Unify spelling of CAN Flexible Data-rate abbreviation to "CAN FD" instead
of "CAN-FD". The former aligns with the CAN in Automation (CiA)
recommendation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Power rails of some peripherals are controlled externally.
This is a case in embedded controllers, where the power of
some I2C devices are managed by the main application
processor.
To ensure that zephyr drivers access the devices where is
powered on, introduce a "monitoring" power domain. It works
by registering interrupt handler with gpio a pin, so that
when power state changes, it will notify relevant drivers.
Additionaly add CONFIG_POWER_DOMAIN_INIT_PRIORITY to replace
harcoded init priority.
Fixes: #51349
Signed-off-by: Albert Jakieła <jakiela@google.com>
Adding initial support for Renesas RA UART.
To avoid complicating initial code for supporting the SoC,
I have implemented only the bare minimum for now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add initial support for Renesas RA GPIO.
To avoid complicating the initial code for supporting the SoC,
I have implemented only the bare minimum for now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
To avoid complicating the initial code for supporting the SoC,
I have implemented only the bare minimum for now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
To avoid complicating the initial code for supporting the SoC,
I have implemented only the bare minimum for now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add initial support for Renesas RA clock generation circuit.
It returns a fixed value to simplify the first commit to get the UART
working now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
In the CONFIG_SPI_NOR_SFDP_MINIMAL configuration this value is hard
coded to 256 bytes. Make it configurable via devicetree.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
We currently have three keyboard scanning drivers in the code base
(npcx, it8xxx2 and mchp_xec, last two yet to be converted to input).
These have been largely copy pasted from each other and share a lot of
the same structure and code.
This PR lays a foundation to start decoupling feature from those drivers
into a common code base, and it is heavily inspired by the current
regulator common data/config one.
Feature wise this only moves the thread struct, stack and initialization
to the common code and declares the thread callback as the only API, but
the intent is to move as much code as possible in there an only abstract
device specific callbacks in the api structures.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This commit adds a GNSS driver for the Quectel LCX6G
series of GNSS modems (LC26G, LC76G, LC86G). It is
based on the modem subsystem, and the GNSS utilities
added in the two previous commits.
Signed-off-by: Bjarki Arge Andreasen <bjarkix123@gmail.com>
The default is that the high time for open-drain clk is one
PPBAUD, which is typically very short. Some device require
a longer high time during the open-drain address phase so
add a property to allow device tree to override the default.
Signed-off-by: Mike J. Chen <mjchen@google.com>
The labels used in chosen node are not defined in dtsi file.
They are defined on board level and also chosen is already set there to
proper values.
Signed-off-by: Franciszek Zdobylak <fzdobylak@antmicro.com>
The header file defines macros that are not used in the boards dts but on
the SoC level. They should be include where they are used.
Signed-off-by: Franciszek Zdobylak <fzdobylak@antmicro.com>
for nucleo_stm32g0b1 board.
the HSI48 clock is the clock used by default for the USB controller,
however its default tolerance is not enough for the USB specification,
leading to some random errors depending on many factors, including the
upstream HUB or host.
this commit adds an option in the device tree to enable the STM32 Clock
recovery system (CRS) using USB SOF packet reception as a reference,
which brings the HSI48 within the required accuracy for USB transfers.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
Refactor the pinctrl nodes slightly so that the port devices are not
child of the main pinctrl node. This is because the pinctrl node is
being used as parent for pinctrl setting nodes itself, and having the
port nodes as child end up creating a circular depdency with the edt
child enumeration patch.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Refactor the pinctrl nodes slightly so that the port devices are not
child of the main pinctrl node. This is because the pinctrl node is
being used as parent for pinctrl setting nodes itself, and having the
port nodes as child end up creating a circular depdency with the edt
child enumeration patch.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Modified files (yaml, dts, overlay, and c) which were using spi-cpol
and spi-cpha to be compatible with the new structure.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Add support to set SPI clock polarity (CPOL), clock phase (CPHA), and
hold-on-cs in a dts file to get rid of using related macros in spi.c driver
since each board may work on a different SPI mode rather than the default
one (based on CPOL and CPHA).
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
This commit adds basic support for m5stacks M-Bus extenions port that is
support my core and core2 module.
Signed-off-by: Martin Kiepfer <m.kiepfer@teleschirm.org>
Allows device tree to enable usage of the controller feature
where HS clock is disabled when not in use, which is good
for reducing power consumption if MIPI DSI is mostly idle.
Signed-off-by: Mike J. Chen <mjchen@google.com>
The BCM2711 SoC exposes 58 GPIOs. The first 28 (bank 0) are accessible
to users via the 40-pin header, while the others (bank 1) are used for
controlling on-board peripherals.
