Add overlay to show how to use new experimental nxp enet driver
Also make any eth_mcux related kconfigs dependent on eth_mcux in the
boards' defconfigs.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Changes the FS26 watchdog init priority to avoid boot-looping.
Requires SPI priority to be changed as well.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
The ATSAMD20E16 used in this board only has 8KiB SRAM, so the defaults
are not really suitable for anything close to useful, particularly the
sink sample that most closely resembles the original demo for the board.
This should also allow more tests not to be skipped for this board as
otherwise they overflow RAM usage.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
Adds the tja1103 enet phy for setting phy options on the mr_canhubk3.
Co-authored-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
The existing npm1300_ek shield overlay has several example
voltage and gpio settings. For many use cases these are
invalid and need to be overridden, or removed with
delete-property.
These example configurations have been moved to a board
specific overlay.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Some native_posix specific apps/tests use the macro NEVER
provided it also for native_sim until all have switched
to the new NSI_NEVER.
And ensure NSI_NEVER is also avaiable when building
for native_posix to ease the transition.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Get the native_posix DTS from native_sim instead of
the oposite. As native_sim is now the default test platform.
Note this commit is practically just swapping files.
There is no changes to the DTS content, beyond
changing the board name.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Adding Spider board documentation based on Renesas official documentation
and following Zephyr guideline.
The documentation is describing the board and its current
Zephyr support.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Renesas Spider board use a S4 SoC (r8a779f0).
Add basic support for UART, GPIO and clock control.
We are using SCIF0 as SCIF3 is used by Linux.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
There are duplicated names specified in per-board YAML files.
This change will allow distinguishing boards in software that
presents the pretty names and not the raw names of boards.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Add Renode simulation support for `hifive_unmatched`, the
script is basically copied over from `hifive_unleashed`, with
very minor edits.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Make Jlink a default runner for lpcxpresso55Sxx.
The LinkServer runner command line tool does not support .hex flashing.
This feature is planned for LinkServer v1.6 (July 2024).
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
This patch changes readme files of nRF91x1 dev kits to highlight
their added NR+ feature.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Added modifications to support async apis for ns16550
on RPL-s using LPSS DMA.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
When playing with PM related applications, stm32cubeprogrammer is
useful to allow flashing even when SoC is in Stop mode.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
This is a follow-up to commit 7a83724e0f.
There is no reason to mark that many GPIO lines as reserved on this
board. And doing so causes several existing tests to fail as they
are configured to use some of those now unavailable GPIO lines.
Limit reservation to the lines that actually cannot be used as
GPIOs without changes in the default configuration of the board
or its physical modification (via solder bridges), i.e.:
- XL1 and XL2 (connections for the 32.768 kHz crystal)
- NFC1 and NFC2 (NFC antenna connections)
- RESET
- TXD and RXD (lines used by the console UART)
- QSPI lines: CS, CLK, and DIO0-3
Provide names for all the GPIO lines that are described on the board.
Even for the reserved ones, so that it is clear why they are reserved.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the WeAct Studio STM32G431 Core Board.
Tested with:
- `samples/basic/blinky`
- `samples/basic/button`
Flashed samples using dfu-util.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
This commit adds missing pinctrl configuration for USARTs in
efm32gg_slwstk6121a, efm32gg_stk3701a and efr32_radio boards
and enables PINCTRL for efr32_radio_brd4180a
and efr32_radio_brd4187c boards.
Signed-off-by: Franciszek Pindel <fpindel@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This commit moves configuration of hfxo from headers defined on board level
to device trees of SoCs.
Signed-off-by: Franciszek Zdobylak <fzdobylak@antmicro.com>
The title for this board README was very broken, messing up not only
this board's README but also the boards TOC.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This moves the k_* memory management functions from sys/ into
kernel/ includes, as there are kernel public APIs. The z_*
functions are further separated into the kernel internal
header directory.
Also made a quick change to doxygen to group sys_mem_* into
the OS Memory Management group so they will appear in doc.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
In some cases, the APPLICATION_BINARY_DIR does not match
the CMAKE_BINARY_DIR, in those cases the native simulator
build would not find the zephyr elf file.
Fix it by using the correct variable.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Instead of always enabling fuse for native_posix,
let's give users instructions on how to enable it
while building.
In the documentation: replace the references to native_posix
with native_sim, improve the links, mention the flash
simulator, and provide a separate subsection for FUSE access.
Add a separate test for the sample with fuse access enabled
and be sure it is possible to run both this and the basic
one with native_sim (was filtered out before for native_posix)
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Split the common keyboard scanning code out of the ITE specific driver
and use the generic code instead.
