Document offloaded sockets driver, which is an alternative to Ethernet
driver for networking applications.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Co-authored-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Use NSI_HW_EVENT() in order to periodically check for events in host
sockets. Whenever there is a socket event ready to be processed by Zephyr,
raise native_sim (newly introduced) CPU interrupt, so that Zephyr driver
can signal readiness with k_poll().
Maintain a list of Zephyr poll() executions in Zephyr context. Iterate
through them whenever there is some event to be processed.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
regression.sh path is now tfm/api_ns/regression.sh, reflect it in the
doc.
Remove duplicate TF-M material.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Rather than providing flash partitions in samples, provide default
partition (no tests) as part of the board ns variant default configuration.
Update or remove related overlays.
Update ns variant yaml file to specify actual flash available for the
ns application (36K).
Additionaly, fix comment in b_u585i_iot02a_ns.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Clean up early days TF-M development directives which are outdated today.
Factorize remaining CMake instructions in soc.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Removes instances of setting CONFIG_BOARD that should have been
removed in the hwmv2 porting process
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Replaces inaccurate or wrong vendor prefixes in board and soc
folder names with those from thr vendor prefix file
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds the user-provided board qualifiers to Kconfig so it can be
used by application code, along with one containing the full string
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Followup: #69905
Adopting new board terminology for CMake, python, and Kconfig code to
use qualifiers instead of identifiers.
Also adjusted to board target where applicable.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Move the Kconfig symbols SOC_ESP32_PROCPU, SOC_ESP32_APPCPU,
SOC_ESP32S3_PROCPU, and SOC_ESP32S3_APPCPU.
The CPU cluster is defined in espessifc/soc.yml and should therefore
be available in the HWMv2 Kconfig.soc tree.
This will allow sysbuild to test for the CPU cluster when targeting
remote board for a build.
Update espressif boards accordingly.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The GRTC channels and irqs configuration for Radio domain
is SOC specific not board specific. Move the configuration
to SOC dtsi file.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Replace the uses of the hwmv1 names in the board documentation
with the corresponding hwmv2 ones.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Remove the hwmv1 twister board definitions for the
nrf5340_bsim targets in preparation to
transition to the new definitions for hwmv2
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The child-owned-channels property of GRTC is used by nrfx_grtc
driver to exclude channels for common pool of channels allowed
for dynamic allocation. That is sort-of workaround for missing
property that allowes to remove some channels from the pool.
There are also not aligned GRTC IRQs for nRF54H20 and nRF54L15.
Only one of avaialbe IRQs was added to GRTC in DTS whereas
there should be two. That allows to find second IRQ by other
drivers that use GRTC peripehral.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Enable CTimer0 and MRT0 channel 0 by default on the board,
and add more of the device instances in the counter api test overlay.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The led-strip alias can be determined in the base dts file.
Remove from overlay files and aggregate to the base dts file.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Removing `choice WS2812_STRIP_DRIVER` to enable the use of multiple
types of WS2812 drivers.
Also, `menuconfig WS2812_STRIP` will be deleted as it does not
correspond to the appropriate settings.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Enable support for the mx25u51245g flash chip present on the
RD RW612 BGA. Support has been verified with the following samples:
- samples/drivers/flash_shell
- tests/drivers/flash/common
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
CAN requires 120 ohm termination at both ends of the bus, resulting in a
bus impedance of 60 ohm. Fix the board documentation to reflect this.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This board fails to build for a multitude of samples & tests
which is blocking CI.
Let's provisionally disable it until the matter is properly
resolved.
The issue was introduced with the NXP HAL update to 2.15:
e4e463af81
See https://github.com/zephyrproject-rtos/zephyr/issues/69961
for more information.
Once this issue is fixed, this change should be reverted.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The native_sim boards support the DMA emulator just like
native_posix. The tag was just never added in the native_sim
twister yaml. Let's add it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
In practice, PPR is intended to be running code from RAM, so make this
the default choice for the `nrf54h20dk/nrf54h20/cpuppr` board target.
Keep the MRAM execution option as a `xip` variant of that target,
replacing the `ram` one.
Align the default `cpuapp` configuration for copying PPR's image to RAM
before it boots the child processor.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
nRF54H20 PDK is superseded by nRF54H20 DK and will no longer be
supported.