This also update doc of `rpi_4b` board.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
No reason to declare it per node, as it is almostly shared by all
peripherals.
Also introduced `DT_FREQ_M` macro for better readability.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
This files has been changed as part of a refactoring in 13a87081b9.
Unfortunately the refactoring introduced few issues:
- usage of devicetree macros before their definition
- usage of pinctrl label before the definition of the corresponding node
- removal of few node overrides that are causing build errors
Unfortunately there's no board usptream using this specific dts file, so
the issue has not been caught in CI and was only found downstream.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This commit adds the RTC device to the following
atmel sam devicetrees:
- sam3x.dtsi
- sam4e.dtsi
- sam4s.dtsi
- same70.dtsi
Signed-off-by: Bjarki Arge Andreasen <bjarkix123@gmail.com>
Enable driver for intel lw uart.
Changes from review:
- refactor spinlock to inside of loop
- use menuconfig for kconfig
- add CONFIG_UART_INTEL_LW_AUTO_LINE_CTRL_POLL
Signed-off-by: Teoh Shi Lin <shi.lin.teoh@intel.com>
add basic sensor support for 3-axis accelerometer, currently
this driver support data acquisition and motion detection
features.
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
HAS_DTS has become a redundant option. All Zephyr architectures now
select this option, meaning devicetree has become a de-facto
requirement. In fact, if any board does not provide a devicetree
source, the build system uses an empty stub, meaning the devicetree
machinery always runs.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
STM32WB MCUs has two AES peripeherals. Add AES1 definition, AES2 must not
be used by application CPU core.
Signed-off-by: Lukasz Hawrylko <lukasz@hawrylko.pl>
Add wakeup_duration support. (WAKE_DUR in WAKE_UP_DUR)
Value is configurable through DT per instance.
Signed-off-by: Adrian Wojak <adrian.wojak@outlook.com>
Use a new property, "clock-mux" to select the clock mux for the SAI.
Previously, the clock mux was being selected using the "bits" specifier
of the "clocks" phandle property, which is not the purpose of this
specifier. This can be shown by the regression introduced by 5bebbb91,
which changed the "bits" field to the clock gate shift (which is the
intended meaning).
This incidently worked for the SAI1 and SAI3 peripherals, as the lower 2
bits of the correct clock source selection (0b10) are the same as the new
value placed in the "bit" specifier. For SAI2, the clock source was
switched to PLL3 PDF0 by this change.
To resolve this, use an explict "clock-mux" property for this selection.
Fixes#63541
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a new SPI shim driver for Intel SoCs. Builds upon the SEDI bare
metal SPI driver in the hal-intel module.
Co-Authored-By: Kong Li <li.kong@intel.com>
Signed-off-by: Ye Weize <weize.ye@intel.com>
Adds a devicetree for describing common battery characteristics used
by multiple devices and subsystems.
Signed-off-by: Ricardo Rivera-Matos <ricardo.rivera-matos@cirrus.com>
MEC172X series SoCs share most IP but the -LJ series expands the PWM and
ADC channels available as well as defines extra pinctrl pins.
Separating these better to be able to simplify their inclusion and
driver code. Any board based on either the -SZ or -LJ package can just
include the mec172x<sz/lj> dtsi files for their specific package.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
This commits adds the DA14695 variant.
The main difference with the DA14699 is a smaller package with less
GPIO.
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
This is needed since commit f66b73197d
("drivers: hwspinlock: implement sqn hwspinlock driver") started
using it. Not sure how this got past CI.
Signed-off-by: Martí Bolívar <mbolivar@amperecomputing.com>
- if we have input enable use CY_GPIO_DM_xxxx else
CY_GPIO_DM_xxx_IN_OFF;
- added bias_high_impedance option
- Updated HIGHZ drive mode, now it sets if:
--- we have bias_high_impedance
--- or if input_enable and no addition bias mode
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Define WKPU interrupt controller node and its respective interrupt
sources mapping to GPIO pins.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Extend the NXP S32 GPIO driver to be able to route external interrupts
to either SIUL2 EIRQ interrupt controller or, when available on the
SoC, WKPU interrupt controller.
Since WKPU can support up to 64 external interrupt sources and SIUL2
EIRQ up to 32, gpio_get_pending_int() is removed and the interrupt
controller specific API must be used instead.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Introduce an interrupt controller for the NXP S32 WKPU peripheral
that can be integrated with GPIO to trigger interrupts through
external interrupt pad inputs.
WKPU can trigger interrupts from certain input pads that support this
function, as well as wake-up events to the power management domain. This
patch only adds WKPU functionality as an interrupt controller to extend
the number of input pads that can interrupt the core. Power management
functionalities are not supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The example sets the power-role to "SINK", but the value is
case-sensitive and only accepts lowercase "sink".