Note that this changes few timing defaults, the change is not
significant though so I suspect there's no difference in practice.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Polish and correct the documentation to reflect the use
of the native_simulator, and the fact that we have
now more than one bsim board in tree.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Update this board docs to reflect that these 2 peripherals
are now supported.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable LinkerServer and PyOCD runners for LPC55Sx6 EVKs,
where it is supported.
It was tested on a real HW.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Replace the references to native_posix with native_sim,
and update link names accordingly.
Background: during this release native_sim is replacing
native_posix as the main host test/development platform.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add configuration lines to be able to use the jlink debugger with this
board. The disco board leaves the debug lines tri-stated until connecting
to stlink, so it is safe to just plug in the jlink and use it.
Signed-off-by: David Brown <david.brown@linaro.org>
Add Verdin iMX8M Plus board with i.MX8MP SoC and ARM Cortex-M7 processor.
Add two targets (DDR and ITCM) for the iMX8M Plus board.
Port and documentation are based on NXP MIMX8MM EVK board.
This code is intented to be used with the Cortex-M7.
Signed-off-by: Gabriel Freitas <gabriel.freitas@toradex.com>
Currently, the NXP S32 SoCs have three redundant Kconfig hidden
options to define the part number. To streamline this, we will
retain `CONFIG_SOC_PART_NUMBER` to store the part number as a
string and `CONFIG_SOC_PART_NUMBER_<part>` that can be selected
by the boards.
Furthermore, for drivers requiring conditional code compilation
based on the target SoC, they should utilize the series or SoC
config option as applicable, instead of the part number config.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The existing S32K3 Kconfig options employ the `M7` suffix, which is
redundant given that all cores in this series utilize an Arm Cortex-M7
core. Therefore, we should remove it.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add Renesas rzt2m gpio driver with basic functionality.
It supports pin mode configuration and writing/reading to/from gpio ports.
Includes dts changes to build blinky sample.
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
This adds a new driver for Renesas RZ/T2M.
The driver allows configuration of pin direction,
pull up/down resistors, drive strength and slew rate,
and selection of function for a pin.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
This adds a UART driver for the Renesas RZ/T2M
Serial Communication Interface.
The driver implements:
* Polling API,
* Interrupt-driven API.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
This adds a new SoC: SOC_RENESAS_RZT2M
and a new board: rzt2m_startek_kit
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Co-authored-by: Roman Dobrodii <rdobrodii@antmicro.com>
Let's replace the references to native_posix with native_sim,
Background: during this release native_sim is replacing
native_posix as the main host test/development platform.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
During this release native_sim is replacing native_posix
as the main host test/development platform.
Therefore, instead of basing the native_sim documentation
in native_posix's one, let's do it the other way around.
This commit mostly moves documentation from the native_posix
page into the native_sim one, changing the board and renaming
labels.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Modify toctree glob to exclude common directory which keeps rst
helpers. This allows to include several boards documentation from the
common board directory.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add board definition for UP Squared Pro 7000.
The board is powered by Intel Alder Lake N (N-series Intel Platform).
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add support for low power mode on the G1120B0MIPI using the RT595. This
configuration is tested via a testcase in samples/drivers/display, which
should validate that the display can be driven by the RT595 when
CONFIG_PM and CONFIG_PM_DEVICE are set.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added a short paragraph explaining how to use pyOCD to flash and debug this
board, as well as a disclaimer requested by NXP
Signed-off-by: Tim Guite <tim.guite@ttp.com>
Enable the gpio0 node and mux the heartbeat LED. Moreover, add the
heartbeart LED as LED node and create an alias with 'led0'.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
- Make caparray delta a Kconfig variable
- Set caparray delta for beagle_bcf at beagleconnect_freedom_defconfig
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Convert the ITE keyboard scanning driver from kscan to input, add the
corresponding kscan compatibility node to the current board, build test
only.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Due to the west build path in official sample doc is now change
to root directory, we modify our west build command align the
official sample doc.
Signed-off-by: Kevin Wang <kevinwang821020@google.com>
Support NXP MRT on LPC55XXX SOC series, enable on
lpcxpresso55s69_cpu0, add test overlay to counter basic api test
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Read real frequncy from ARM Arch Timer instead of using define
'CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC' which can be incorrect for
some run cases. If we run xenvm under qemu we get one frequency, but
we can run this build as a DomU for Xen under different real platforms
and thus with differenty arch timer frequencies. So, we need to read
frequency from the timer registers.
Signed-off-by: Mykola Kvach <xakep.amatop@gmail.com>
This commit introduces all changes necessary for utilizing
the serial interface on i.MX8QM/QXP.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This commit enables clock control on the i.MX8QM and QXP boards.