The board was superseded by nRF54H20 DK.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add targets for the Application, Radio, and PPR cores in the nRF54H20
SoC on the nRF54H20 DK board.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable support for dma controller on RD RW612 BGA board, and add overlay
to enable board in dma loop transfer test
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Ignore userspace tag completely. Disabling USERSPACE in board kconfig is
not right, this will always be overidden by the application and we will
have build failures. The HW supports userspace and most filters in tests
depend on this capability.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Broadcom boards live in /boards/brcm, not /boards/broadcom
This commit fixes bad links accordingly.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Wurth Electronik boards live in /boards/we, not /boards/wurth_elektronik
This commit fixes bad links accordingly.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
U-Blox boards live in /boards/u-blox, not /boards/ublox
This commit fixes bad links accordingly.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Aconno doesn't seem to be around anymore. Remove deadlink to product page.
Issue originally reported in #67099
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This board's docs are now to be found on Qorvo website, update links
accordingly.
Originally reported in #67099.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Updated 3 dead (404) links in the doc page for Arduino Nicla Sense ME.
Also uniformized indenting of sphinx links in the process.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Move the GPIO button dts nodes to the common dts file so it
be selected by either cpu core.
Also fix an error in the GPIO setting for one of the switches.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Update lpcxpresso55s69_cpu0 (and ns target) names in build commands in
the board documentation. Also, correct the documentation for dual core
images on this part, as it was out of date.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix board identifier in overlays for the lpcxpresso55s69_cpu0 target.
Board identifiers were renamed with the following command:
for file in $(find . -name "lpcxpresso55s69_cpu0.*"); do;
mv $file ${file/_cpu0/_lpc55s69_cpu0};
done
Additionally, remove lpcxpresso55s69_ns overlay targets where they are
no longer needed (or rename them where they are)
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Using Zephyr SDK 0.16.5, openocd can be used to debug WBA based boards.
Fix documentation and clean up board.cmake configuration for
nucleo_wba52cg from a local configuration which shouldn't have been
upstreamed
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Which will replace the old native_sim_64 to align it with
the hwmv2 naming conventions.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Which will replace the old native_sim_64 to align it with
the hwmv2 naming conventions.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Replace uses of native_[posix,sim]_64 in the documentation
and kconfig help messages with native_[posix,sim]/native/64
to match the hwmv2 naming.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Remove the hwmv1 twister board definitions for
native_posix_64 / native_sim_64 in preparation to
transition to the new definitions for hwmv2
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This board's twister yaml file claims to support the
arduino-serial tests, but it does not provide
the necessary DTS node, which is causing
failures in CI.
Let's remove the tag from the twister board definition.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commit changes the value of the `arch` from `riscv64` to `riscv`, so
that it is in line with the rest of the RISC-V boards.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Due to number of IRQs the ROM offset, that contains MCUboot,
needs to be moved to address that is aligned with 2048 byte
long vector table.
This comes from Cortex-M requirement where vector table needs
to be placed at offset equal to lowest power of two number
that will fit vector table.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Signed-off-by: Mateusz Michalek <mateusz.michalek@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
RD RW612 BGA board is built targeting secure mode execution. If
CONFIG_TRUSTED_EXECUTION_SECURE is not set, base address declarations in
CMSIS header files will be incorrect, causing a variety of issues. Fix
this.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
these list of patches add support the Starfive Visionfive2
SBC based on the JH7110 SoC. Board identifier is `visionfive2`.
Signed-off-by: Kanak Shilledar <kanakshilledar111@protonmail.com>
Signed-off-by: Pratik Farkase <pratik.farkase@wsisweden.com>
Default pyocd configuration doesn't allow debugging on this board.
Now that Zephyr openocd version support stm32g0 series, use it instead
of pyocd.
This commit provides working openocd configuration for this board
an update documentation.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Add parentheses missing around $BOARD_REVISION.
The syntax without parentheses has been deprecated for at least 5 years:
https://github.com/ulfalizer/Kconfiglib/commit/374f48873424f9
That same documentation states "Using the old syntax with an undefined
environment variable keeps the string as is." This what actually happens
on Windows where `build/zephyr/.config` looks like this:
CONFIG_BOARD_REVISION="$BOARD_REVISION"
I found this because the behavior differs on Linux where the same,
"old" syntax produces this instead:
CONFIG_BOARD_REVISION=""
This could be because environment variables work differently?
(BOARD_REVISION is passed from kconfig.cmake to kconfiglib.py thanks to
cmake -E env)
Let's not try to debug this and just drop the deprecated syntax. It
aligns both Windows and Linux on the same, expected, empty string
behavior.