Signed-off-by: Jonas Otto <jonas@jonasotto.com>
Specify only the bus corresponding to the current yaml file, as done in
the adi,adxl372-spi.yaml.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
The PCA9633 i2c LED controller offers an All Call address in its nominal
operation, allowing simultaneous communication with all instances present
on the same i2c bus. The default address is 0x70. While this functionality
is convenient, it is possible that the board uses another i2c component
that also uses this address (for example, the shtcx). In such cases, the
address conflict prevents the proper functioning of the system.
The idea is to add a "disable-allcall" property to the device tree. If this
option is present, the initialization of the PCA9633 forces the bit 0
(ALLCALL) to be set to false, thereby disabling this function. It is
necessary to add this property to all PCA9633 devices on the bus to free up
the address 0x70.
Signed-off-by: Steve Jacot-Guillarmod <steve@piziwate.net>
Increase the `ndev` of PLIC to the max of 1024 from 53, as
supported by the RISCV PLIC. The total number of IRQs is now
1035(1024 + 11), up from 64(53 + 11).
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
The pre-alloacted size of the buffer for the SHA ROM API code increases
in npcx4 chip. This commit adds a new property context-buffer-size to
sha0 DT node in npcx9 and npcx4 separately. The driver can pre-allocate
buffer with the correct size based on the property.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Different nRF52 devices have different maximum TWI DMA transfer size,
and it's easy to hit the limit with i2c displays on nrf52832 (8 bit) and
nrf52810 (10 bit). Currently neither the driver or the hal validate the
limit, leading to random NACK errors when trying to transfer more data.
Add a check on the driver to fail gracefully when going over the limit.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
These two have been converted from kscan to input already, move the
bindings over to match the change.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Reword the descriptions for the bus-speed, sample-point, bus-speed-data,
and sample-point-data CAN controller devicetree properties.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Define all the register offset directly in the driver according
to the RISCV PLIC specification as they are not configurable,
see: https://github.com/riscv/riscv-plic-spec.
Updated devicetrees that has PLIC accordingly.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Removing the edge-trigger Kconfig as it is supported by default
in the RISCV PLIC specifications.
Define the edge-trigger register offset in the driver instead
of retrieving the value from devicetree as it is not something
configurable. The value 0x1080 is defined in Andes & Telink
datasheets.
Updated build_all testcase.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Added pinctrl nodes for Silabs SoCs where they were missing:
efm32pg, efm32hg, efm32wg, efr32mg21.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
This continue PR #31270. The updated changes are:
- Updated to work with latest zephyr
- Inplace reads/writes of registers
- Batch read of RX messages when multiple messages can be read
- FIFO abstraction of RX/TEF queues
- Handle ivmif errors
- Use READ_CRC for register reads
- Use bitmasks instead of bitfield members
- Rename mcp25xxfd to mcp251xfd
- General cleanups
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Use clock control API to retrieve the counter module's frequency and
update the boards using it to provide the source clocks.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
add host controller driver support for emmc version 5.1.
The driver expose zephyr sdhc api interface for emmc host controller.
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
This introduces pwm capture shim driver for NXP S32 EMIOS,
the driver uses SAIC mode that is supported for all channels,
to capture the counter value on each edge for period/pulse
measurement
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This prepares support pwm capture APIs by extended current pwm
shim driver but use a differrence hal component:
- Introduce a Kconfig options that will be set when PWM pulse
generation API is used, it is also used to select the hal
component. Guarding current code inside this Kconfig option
- Increase #pwm-cells to 3, flags is supported for PWM capture
- Do not require duty-cycle and polarity be set in dt, PWM
capture doesn't need it.
- Rename emum value for pwm-mode to keep only key information
- Add preprocessor in case no channel is configured for generate
PWM output, to avoid warning when build
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This enables and declares interrupt handlers for eMIOS,
the handlers defined and implemented at HAL, the driver
takes the name for each id from interrupt-names devicetree
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Add "st,stm32-flash-controller" as compatible for STM32H7 so that
what is defined for STM32 in general is also defined for STM32H7.
Already most of the other STM32 versions have this addition.
Also removed the specific STM32H7 flag check in
/flash/driver/Kconfig.stm32.
Signed-off-by: Stefan Petersen <spe@ciellt.se>
Updates Ethernet PHY devicetree bindings to be more consistent with
Linux by using the standard `reg` property for the PHY address instead
of a custom `address` property. As a result, MDIO controller bindings
now require standard `#address-cells` and `#size-cells` properties.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Some Ethernet PHYs used the devicetree node name `phy`, while others
used `ethernet-phy`. Be consistent and use `ethernet-phy` throughout.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Provide the soc configuration for sdmmc1 and sdmmc2 controllers.
This includes registers address, clocks, resets and interrupt line
details.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
