Flash erase-block-size is 2048 for F030xC, F070xB, and F071 and higher.
For all others, it is 1024, default value in base dtsi.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Remove calibrated temperature measure from base dtsi since it does not
exist for STM32F0x0, and add it only for the other STM32F0.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Fix DMA1 interrupt channels. There are 7 for STM32F071 and higher, and 5
for all others, default value for the series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Remove TIM6, 7 & 15 from base dtsi, and add TIM6 & 15 to F030x8, TIM7 for
F030xC, TIM15 for F070, TIM6 & 7 for F070xC, TIM6 & 15 to F051, and TIM7
for F071.
Remove TIM2 from F072 and F091 dtsi since it is already included in F031.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Modify the successive dtsi include to better reflect the underlying
structure of the F0 family.
There are two main subfamilies: STM32F0x0 on one side, and STM32F0x1, x2
and x8 on the other
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Fixes the warning below. This commit does not change the firmware
binary. Thanks Kumar Gala for the suggestion.
build-mtl/zephyr/zephyr.dts:279.42-285.5: Warning (simple_bus_reg):
/soc/ace_comm_widget@71C00: simple-bus unit address format error,
expected "71c00"
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Add driver for Xptek XPT2046 resistive touch controller on SPI.
Only interrupt driven mode supported, does not do polling.
Signed-off-by: Seppo Takalo <seppo.takalo@iki.fi>
- Add overlay for the esp32c3 board to die_temp_polling sample.
- Add aliases for the die_temp_polling sample to esp32c3 dtsi.
Testing Environment:
esp32c3-devkitC-02
Signed-off-by: Hiroki Tada <tada.hiroki@fujitsu.com>
Introduce driver for NXP DCNANO LCDIF (lcd interface) peripheral,
present on iMX.RT500. Currently this driver only supports updating
the primary framebuffer, and does not implement support for the cursor
buffer present on this IP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce driver for MCUX MIPI DSI 2L. This IP block differs slightly from
the existing MCUX MIPI peripheral, and uses a different hardware
abstraction layer. For these reasons, a new driver was introduced rather
than extending the existing mcux_dsi implementation.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Allow configuration of AHB RX buffer allocation. This allows sections
of the AHB RX buffer to be reserved for specific masters, which can
enhance performance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
STM32L432 SDMMC issue
RM0394 :SDMMC
Not available on STM32L42xxx, STM32L432xx and STM32L442xx devices.
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
The driver utilizes ST Microelectronics library (which
exists in modules\hal\st\sensor\vl53l1x. Platform specific
headers and source files used by the library are included
and adapted for Zephyr.
The driver can be configured in proj.conf to use a
interrupt/polling methods and the use of the XSHUT pin on
the VL53L1X. All uses were tested successfully.
Signed-off-by: Mark Watson <mwatson@prosaris.ca>
This patch adds watchdog driver for Renesas Smartbond SOCs.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds driver for SmartBond TRNG peripheral that with separate
ISR an thread data pools.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Add support for configuring power on delay when using SPI SDHC. This
allows cards that reliably initialize with a shorter (1ms) delay to
avoid the long initialize delay otherwise imposed.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add I2C bus recovery support to the STM32 v1 and v2 driver. The STM32 i2c
peripheral does not natively support I2C bus recovery so recovery is
performed using GPIO bitbanging. This mirrors the bus recovery
implementation for NXP MCUX LPI2C driver.
Fixes: zephyrproject-rtos#54917
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
Microchip XEC devices specify GPIO pin using octal numbering and
organize pins in banks of 32. Chip documentation does not use
bank naming rather naming each pin by its octal number. This has
led to the developer having to calculate the bit position of a pin
in its 32-bit bank when a specifying the pin for GPIO usage. We
created a set of defines for all possible GPIO pins that specify
the DT GPIO bank name used in the chip level DTSI files and the
bit position in that bank.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The dma-requests specified for dmamux is changed to
the correct number of 107. This can be found in the
Reference Manual RM0455 Section 17.1.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Extends dmamux driver to support DMAMUX 2,
which supports the BDMA on STM32H7 devices.
Co-authored-by: Jeroen van Dooren <jeroen.van.dooren@nobleo.nl>
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
update MEC172x adc driver to support device PM.
Implement pm resume and suspend actions to put adc
pins in proper state for suspend and resume.
Notify kernel of busy when adc sampling is in progress.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Added initial version of Infineon CAT1 GPIO driver.
Added initial version of binding file for Infineon CAT1 GPIO driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 UART driver.
Added initial version of binding file for Infineon CAT1 UART driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Add initial version of Infineon CAT1 clock control driver.
- supports clock initialization based on board DT configuration.
Added initial version of system_clocks.dtsi for Infineon PSoC 6 SOC.
Includes: clk_imo, path_mux0..4, fll0, pll0, clk_hf0..4, clk_fast,
clk_slow and clk_peri.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 Pin controller driver.
Added initial version of binding file for Infineon CAT1 Pinctrl driver.
Added initial version of dt header for Infineon CAT1 pinctrl driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Devicetree for Infineon PSoC 6 SOC with following
structure:
1. MPN devicetree files
|--> psoc6
|--> mpns
|--> CY8C6016BZI_F04.dtsi
|--> CY8C6036BZI_F04.dtsi
|--> CY****.dtsi
Those file describes cpus, flash-controller, sram memory, nvic option. It
includes the package dtsi (e.g. psoc6_02.124-bga.dtsi) with information
about gpio (based on package e.g. 68-qfn, 128-tqfp, 124-bga, etc.) and
peripherals for (based on PSoC 6 series, psoc6_01, psoc6_02, etc).