Note these are the only two `def_string` found across all Kconfig files
right now.
Fixes commit c11b7852d1 ("Kconfig: add CONFIG_BOARD_REVISION")
Fixes commit e2ff2a88ba ("sysbuild: include HWMv2 Kconfig in sysbuild")
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Split the common keyboard scanning code out of the XEC specific driver
and use the generic code instead.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the XEC keyboard scanning driver from kscan to input, add the
corresponding kscan compatibility node to the current board, build test
only.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
pinmux.c is inaptly named since it has nothing to do with pinmux.
Also, remove inclusion of iocon.h since this file does not use it,
as this file has nothing to do with pinmux.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add 'west flash' support which in the case of native_sim just start the
built application.
Reuse existing runner and rename it to be more generic as it does more
than just debugging now.
Also add debugserver command.
Fixes#36706
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
240MHz as APB1 bus clock is too fast to set I2C base bus speed.
Set bus pre-scaler to 2 and reach a safe 120MHz.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Enable i2c1 on stm32h573i_dk (arduino_i2c).
Additionally provide a test configuration for i2c_target_api.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
240MHz as APB1 bus clock is too fast to set I2C base bus speed.
Set bus pre-scaler to 2 and reach a safe 120MHz.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Enable i2c1 on nucleo_h563zi (arduino_i2c).
Additionally provide a test configuration for i2c_target_api.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Fix TF-M support for lpcxpresso55s69 target. The following issues were
resolved:
- lpcxpresso55s69 ns defconfig did not explicitly disable
CONFIG_TRUSTED_EXECUTION_SECURE (which is set in the secure cpu0
defconfig file)
- CONFIG_TFM_BOARD was not being set correctly for the NS target
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Mark counter as supported for nRF54L15 to allow running
counter_basic_api by twister.
Signed-off-by: Magdalena Pastula <magdalena.pastula@nordicsemi.no>
This commit enables the IRQSTEER interrupt controller
on NXP's XTENSA-based i.MX8QM and i.MX8QXP.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Adds i2c3 on the dts of nucleo_f401re.
Adds necessary overlay and nucleo_f401re in i2c_target_api test case
to enable the board.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
cpuapp/cpurad can be debugged using the J-Link runner.
Note:
This feature is still experimental and has known issues. For example,
setting a breakpoint to main requires to patch init.c with a loop
polling a variable so that we stop there until unset from GDB.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add Open Alliance spi protocol support.
Open Alliance is a chunk-based SPI protocol, based on sending
over SPI an ethernet frame divided in smaller chunks, using a
specific 32-bit header for each chunk transferred. All chunks
can be sent or received by a single dma transfer.
Default mode is set to Open Alliance SPI without protection,
since the adin2111 dev. board comes shipped this way.
Tested:
- Open Alliance SPI, no protection (default board shipped)
- Open Alliance SPI, protection
- Generic SPI, no crc
- Generic SPI, with crc8
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Nordic Semiconductor no longer offers support for this board, so warn
users to avoid it for new prototypes.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
In order to avoid defining almost the same overlays for different
sample codes and/or applications a common overlay file per
display interface is defined under the boards dts folder.
In doing so, an application/sample code will only have to
define another overlay explicitly under application's board
folder if more blocks are to be enabled. In either case, users
should explicitly invoke the requested overfiles at 'west build'
invokation by using the DTC_OVERLAY_FILE system variable.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Add build_only for the st,stm32-ethernet driver to the build_all
ethernet tests and add an entry for ethernet support to make sure
ethernet driver is built.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Enabled the PIT and Multi channel support
for some of the rtXXXX devices.
- rt1010
- rt1060
- rt1160
- rt1170
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Add `pico_serial` which is alias of `uart0` as a definition
related to pico_header.
The uart0(GP0 and GP1) is shown as default serial port
in pinout diaglam.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
For sharing pin definition property with `worldsemi,ws2812-gpio`,
rename `output-pin` to `gpios`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
This commit fixes#67277 and hence adds possibility
to properly utilize grove extension port.
5V_BUS can be enabled via regulator bus_5v. By default this
regulator is disabled.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
boards/espressif/esp32s3_devkitm/esp32s3_devkitm_esp32s3_procpu_.yaml
has needless `_` in filename.