This is achieved through the following changes:
1) The "reg" property is no longer marked as required
for the "nxp,imx-ccm" binding. This is necessary because
in the case of i.MX8QM and i.MX8QXP the clock management
is done through the SCFW, hence there's no need to access
CCM's MMIO space (not that you could anyways).
2) The DTS now contains a scu_mu node. This node refers
to the MU instance used by the DSP to communicate with
the SCFW.
3) The CCM driver needs to support the LPUART clocks
(which will be the only IP that's supported for now)
and needs to perform an initialization so that the
NXP HAL driver knows which MU to use to communicate
with the SCFW.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
As the name suggests, this commit attempts to cleanup some
of the configurations for the i.MX8 series. This cleanup
consists of either relocating the configuration or removing
unnecessary configurations.
As a rule of thumb, SoC-specific configurations have been moved
to Kconfig.series. If the configuration is by default 'y' and
needs to be set to 'n' or it has a numeric value then it has
been moved to Kconfig.defconfig.series. Configurations that
are default 'n' and were also explicitly set to 'n' have been
removed. Also, enabling logging has been moved to the board
level to avoid having to force all boards based on the same
SoC to enable logging.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This commit attempts to split the generic i.MX8 SoC into its
QXP and QM variants. As things are now, the i.MX8 SoC doesn't
have any NXP HAL files to back it up. As a consequence, the
native Zephyr drivers cannot be used.
To solve this issue, the generic i.MX8 has been split into
i.MX8QXP and i.MX8QM, each of them having different NXP HAL
files.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add drivers for gpio_i2c_switch which is present in beagleconnect freedom
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
Commit 944ced68f5 enabled
CONFIG_UART_CONSOLE=y for the beagleconnect_freedom board, which had the
side effect of satisfying a required dependency for the sensor shell
sample application and causing new build errors in the weekly full
twister run. Fix the build errors by moving the board's light and
humidity sensor nodes to be children of the I2C controller node.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
This board HW models do not yet support the NFCT peripheral,
let's remove the DT node to avoid the driver being selected.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This patch removes the now unused scratch partition and enlarges
the application slots instead.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
This commit enables clock control instances for apollo4p_blue_kxr_evb.
Also adds pin configuration for each instance.
Signed-off-by: Aaron Ye <aye@ambiq.com>
This is support for AArch64 development board.
The board uses 4-core Cortex-A55, which are based on
the ARMv8.2 architecture.
In addition,we support smp support and
it can use 4-cores to run basic samples.
Signed-off-by: Charlie Xiong <1981639884@qq.com>
Enable ticket spinlock on nsim SMP board as they are
naturally vulnerable to spinlock unfairness due to
SMP nSIM way of work.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Add in DT the possibility to configure both INT1 and INT2
pin. The driver will then assign one of the two (either 1
or 2, according to what value drdy_pin is set) to a gpio
for receiving drdy interrupts.
The other pin may be used in the future to receive event
interrupts.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Commit c6e3bac4f changed the core clock frequency of LPC55XXX series.
That clock is used by the cortex-m systick timer, which is the
default timer used for system time in zephyr on this series.
The bug is that the config SYS_CLOCK_HW_CYCLES_PER_SEC default was not
updated on the affected platforms to account for this change, so system
time is currently recorded as 150% of reality. Fix this by changing the
kconfig to be set automatically at SOC level and remove board defaults.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This chip uses an active low reset, so the correct behavior here is to
define the pin as ACTIVE_LOW, using GPIO_OUTPUT_ACTIVE to assert the
reset and set to 0 to deassert.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This chip uses an active low reset, so the correct behavior here is to
define the pin as ACTIVE_LOW, using GPIO_OUTPUT_ACTIVE to assert the
reset and set to 0 to deassert.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Basic spinlock implementation is based on single
atomic variable and doesn't guarantee locking fairness
across multiple CPUs. It's even possible that single CPU
will win the contention every time which will result
in a live-lock.
Ticket spinlocks provide a FIFO order of lock aquisition
which resolves such unfairness issue at the cost of slightly
increased memory footprint.
Signed-off-by: Alexander Razinkov <alexander.razinkov@syntacore.com>
The sfdp table property is no more required in the DTS of the
stm32h7b3i_dk as it is correctly read from the external
NOR octoflash with the read-sfdp command.
(since PR https://github.com/zephyrproject-rtos/zephyr/pull/62521)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the required conf and dts overlays required for the
application on stm32h747i-disco board.
Also moved CONFIG_SDMMC_STM32_HWFC option from prj_blk.conf to
nucleo_h743zi_blk.conf as that is STM specific option.