MPN devicetree file is main platform dtsi file, which should be included
from board dts (e.g cy8cproto_062_4343w.dts), example:
#include <infineon/psoc6/mpns/CY8C624ABZI_S2D44.dtsi>
2. Devicetree files for PSoC 6 series 02 (2M).
Includes: psoc6_02.dtsi - peripherals dtsi psoc6_01.xxxxx.dtsi - package
dtsi. User does not directly include those files.
It automatically includes via MPN dtsi.
|--> psoc6_02
|--> psoc6_02.dtsi
|--> psoc6_02.100-wlcsp.dtsi
|--> psoc6_02.124-bga.dtsi
|--> psoc6_02.128-tqfp.dtsi
|--> psoc6_02.68-qfn.dtsi
In future PR/commits will be added Devicetree for support all
PSoC 6 series:
- for PSoC 6 series 01 (1M)
- for PSoC 6 series 03 (512)
- for PSoC 6 series 04 (256)
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Provide dts binding for F412 PLL I2S.
This I2S dedicated PLL is fully configurable and take same
input as Main PLL
Only one output clock (PLLR) is supported for now.
This PLL could be found on STM32F412 and F413 parts for instance.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide dts binding for F4 PLL I2S.
This PLL share input source and input M diviso with F4 Main PLL.
Only one output clock (PLLR) is supported for now.
This PLL could be found on STM32F401 parts for instance.
Additionally, provide related header definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Polarity support added to XEC PWM driver. This allows (for example) PWM
controlled LEDs that are active low to actually be turned off when set
to off.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Rework the Host Command support. It includes:
-change API to backend
-change a way of defining rx and tx buffers
-fix synchronization between the handler and backend layer
-simplify the HC handler
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Follow naming pattern in the subsystems(logging or shell) and name
the layer between generic handler and peripheral driver "backend".
The name doesn't suit that well to the SHI backend, because there isn't
SHI API itself and the SHI interface is used only for the host
communication. So the backend code includes the peripheral driver itself.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Change the dtsi order for the stm32L4plus serie,
starting with stm32l4p5-stm32l4q5 and stm32l4r5-stm32l4s5
Significant changes are on the SRAM size, the sdmmc2
and separated RTC-bbram registers.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The SRAM1(total 192 KBytes) plus SRAM2: (total 64 KBytes)
plus SRAM3(total 512 KBytes) is available from 0x20000000 to
0x200BFFFF.
The SRAM size is only 768KB at address 0x20000000
The 16KB SRAM4 is located at address 0x28000000 so that no ram
is present from 0x200c0000 to 0x28000000.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the implementation for the akm09918c magnetometer driver.
Additionally, add the appropriate node to the TDK robokit1 device
tree. In order to prevent regressions, add the sensor to the sensor
build_all tests and specific tests using an emulator.
Signed-off-by: Yuval Peress <peress@google.com>
Add a driver implementation that uses the I2S peripheral.
Based off this blog post:
https://electronut.in/nrf52-i2s-ws2812/
Should help with #33505, #29877 and maybe #47780, as there is no garbage
data at the end of transmissions on nRF52832, and no gaps.
Signed-off-by: Jonathan Rico <jonathan@rico.live>
Some register addresses change within the AM6X family.
AM62X is common to AM623X/AM625X processors.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
STM32L4plus mcu has SDMMC internal DMA which works without any
configuration and it's handled by SDMMC HAL driver. This commit adds
option to enable it and use it.
Signed-off-by: Petr Hlineny <development@hlineny.cz>
For STM32L47x and STM32L48x, the high calibration value for temperature is
110. For all other STM32L4xx, it is 130. So we set 130 by default and set
it to 110 for L471.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
ADC3 is already defined for STM32L471 which is included in STM32L476 and in
STM32L496 so no need to define it a second time.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Move LPTIM2 from stm32l431 dtsi to the general stm32l4 dtsi since all
STM32L4xx have two LPTIMs.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Create and use a new `zephyr,i2c-target-eeprom` compatible
within I2C eeprom target driver that allows to use
that driver along with real atmel at24 EEPROM simultaneously.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Microchip's PolarFire SoC has a core complex consisting of one e51
monitor core and four u54 application cores. Add the remaining cpu nodes
to mpfs-icicle device tree. Add the software and timer interrupt irq's
to the clint for the additional cpu nodes.
Signed-off-by: Conor Paxton <conor.paxton@microchip.com>
Update machine timer drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on NIOSV devicetree.
Signed-off-by: Khor Swee Aun <swee.aun.khor@intel.com>
All STM32H7 variants seems to have two fd-can interfaces available. Add
a can2 definition in stm32h7.dtsi, drop the current one in
stm32h723.dtsi. Also drop the override of address/size cells, this node
is not supposed to have any child node so they are not needed.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
This commit adds access to the string values without a quotes.
Signed-off-by: Radosław Koppel <r.koppel@k-el.com>
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
rt1064 already includes dtsi file for rt1060, including values for ARM and
IPG PODFs. Drop explicit assignment of those PODF values in order to reduce
duplicated code.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
