We might have to do this differently:
Configure rng default clock in .dtsi
Set board specific config in .dts
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
SRAM6 is used by RF and should be defined as RAM_NOCACHE
to allow unaligned access reads.
"IO" might be a better match but is not available on this arch.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F722 is similar to the STM32F723, but lacks the latter's
more advanced USB PHY. Otherwise, they are virtually identical.
Signed-off-by: Evan Perry Grove <evan@4grove.com>
Add SMBus devices to all SoCs which have either
a st,stm32-i2c-v1 or st,stm32-i2c-v2.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
The commit fixes the SHA driver because the ROM API has the following
changes from ES to QS chip:
1. base addres: from 0x13c -> 0x148
2. required SHA context buffer size : from 228 -> 240 bytes
This change also adds a check for the pre-allocated buffer size of the
SHA context when the driver initiliazes.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
This patch adds definitions for the nRF9151,
which is software-compatible with nRF9161.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Add `compatible` node to Ambiq SoCs, along with secondary common compat,
since they share many similarities.
Signed-off-by: Mateusz Karlic <mkarlic@antmicro.com>
Add code to configure and program Lcu, Trgmux and Emios_Icu IPs to
get the the rotations by the motor in radians.
Co-authored-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Co-authored-by: Mayank Mahajan <mayankmahajan.x@nxp.com>
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Based on stm32wba55, stm32wba55Xg is similar from device tree description
to stm32wba52Xg.
Take the opportunity to fix stm32wba52Xg descriuption scheme which was
missing stm32wba52.dtsi.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Fixes an issue with the register addresses which was caused by a
missing `ranges;` option for the power peripheral
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This PR set the correct value for the stm32F7 devices.
And change vrefint-cal-addr to <0x1FF07A2A> for stm32F722-F723
soc serie.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Use the "ambiq,gpio" binding to combine the "ambiq,gpio-bank"
child nodes for Apollo4 Plus soc.
Also update the GPIO driver accordingly.
Signed-off-by: Aaron Ye <aye@ambiq.com>
This removes all occurrences of arm,num-mpu-regions relying on the value
reported by the register instead.
A user may still define this property if they need to have a compile time
definition for it.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Although the RT1015 only supports 128 KB of FlexRAM being used at once, the
default fusemap overallocates 160KB of FlexRAM. The JLink flashloader
algorithm appears to rely on the 64KB of DTCM in the default fusemap
being configured. Reducing the DTCM allocation resulted in JLink
failing to flash the SOC.
To resolve this, utilize the default fusemap of {O, O, D, D, I} for the
RT1015 FlexRAM setup. Add a note about the restrictions on using
overallocated FlexRAM to the SOC DTSI.
Fixes#65889
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Adds the tja1103 enet phy for setting phy options on the mr_canhubk3.
Co-authored-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
The number of IRQ priority bits was incorrectly set to 3 instead
of 2, which is the correct number for Cortex-M0+.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
After porting from h5 to f7 i noticed that not all mcus have
cpu node labels. Added cpu0 node labels to all stm32 dts.
Signed-off-by: Kacper Dalach <dalachowsky@gmail.com>
r8a779f0 is also know as S4, this SoC is part of the Gen4 SoC series,
has 8 Cortex-A55 and a dual core lockstep Cortex-R52 processor.
SCIF0 is dedicated to Zephyr and SCIF3 to Linux.
**Control Domains**
IMPORTANT: This SoC is divided into two "domains":
- Application domain contains some peripherals as well as A55 & R52 cores.
- Control domain that contain a G4MH/RH850 MCU and other peripherals.
In order to access control domain peripherals such as gpio4-7 and CAN-FD
from application domain, the G4MH MCU has to unlock a protection
mechanism from control domain buses.
"Protected" controllers will be flagged in gen4 device trees,
warning users that they need to flash a custom G4MH firmware
to unlock access to these controllers.
