Using the SOC_IT8XXX2_REG_SET_V2 instead of constantly adding new
variants of the IT82XX2 SoC.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This adds automatic GPIO latching before going to extended sleep and
restoring state after wakeup.
Mode and state for each pin is stored, then ports are latched to retain
state when PD_COM is disabled during sleep. On wakeup mode and state for
each pin is restored and ports are unlatched to make it work again.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This enables cache retainability while in sleep so there's no penalty
when executing from QSPI after wakeup.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
This enabled extended sleep for Renesas SmartBond(tm).
Extended sleep is low power mode where ARM core is powered off and can
be woken up by PDC. This is default sleep mode when CONFIG_PM is
enabled.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This adds timer driver for Renesas SmartBond(tm) family.
It uses TIMER2 block which is in PD_TIM power domain so it can work even
if ARM core is disabled, thus can work as a sleep timer.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Remove CONFIG_NRF_ENABLE_ICACHE as it is not needed. There is CONFIG_ICACHE
which is by default enabled for nrf54h.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The AM64x and AM62x are both SOCs from the TI K3 family
and share common architecture designs. The M4F subsystem
is actuall identical on both SOCs.
Therefore, just add all missing CONFIGs, files, etc. to
support the AM6442x SOC.
Since MMR and RAT initialization are identical too, both
functions can be re-used. However, since they might
differ in the future, the am64x has it's own init
function.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
This implements basic driver to utilize the I3C IP block
on NPCX.
1. I3C mode: Main controller mode only.
2. Transfer: Support SDR only.
3. IBI: Support Hot-Join, IBI(MDB).
Controller request is not supported.
4. Support 3 I3C modules:
I3C1(3.3V), I3C2(1.8V, espi mode), (I3C3 1.8V or 3.3V)
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
1. The only valid values of MCLKD clock frequency
are between 40Mhz to 50Mhz.
2. If DMA is used, the APB4_CLK clock frequency must
be equal to or higher than 20Mhz.
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
Prevent the CPU from entering deep doze mode when JTAG debug is enabled.
Additionally, The CPU address from 0x80000800 to 0x800008FF should be
reserved for JTAG debug usage. This commit reserves the area from the end
of the reset section to 0x800008FF if JTAG debug is enabled.
Tested with:
- west build -p always -b it82xx2_evb samples/hello_world/
-DCONFIG_SOC_IT8XXX2_JTAG_DEBUG_INTERFACE=y
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
Real Time peripherals should be enabled by default.
Add a common initialization point for all VPRs and enable them.
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
IRQ handling functions are now in interrupt controller.
Enable necessary KConfigs to support CLIC properly.
A nice side effect of enabling RISCV_PRIVILIGED is that
`vector.S` is no longer necessary as common code handles
that.
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
Fixed order of mepc and _mcause in esf for 32bit stacking.
Added missing stack pointer alignement bit support.'
Signed-off-by: Lukasz Stepnicki <lukasz.stepnicki@nordicsemi.no>
RISCV_PRIVILEGED implicitly depends on INCLUDE_RESET_VECTOR.
Remove that dependency by adding support for SoCs that
do not need the `__reset` stub.
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
For more effective code execution on STM32 devices is convenient
to enable flash prefetch buffer.
To be enabled by default, possible to disable using kconfig.
Signed-off-by: Lubos Koudelka <lubos.koudelka@st.com>
Fixes#71511
Follow-up to #70977
Update the approach by moving the `PROVIDE` directive to a separate
linker script added using `zephyr_linker_sources()`. This makes the
change more likely to propagate to existing samples which are using
CONFIG_CUSTOM_LINKER_SCRIPT.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Move the cache size set calls from soc.c do common loader.c
for all related SOCs. Remove unnecessary includes.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
The dependencies should be in a 'depends on' clause.
Also, 'depends on PTP_CLOCK' is redundant because this is
within 'if PTP_CLOCK' already.
Additionally, conditionally include the PTP header in the mac driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Variant chip has different USBPD HW PHY, so FW needs
to apply different downstream CONFIG settings based on
the PHY version.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Nuvoton NPCX chips have reset registers which allow to reset the
peripheral hardware modules. This commit adds the support by
implementing the reset driver. Note that only the reset_line_toggle API
is supported because of the nature of the reset controller's design.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Asm is notoriously harder to maintain than C and requires core specific
adaptation which impairs even more the readability of the code.
This change reduces the need for core specific conditional compilation and
unifies irq locking code.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
# Conflicts:
# soc/arm/nordic_nrf/nrf53/soc_cpu_idle.h
A workaround to avoid icache corruption was added in commit be881d4cf2
("arch: xtensa: add isync to interrupt vector").
This patch implements a different workaround by adding custom logic to
idle entry on affected Intel ADSP platforms. To safely enter "waiti"
when clock gating is enabled, we need to ensure icache is both unlocked
and invalidated upon entry.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
This commit introduces a common API for managing nRF53 SoC network CPU
Force-OFF state.
From the application CPU point of view, the network CPU is a shared
resource used by multiple users. The current solution where every user
controls the network core state directly leads to dependencies between
users and does not scale well.
To address this problem there should be a single entity responsible for
controlling the network CPU Force-OFF signal. This commit introduces
such module.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Add code to clock and release reset signal for USBOTG controller on
RW6xx SOC when USB is enabled, and add KConfig selection to indicate to
build system which USB controller this SOC uses.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
IPC has inverted the usage of the state lock API.
In this API semantics, the get method disallow the policy of
using the given state, while the put() release this constraint.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Fix the inline documentation to match implementation. As IPFL is used,
the correct matching function is xthal_icache_region_lock().
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Fix the inline documentation to match implementation. As IPFL is used,
the correct matching function is xthal_icache_region_lock().
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Nordic SoCs use this hook to execute `SystemInit` as early as possible
after ARM core reset. Previously, `z_arm_platform_init` was defined as
assembly code, which would simply jump to the other function.
However, this extra code can be avoided by using `SystemInit` directly
in place of the `z_arm_platform_init` symbol (whenever it's undefined).
This is now done with a linker script containing a `PROVIDE` directive.
This saves 4 bytes of ROM (0-16 depending on alignment) and also makes
it possible to override `z_arm_platform_init` out of tree, if needed.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
