or
relative feature in Zephyr which is tracked with issue
22061.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Add entropy driver based on GECKO TRNG module along with device
tree support for EFM32PG and EFR32MG SOCs.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
Split up requirements.txt into several files so that CI tools can
utilize/reference the specific requirements-<FOO>.txt they may need
while keep things in sync with the development. This is to reduce
both time and amount of work CI actions due to python package install.
Create the following groupings:
1. BASE - needed to build or create zephyr images
2. BUILD-TEST - need to run compile/build tests
3. DOC - need to build the docs
4. RUN-TEST - need for runtime testing
5. EXTRAS - optional or useful for development/developers workflow
Also tried to add a comment about what or why a given package is being
pulled in for.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This never needed to be put in a separate gperf table.
Privilege mode stacks can be generated by the main
gen_kobject_list.py logic, which we do here.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add Platform Environment Control Interface API
This API defines following calls:
- peci_configure
- peci_enable
- peci_disable
- peci_transaction
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
daor-oti and wopu-ot also want to be added automatically as
reviewers to POSIX arch, native_posix, nrf52_bsim and bsim
related test apps.
(see CODEOWNERS for more info about which each is interested on)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Add @stephanosio as a code owner for the Xilinx ZynqMP platform, which
is used as the primary testing platform for the Cortex-R architecture.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Replace running west command tests in run_ci.sh with a github workflow.
This provides some benefits in that we can run the west command tests on
multiple python versions and host OSes (linux, mac and windows).
Also have the benefit that the tests are only run on modifications to
files in scripts/west_commands/ or scripts/west-commands.yml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add script to capture tracing stream data with UART backend. This
script is developed based on pyserial, so install it correctly
before using the script.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
This commits adds GPIO driver for LiteX SoC builder.
Due to the fact that GPIO in LiteX is unidirectional and can be
configured with different pins amount per port, additional entries
were added to the dts file.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API.
Tested on external SX1509B breakout board and Thingy:52.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Test that the new port API functions all behave as expected, including
physical vs logical level for input and output as well as masked and
set-based output operations. Also tests the new pin API functions.
For running on real hardware this test now uses a local test-specific
devicetree binding. For build-only tests any platform with a GPIO
alias should be tested.
The new code increases flash requirements so add a filter to exclude
platforms that won't link.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Watchdog type is found on e.g. Pearl/Jade Gecko, often
more than 1 is present.
Driver supports timeout and (minimum) window configuration
and reset or timeout interrupt support for now.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Add a script that sets up Docker networking and starts the net-tools
Docker container. If successful, run Zephyr with native_posix and
execute the appropriate net-tools container executable. The proper
net-tools executable and arguments is selected depending on the
basename of the sample directory. This script needs to be updated
if the net-tools Docker image is updated in some incompatible way.
The net-tools directory is assumed to exist at the same level as
the Zephyr base directory, but its location can be set using the
'-N' command line argument. Likewise, '-Z' sets the Zephyr top level
directory.
When stopping Zephyr, go through all child processes since running a
native posix or other variant of Zephyr may cause a hierarchy of
processes to be created.
Fixes: #19540
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Introduce the basic ARM64 architecture support.
A new CONFIG_ARM64 symbol is introduced for the new architecture and new
cmake / Kconfig files are added to switch between ARM and ARM64.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
ARM cores may have a per-core architected timer, which provides per-cpu
timers, attached to a GIC to deliver its per-processor interrupts via
PPIs. This is the most common case supported by QEMU in the virt
platform.
This patch introduces support for this timer abstracting the way the
timer registers are actually accessed. This is needed because different
architectures (for example ARMv7-R vs ARMv8-A) use different registers
and even the same architecture (ARMv8-A) can actually use different
timers (ELx physical timers vs ELx virtual timers).
So we introduce the common driver here but the actual SoC / architecture
/ board must provide the three helpers (arm_arch_timer_set_compare(),
arm_arch_timer_toggle(), arm_arch_timer_count()) using an header file
imported through the arch/cpu.h header file.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The Silicon Labs EFM32 Jade Gecko MCU includes:
* Cortex-M3 core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* multiple low power peripherals
This is basically the same as the EFM32 Pearl Gecko, but with an ARM
Cortex-M3 core instead of a Cortex-M4F.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
There are various situations where it's necessary to support turning
devices on or off at runtime, includin power rails, clocks, other
peripherals, and binary device power management. The complexity of
properly managing multiple consumers of a device in a multithreaded
system suggests that a shared implementation is desirable. This
commit provides an API that supports managing on-off resources.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit adds initial support for the Silicon Labs EFM32
Giant Gecko GG11 StarterKit.
Features supported for now are NVIC, SysTick, GPIO, Flash,
Counter, I2C, UART and Ethernet. Support for Watchdog and
ADC will follow as soon as their respective PRs are merged.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Add support for storing the CANopen object dictionary to non-volatile
storage.
This fixes#15278.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add a Zephyr driver and abstraction layer for use by the 3rd party
CANopenNode module.
CANopenNode depends on the CO_driver.h file for platform-specific type
definitions, locking primitives, and CAN bus driver API.
This fixes#15278.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move LVGL sample from samples/gui/lvgl to samples/display/lvgl to have
a unified location for display related samples.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
As of January 2020, David is no longer working on the Zephyr
documentation, so he should not be automatically added as reviewer.
I've commented out rather than removed the lines so when a replacement
is found, the lines can easily be added back.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add driver for the Texas Instruments LMP90xxx series of multi-channel,
low-power 16-/24-bit sensor analog frontends (AFEs).
The functionality is split into two drivers; an ADC driver and a GPIO
driver.
Tested with LMP90080 and LMP90100.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