**Clock controller**
This SoC clock controller is offering "domains"
for each world (Zephyr/Linux).
These domains are several "entry points" to the clock controller
which are arbitrated to avoid a world from turning off a clock needed
by another one.
We decided to use the same domain as Linux because the
security mechanism as to be implemented before accessing
another domain.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
The shi module in npcx4 supports the enhanced buffer mode.
Add a new compatible string "nuvoton,npcx-shi-enhanced" for it.
Then the shi driver can determine if it should use the enhanced buffer
mode based on the compatiable string.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
This add regulator driver for Smartbond DA1469X SOC.
Driver can control VDD, V14, V18, V18P, V30 rails,
full voltage range supported by SOC is covered.
For VDD, V14, V18, V18P DCDC can be configured.
Special VDD_CLAMP (always on) and VDD_SLEPP are added
to allow configuration of VDD in sleep modes.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Only RTC can be used as the idle timer for cortex-m systick. Set the
chosen node as RTC by default.
The idle timer will be enabled only if PM management is set.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Rather than configuring in serial_wakeup sample, define LPUART1 wakeup
line in wl.dtsi file.
Additionally make few cosmetic changes to nucleo_wl55rj overlay in
serial wakeup sample.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Add soc power management for the STM32F4x chips.
One low power state is added supported by all chips from the family -
the Stop mode with voltage regulator in low-power mode.
The Stop mode for STM32F chips has to work with the IDLE timer -
CORTEX_M_SYSTICK_IDLE_TIMER, because PLL and HSI are disabled in the
Stop mode (Systick is not clocked). The only possible wakeup source is
RTC, which works as a IDLE timer for the Systick.
The exit latency may need to be adjusted per system, depending on the
system tick frequency and other variables.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
On STM32WL, the backup memory is defined as part of the TAMP peripheral.
This seems to be a deviation from the stm32 family where this memory is
defined as part of the RTC.
The STM32WL reference manual shows that tamp_pclk is connected to
rtc_pclk. This means that the clock required to run the TAMP peripheral
is the same as the RTC's. A quick port of BBRAM on STM32WL is achieved
by instanciating the bbram device as a child of the RTC and by modifying
the address offset to the first backup register from the rtc base
address.
Signed-off-by: Adrien Bruant <adrien.bruant@aalberts-hfc.com>
This commit moves configuration of hfxo from headers defined on board level
to device trees of SoCs.
Signed-off-by: Franciszek Zdobylak <fzdobylak@antmicro.com>
Add Verdin iMX8M Plus board with i.MX8MP SoC and ARM Cortex-M7 processor.
Add two targets (DDR and ITCM) for the iMX8M Plus board.
Port and documentation are based on NXP MIMX8MM EVK board.
This code is intented to be used with the Cortex-M7.
Signed-off-by: Gabriel Freitas <gabriel.freitas@toradex.com>
Add support for UART1 usage by adding uart1 node and configuration
to the i.MX 8ML devicetree include.
Signed-off-by: Gabriel Freitas <gabriel.freitas@toradex.com>
Add Renesas rzt2m gpio driver with basic functionality.
It supports pin mode configuration and writing/reading to/from gpio ports.
Includes dts changes to build blinky sample.
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
This adds a new driver for Renesas RZ/T2M.
The driver allows configuration of pin direction,
pull up/down resistors, drive strength and slew rate,
and selection of function for a pin.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
This adds a UART driver for the Renesas RZ/T2M
Serial Communication Interface.
The driver implements:
* Polling API,
* Interrupt-driven API.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
This adds a new SoC: SOC_RENESAS_RZT2M
and a new board: rzt2m_startek_kit
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Co-authored-by: Roman Dobrodii <rdobrodii@antmicro.com>
Enable NXP FlexRAM in DTS and SOC code.
Do not configure flexram at runtime if the code is in the RAM.
Fix RT1060 DT to be more accurate.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
