Add clarifications to mipi-dbi bindings to avoid the confusion
between two options, write-only and duplex.
Signed-off-by: Eve Redero <eve.redero@gmail.com>
Change reset pin polarity for MIPI DBI SPI controller, so that the board
devicetree is responsible for setting the GPIO to active low, and the
driver always sets the pin to a logic 1 to reset the display.
Fixes#68562
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Unlike SPI nodes, I2C nodes (i2c20, i2c21, i2c22 and i2c30) did not have
this required property.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Remove pinctrl from device tree since it is not required
when internal oscillator is used.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Add FlexSPI clock source to RT1010 devicetree definition for FlexSPI
node, to match FlexSPI clock source defined on standard FlexSPI dt node
that is removed in the RT1010 devicetree.
Fixes#68488
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Display is not working on STM32F429i-DISC1 board because
display_blanking_off() needs to be sent to ILI9341 device, but it's sent
to LTDC instead which does not implement it.
This patch adds a LTDC DT property that provides the pHandle of the
display's own controller so that display_blanking_off/on are forwarded to
it when they are called by an application.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
... so that there is no need to include that header individually
for every added board based on an nRF SoC.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add definition of the nRF54H20 SoC revision EngA with its Application,
Radio, and Peripheral Processor (PPR) cores and basic peripherals:
GRTC, GPIOs, GPIOTE, and UARTs.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add a set of bindings that will be used in the nRF54H20 SoC definition.
Extend the existing GPIOTE binding with properties needed for this SoC.
Also do a tiny clean-up in the bindings added recently for nRF54L15
(HFXO and LFXO).
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... so that it can be included by ARM and RISC-V cores. For the same
reason, SysTick can no longer be disabled in this common file.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This adds new NXP mailbox driver for MBOX device.
NXP mailbox IP driver supports sending data between cores.
It uses 32 bit register to trigger irq to other core.
This driver implementation uses 4 bits for channel selection of
triggering mode, 4 bits for channel selection of data transfer and
rest 24 bits for data.
NXP mailbox IP Reference Manual UM11126, Chapter 52.
https://www.nxp.com/webapp/Download?colCode=UM11126
Signed-off-by: Tomas Galbicka <tomas.galbicka@nxp.com>
Address and size are given by the DTS register property
of the qspi nor. The size Property becomes useless.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Address and size are given by the DTS register property
of the ospi nor. The size Property becomes useless
Signed-off-by: Francois Ramu <francois.ramu@st.com>
1. Configure 'core-clock' to 192MHz to generate necessary 48MHz
2. Support workaround to disallowing ISO IN/OUT EPs to be assigned
the same EP numbers
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
drivers: eth: phy: tja1103: Handle link change
These changes enable -
TJA1103 driver to gracefully handle Link connect or disconnect events
between Ethernet PHY and its link partner and notify it to the
upper network layers
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
GR716A has two SPIMCTRL SPI controllers.
This adds the SPIMCTRL description to the DTS and makes the SPI
option available in the kernel configuration.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
This adds support for the GRLIB SPIMCTRL SPI controller used in LEON and
NOEL-V systems. SPIMCTRL can operate in two different modes: In the
default mode it allows memory-mapped read access to the flash data. When
set in the user mode, it can be used to generate SPI bus transactions.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
Setup rx-clock-source for XIP flash. When running from RAM, the FLEXSPI2
attached SIP flash will be reconfigured, so we must ensure the
configuration used for it is valid.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for reclocking the FlexSPI on NXP iMX RT10XX. This
functionality requires an SOC specific clock function to set
the clock rate, since the FlexSPI must be reset directly
before applying the new clock frequency.
Note that all clock constants are defined in this commit, since the
memc flexspi driver now depends on a clock node being present.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert ili9xxx display drivers to use MIPI DBI API. Due to the fact
this change requires a new devicetree structure for the display driver
to build, required devicetree changes are also included in this commit
for all boards and shields defining an instance of an ili9xxx display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
SPI controllers can easily implement MIPI DBI mode C, with the help of
GPIO pins for the reset and command/data signals. Introduce a MIPI DBI
compliant SPI driver, which emulates MIPI DBI mode C (SPI 3 and 4 wire).
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce MIPI DBI driver class. MIPI DBI devices encompass several
interface types. All interfaces have a data/command, reset, chip select,
and tearing effect signal
Beyond this, MIPI DBI operates in 3 modes:
Mode A- 16/8 data pins, one clock pin, one read/write pin. Similar to
Motorola type 6800 bus
Mode B- 16/8 data pins, one read/write pin. Similar to Intel 8080 bus
Mode C- 1 data output pin, 1 data input pin, one clock pin.
Implementable using SPI peripheral, or MIPI-DBI specific controller.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The LIS2DE12 is an ultra-low-power high- performance three-axis
linear accelerometer belonging to the “femto” family with digital
I2C/SPI serial interface standard output.
This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/en/datasheet/lis2de12.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
add acpi pnp/hw id for pcie node to enable support for retreive
interrupt routing information for pci legacy interrupt via acpi
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
Add a new #nordic,ficr-cells property, so that we can specify a FICR
offset in a phandle-array, e.g.
nordic,ficrs = <&ficr 0xff>;
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This commit adds the `efinix,vexriscv-sapphire` compatible string. This
helps identify the core type from the final devicetree alone.
The VexRiscv core configuration is specific to the Efinix Sapphire SoC.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commits adds two new compatible strings:
* `openisa,ri5cy`
* `openisa,zero-ri5cy`
Adding these two new compats help identify the specific core defined by the
cpu node from the devicetree alone.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds the `andestech,andescore-v5` compatible string. This helps
identify the core tpye form the final devicetree alone.
Andes doesn't define which core type from the v5 series the AE350 SoC uses,
so we're using the whole series name here.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The OpenTitan Earlgrey SoC has the lowRISC Ibex CPU core. This commits adds
the `lowrisc,ibex` compatible string to reflect that.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds the `litex,vexriscv-standard` compatible string. This
helps identify the core type from the final devicetree alone.
The VexRiscv core version is defined in this repository:
https://github.com/litex-hub/zephyr-on-litex-vexriscv.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds the `riscv` compatible string to cpu nodes where it is
currently missing. This is convention is already followed by some cpu
nodes.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