Renamed it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Update board's DTS configurations to support the Renesas MIPI DBI
host controller.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Re-assign peripherals' default pins functionality to avoid
conflicts with LCD controller's pins usage. The PRO DevKit
exhibits a display socket which is routed to dedicated pins.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
This adds the minimal get_time/set_time support for the rp2040 and
enables support by default on the Pico boards. This doesn't support
configuring the clock source or alarm interrupts yet.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
pty is not available on Windows hosts. Running a sample in Qemu
on Windows shows an error. Fix it by enabling pty on Unix hosts only.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Add `zephyr,ipc-icmsg*` nodes, with mboxes specified in a common file.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Gerard Marull-Partetas <gerard@teslabs.com>
Add IPC shared memory regions in the global RAM, as well as an enlarged
SRAM region for Application core.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Set status = "okay" for temp device tree node to allow use
of nRF 802.15.4 Radio Driver on the nrf54l15pdk_nrf54l15_cpuapp board.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Set status = "okay" for ieee802154 device tree node to allow use
of ieee802154 on the nrf54l15pdk_nrf54l15_cpuapp board.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
fix QSPI NOR flash is25wp064a input page programming to 32h
as 38h isn't functional. Also adjust the frequency to max
possible value from nRF52 as 32MHz as the flash supports upto
133MHz.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Add CMake code that fixes west attach on nrf54l15pdk_nrf54l15.
I don't know why this fixes west attach as this is cargo cult code.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Generate `boards/deprecated.cmake` entries to map all legacy boards to
their HWMv2 incarnations.
Single-SoC, single-CPU boards, whose names haven't changed, don't need
to be listed here. In those cases, `BOARD=<name>` counts as a shortened
form of `BOARD=<name>/<soc>`.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Emulate SERIAL_SUPPORT_INTERRUPT for UART_NATIVE_TTY, using a thread that
polls the tty and invokes the callback.
This allows interrupt-driven subsystems such as modbus to use a native tty,
which is useful for testing purposes.
Signed-off-by: Björn Stenberg <bjorn@haxx.se>
The amount of RAM owned by PPR core is quite limited, making it
difficult to fit many samples. Instead, use execution in place and
increase its code partition from 28K to 64K (as now it doesn't have to
match RAM size).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This is a setting that depends on the board or application, so it should
not be part of SoC definition files.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Since bd9836be8c
the native logger is enabled always (even if a UART is present)
as it was though more conveniant for users.
But the documentation was not updated to reflect this.
Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The UP Squared board comes with different CPUs where Atom ones
run at 1.6GHz while the Pentium and Celeron ones run at 1.1GHz.
Since the APIC TSC Deadline timer driver is tied to the CPU
speed, and we were using 1.6GHz as the hardware clock speed,
real world time would not be correct for Pentium and Celeron
based boards (i.e. 1 second sleep requested in application does
not translate to 1 second in real world). Change it to use HPET
timer instead as HPET has the same clock rate for all board
variants. Applications requiring more precise clock rate can
override this in their configuration.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Support of stm32h5 targets with pyocd is required to allow debugging.
Provide runner configuration and update board documentation.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Commit 940c66f82e added a bunch of
ACPI PNP ID to x86 boards but skipped those for ACRN. And commit
34a2fbfba1 changed the behavior of
PCIe controller to looking for PNP ID, it results in compilation
error due to build asserts. So add the PCIe controller node to
the ACRN base DTS file.
Fixes#68956
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The nRF54* SoCs are in a very early stage of production and the software
supporting them is to be considered experimental. Document this
accordingly in the respective boards.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
If slots partitions are defined, related chosen should be configured.
Fixes build issue in samples/subsys/usb/dfu
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Prevent overrunning the irq vector table.
This is not happening today in tree, but coverity thinks it
may. Checking for it to prevent it is not a bad idea
anyhow, so let's do it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
i2c pads were incorrectly configured and failed to work when testing
against an external fram part. Correct the i2c pinctrl settings for
arduino i2c to match other boards in the mimxrt lineup.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Change reset pin polarity for MIPI DBI SPI controller, so that the board
devicetree is responsible for setting the GPIO to active low, and the
driver always sets the pin to a logic 1 to reset the display.
Fixes#68562
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The yaml uses `arch: riscv` while other boards specify either
`arch: riscv32` or `riscv64`.
Unify this by changing the value to `riscv32`.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Previously the boot_write_img_confirmed() function used the MCUboot
public API function boot_set_confirmed(), but this function is hardcoded
to set the confirmed flag of slot 0. This works for MCUboot swap modes
but not for Direct XIP, where applications can execute out of secondary
slots.
