This commit implement the UART asynchronous API mode support.
When the API is used, the UART hardware cooperates with the DMA (MDMA)
module to handle the the data transfer and receiving.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
This enabled extended sleep for Renesas SmartBond(tm).
Extended sleep is low power mode where ARM core is powered off and can
be woken up by PDC. This is default sleep mode when CONFIG_PM is
enabled.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Squash the two copies of this file found in `dts/arm` and `dts/arm64`.
Their contents were identical up to devicetree property ordering.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
This file was moved to the `dts/arm64` directory 3 years ago:
3539c2fbb3
However, the original file in `dts/arm` was left by mistake. Since then,
it's been unused and seldom updated, but it hasn't diverged much.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
This file is basically a copy of the AM62x M4 dtsi but an
additional mcu_uart1 interface.
The internal clock frequency feeded into the UART IP is
96 MHz instead of 48 MHz, which is different to the AM62x.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
We define two frequencies in the am62x_m4.dtsi file.
Use DT_FREQ_M for both frequency to make them more
human-readable and easier to understand.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
This implements basic driver to utilize the I3C IP block
on NPCX.
1. I3C mode: Main controller mode only.
2. Transfer: Support SDR only.
3. IBI: Support Hot-Join, IBI(MDB).
Controller request is not supported.
4. Support 3 I3C modules:
I3C1(3.3V), I3C2(1.8V, espi mode), (I3C3 1.8V or 3.3V)
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
Updated dts for MCXN94x with support for CTimer.
Signed-off-by: William Tang <william.tang@nxp.com>
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
FTM internal counter can be clocked by one of three clock sources
independent of the module bus clock. This patch introduces a DT property
to perform the clock selection from DT.
DT sources are updated to keep the current clock selection for all boards,
with exception of ucans32k1sic board which is migrated to use system
clock by default, as this seems to be a better choice for most cases.
Some PWM LED samples require slower clock so overlays are added for
those cases.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Set RTC clock source to the internal 32 KHz LPO. Currently RTC clock is
used to source RTC counter and FTM counter.
Fixes#71289
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Convert all of the NXP SOCs with ENET to use the new
binding scheme, which is used by the new driver.
Convert any boards using this SOC to the new scheme as well,
and remove from the documentation the bit about the experimental
nature of the new driver and the overlay that shall no longer exist.
Some of the boards I do not have the hardware of, so apologies
if something breaks, as I have no way to know. All the boards
were made sure to at least build.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add a VEVIF node to be used for communicating with SysCtrl (cpusys).
This is the only part of the SysCtrl VPR exposed to local domains.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
This commit updates the SRAM configuration in the STM32L475 device tree:
- `sram0` size reduced from 128K to 96K.
- `sram1` added with 32K.
These changes correct memory settings to prevent initialization failures.
Signed-off-by: Tianshuang Ke <qinyun575@gmail.com>
Nuvoton NPCX chips have reset registers which allow to reset the
peripheral hardware modules. This commit adds the support by
implementing the reset driver. Note that only the reset_line_toggle API
is supported because of the nature of the reset controller's design.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Copy the DMA channel information to both UART and SPI
instances of the Flexcomm as only one of them can be
active.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
CSS was deprecated from the mcu-sdk. Removing driver from lpc55s36
to clear build error.
This is a temporary patch to remove the build error.
Fixes#69961
Signed-off-by: David Leach <david.leach@nxp.com>
Add definitions of PWM peripheral instances so it can be utilized
on nRF54H20 and nRF54L15 devices.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add EDMA channels for LPUART RX and TX to LPFLEXCOMM 2 and 4, as these
nodes are enabled with the UART driver
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable sleep mode on LPC55S69 (corresponding to zephyr's runtime idle
mode). Add DT description and power api implementations.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add common gpio node to pinctrl node (interrupts are shared between ports)
and syscon for interrupt edge detection register in order to support
interrupts in rzt2m gpio
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