Build the application as
west build -p always -b stm32h747i_disco_m7 \
samples/subsys/fs/littlefs/ -- \
-DOVERLAY_CONFIG=boards/stm32h747i_disco_m7.conf -DCONF_FILE=prj_blk.conf
Signed-off-by: Murali Karicheri <murali.karicheri@sandc.com>
STM32L562 Discovery kit is not compatible with Bluetooth over USB
application.
Add missing information related to the BLE capability of this board.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Modify SPI configuration to match the features introduced in PR #63437.
Set the property "controller-data-delay-us" to zero for boards
which are using BlueNRG-MS.
Fix Chip Select configuration for stm32l562e_dk board.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Adds the device trees for the board and its Arduino connector,
default Kconfig and documentation.
The following features have been confirmed working on hardware:
* ADC
* I2C
* RTC
* SPI
* SDMMC
* UART
* OctoSPI Flash
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This makes intel_rpl board configuration similar to other Intel
boards (like intel_adl) and also fixes SHELL_STACK_SIZE configuration.
It should depend on ACPI.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
axp192 is used by the display controller and gpio hog subsys
thus we need to set this priority to the smaller value.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
The workqueue test may intermittently fail, with errors such as:
work_1cpu_test_1cpu_system_schedule: (elapsed_ms <= max_ms is false)
long 102 > 101
Disabling PM makes the issues go away, and it is what this patch does.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Instead of those set, use the default ones
for the MFD/REGULATOR_AXP192_INIT_PRIORITY/GPIO_AXP192_INIT_PRIORITY
that are set to the 80/86/81 values correctly. Adjust the
GPIO_HOGS_INIT_PRIORITY only to be executed after GPIO driver.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Fix MCUBoot error for LPC55S69 "slots are not compatible".
Use the standard slot naming,
used by TFM-enabled Zephyr platforms.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
The existing driver and sample:
- drivers/bluetooth/hci/rpmsg
- samples/bluetooth/hci_rpmsg
are no longer correctly named, since they now use the IPC subsystem to
send and receive data. The IPC subsystem can use RPMsg as a transport,
but that is one of several selectable backends.
I initially wanted to deprecated both the BT_RPMSG Kconfig option as
well as the zephyr,bt-hci-rpmsg-ipc chosen node in Devicetree. However,
this proved to be undoable in the case of the Kconfig option. This is
because it's a choice option, and those have special behavior. In
particular, the only practical way to deprecate would've been to keep
the old Kconfig option outside the choice (much like it's done in this
commit) but then also add a 'depends on !BT_RPMSG' on each of the
remaining choice symbols *except* on the new BT_HCI_IPC one. This, however,
only works correctly for .conf files. If a board instead sets the
default BT_HCI_BUS_TYPE in the Kconfig.defconfig file then the Kconfig
tree parsing would fail, because it'd try to set it to a value
(BT_RPMSG) that is no longer part of the choice.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Unify spelling of CAN Flexible Data-rate abbreviation to "CAN FD" instead
of "CAN-FD". The former aligns with the CAN in Automation (CiA)
recommendation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for the Arduino UNO R4 Minima.
This board is the newest version of Arduino that uses Renesas RA4M1 SoC.
This commit provides only limited support to simplify the initial
support patch.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
The PRT bus name for most (especially older) platforms is _SB.PCI0. Only
newer platforms use something else (like _SB.PC00).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ACPICA initialization takes considerably more than 32k. E.g. on
up_squared the utilization is 400-500k, qemu_x86_64 about 120k and on
EHL about 1.5M. Increase the default on these platforms to be big enough
if ACPI is enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
`cs-gpios = <&gpio1 23 0>;` is incorrect, since pin P1.23 does not even
exist in nRF52833. According to schematic, it should be P0.23 and this
CS line should be configured as active low.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Serpente schematic has the same clocking arrangement as
boards/arm/adafruit_trinket_m0. This fix copies the clocking
config from the trinket.
Fixes https://github.com/zephyrproject-rtos/zephyr/issues/64470
Signed-off-by: Tom Keddie <github@bronwenandtom.com>
In the documentation recently started to appear ':orphan:', which is
marking for orphaned page. Use start-after to include after marking.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Enable using a BlackMagicProbe for flashing and debugging XIAO BLE
boards.
Tested successfully with BMP 1.9.2 running on ST-Link/v2 against a
`xiao_ble` board.
Signed-off-by: Augusto Zanellato <augusto.zanellato@gmail.com>
Add support for these two options in the simulated board.
Before these options were otherwise defined in the real
BOARD/SOC kconfig files, which meant samples/tests which
used them would not be able to build due to a kconfig error.
With this change they can both be selected, and the right
functionality is built in.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The header file defines macros that are not used in the boards dts but on
the SoC level. They should be include where they are used.
Signed-off-by: Franciszek Zdobylak <fzdobylak@antmicro.com>