This commit changes boot_write_img_confirmed() to instead use
boot_set_next() which sets the confirmed flag for a given flash area
and works with Direct XIP.
DT_CHOSEN(zephyr_code_partition) is used to get the current partition.
The zephyr,code-partition chosen node must be defined.
This commit also adds the zephyr,code-partition chosen node to the
native_sim devicetree to allow the tests under tests/subsys/dfu to
build for this target.
Signed-off-by: Ben Marsh <ben.marsh@helvar.com>
The DRAM range 0xc0000000~0xcfffffff is reserved for the Ethos-U NPU,
so change the RAM base to 0xd0000000.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
remove legacy modem properties and add modem node
compatible to modem subsystem, rak5010_nrf52840
has two variant, one with BG95-M3 and other is
BG96 modem, both are pin to pin compatible.
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Define the reg and size property for the stm32 disco kits
which have an octospi instance
Refer to the dts/bindings/flash_controller/st,stm32-ospi-nor.yaml.
Also remove the <size> property for the stm362h750 disco kit.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Display is not working on STM32F429i-DISC1 board because
display_blanking_off() needs to be sent to ILI9341 device, but it's sent
to LTDC instead which does not implement it.
This patch adds a LTDC DT property that provides the pHandle of the
display's own controller so that display_blanking_off/on are forwarded to
it when they are called by an application.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Add a board that allows to build for the nRF54H20 PPR RISC-V core.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Because both, RISC-V and ARM cores share the same pinctrl driver. The
top level common folder will disappear with the introduction of HWMv2,
where multi-arch SoCs will be well supported.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add targets that allows building for the Application and Radio cores
in the nRF54H20 SoC on the nRF54H20 PDK board.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The mailbox peripheral is actively accessed by stm32_hsem functions,
so mark the device as enabled in DTS.
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
Define the reg and size property for the stm32 boards with qspi inside
Refer to the dts/bindings/flash_controller/st,stm32-ospi-nor.yaml.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Define the reg and size property for the stm32u585 and stm32l562
disco kit.
Refer to the dts/bindings/flash_controller/st,stm32-ospi-nor.yaml.
The stm32l562 reads the sfdp table from the flash itself.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
1. Configure 'core-clock' to 192MHz to generate necessary 48MHz
2. Support workaround to disallowing ISO IN/OUT EPs to be assigned
the same EP numbers
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
drivers: eth: phy: tja1103: Handle link change
These changes enable -
TJA1103 driver to gracefully handle Link connect or disconnect events
between Ethernet PHY and its link partner and notify it to the
upper network layers
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
The DMA is already enabled for this board, but updating the board doc
page to make that clear, and enabling the DMA loop_transfer test.
Signed-off-by: Derek Snell <derek.snell@nxp.com>
GR716A has two SPIMCTRL SPI controllers.
This adds the SPIMCTRL description to the DTS and makes the SPI
option available in the kernel configuration.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
Add support for ADI EVAL-ADIN2111EBZ.
Tested samples:
* hello_world
* blinky
* dhcpv4_client
Co-developed-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Add support for ADI EVAL-ADIN1110EBZ.
Tested samples:
* hello_world
* blinky
* dhcpv4_client
* adt7420
Tested proper SPI detection of the ADIN1110 chip.
Co-developed-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Microchip's PolarFire SoC interface with on-board spi
nor flash via system controller. This on-board spi nor flash can be
used to store FPGA design bitstream's.
Signed-off-by: Harshit Agarwal <harshit.agarwal@microchip.com>
qemu_x86_tiny@768 has coverage enabled by default. Because of
this, it requires more stack space for running tests.
The increases needed are verified via twister.
Fixes#68272
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert ili9xxx display drivers to use MIPI DBI API. Due to the fact
this change requires a new devicetree structure for the display driver
to build, required devicetree changes are also included in this commit
for all boards and shields defining an instance of an ili9xxx display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
add acpi pnp/hw id for pcie node to enable support for retreive
interrupt routing information for pci legacy interrupt via acpi
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
We need to enable this configuration for all R-Car ARM64 boards.
First and foremost, we definitely should run Zephyr on the boards
in the NS-EL1 state. The EL3 is used for TF-A, EL2 is used for
U-Boot, and Xen in the case when we run Zephyr as Dom-0. The S-EL1
is used for OP-Tee, and S-EL0 is used for OP-Tee apps.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
On the Polarfire SOC Icicle Kit the SPI pins are routed to MikroBus.
Enable SPI by default.
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
