Add support of r8a779f0 cpg driver.
r8a779f0 soc has its own clock tree.
Gen4 SoCs common registers addresses have been added in header.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Due to a typo it is not possible to select the main oscillator (MOSC) as a
clock source for an RA Microcontroller. This patch resolves the issue.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Do not enable subsystem/driver shell modules by default and stop abusing
CONFIG_SHELL_MINIMAL, which is internal to the shell subsystem, to decide
when to enable a driver shell.
The list of shell modules has grown considerably through the
years. Enabling CONFIG_SHELL for doing e.g. an interactive debug session
leads to a large number of shell modules also being enabled unless
explicitly disabled, which again leads to non-negligible increases in
RAM/ROM usage.
This commit attempts to establish a policy of subsystem/driver shell
modules being disabled by default, requiring the user/application to
explicitly enable only those needed.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Adds a clock control device for a PWM node, allowing the PWM
to be controlled using the clock control API.
It is a similar idea to the device driver in linux:
linux/Documentation/devicetree/bindings/clock/pwm-clock.yaml
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Define max SYSCLK and AHB clock frequencies as 280 MHz, max APB
frequency as 140 MHz, and enable semaphore clock.
Signed-off-by: Charles Dias <charlesdias.cd@outlook.com>
This reverts commit d963900dbd.
Since i.MX 93 is supported by mcux_ccm_rev2, remove i.MX 93 support
from mcux_ccm driver.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
i.MX93 share similiar register layout with i.MX RT11xx. Change ccm driver
to align with i.MX RT11xx, and make it easier to enable other drivers.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
This commit enables clock control on the i.MX8QM and QXP boards.
This is achieved through the following changes:
1) The "reg" property is no longer marked as required
for the "nxp,imx-ccm" binding. This is necessary because
in the case of i.MX8QM and i.MX8QXP the clock management
is done through the SCFW, hence there's no need to access
CCM's MMIO space (not that you could anyways).
2) The DTS now contains a scu_mu node. This node refers
to the MU instance used by the DSP to communicate with
the SCFW.
3) The CCM driver needs to support the LPUART clocks
(which will be the only IP that's supported for now)
and needs to perform an initialization so that the
NXP HAL driver knows which MU to use to communicate
with the SCFW.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Unify spelling of CAN Flexible Data-rate abbreviation to "CAN FD" instead
of "CAN-FD". The former aligns with the CAN in Automation (CiA)
recommendation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add initial support for Renesas RA clock generation circuit.
It returns a fixed value to simplify the first commit to get the UART
working now.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
for nucleo_stm32g0b1 board.
the HSI48 clock is the clock used by default for the USB controller,
however its default tolerance is not enough for the USB specification,
leading to some random errors depending on many factors, including the
upstream HUB or host.
this commit adds an option in the device tree to enable the STM32 Clock
recovery system (CRS) using USB SOF packet reception as a reference,
which brings the HSI48 within the required accuracy for USB transfers.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
Flash is clocked with HCLK, while CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC
reflects SYSCLK. HCLK = SYCLK / AHB prescaler.
When dealing with flash latency, use HCLK instead of SYSCLK.
This changes reverts a abusive change done in an old commit (efd8ee465c)
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Latency should be set before HCLK clock increase. Not doing so can result
in broken behavior.
For instance, at startup, MSI is @4MHz on L4 series.
If MSI is required to be configured at 48 MHz for future use a USB clock,
this will be done in set_up_fixed_clock_sources(). If flash latency is
not correctly set at this point fetching flash will fail..
Move flash latency configuration before setting up fixed clocks.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Based on RM0456, each PLL in the STM32U5 has the
capability to work either in integer or fractional mode.
In this update, the fractional mode can be enabled
by setting the fracn value in the device tree.
Signed-off-by: Jatty Andriean <jandriea@outlook.com>
Add an explicit include of zephyr/arch/cpu.h before fsl_clock.h so that
the Zephyr cpu definitions are parsed before the hal ones.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
According to the reference manual the overdrive should be enabled after
setup of the sysclock (HSE or HSI) and enabling the PLL (PLLON).
The flash latency should be enabled after the PLL has been turned on,
but before switching the system clock to the PLL.
Signed-off-by: Max van Kessel <max_van_kessel@msn.com>
LSI clock configuration for STM32WBA is located in backup domain.
The backup domain needs to be enabled before the LSI can be enabled.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
The CMSIS module glue code was part of arch/ directory. Move it to
modules/cmsis, and provide a single entry point for it: cmsis_core.h.
This entry header will include the right CMSIS header (M or A/R).
To make this change possible, CMSIS module Kconfig/CMake are declared as
external, allowing us to add a new Zephyr include directory.
All files including CMSIS have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This CL introduces new clock architectures in npcx4 series and wraps
clock configurations of different series by device tree files.
For example, the PWDWN_CTLx reg initialization relies on `pwdwn-ctl-val`
prop of pcc DT node now.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
RCX and RC32K oscillators are not precisely trimmed.
This code allows to measure actual frequency of those two
oscillators.
Device tree binding were extended to specify calibration
interval. This interval (in seconds) is used to periodically
call work that will perform oscillator frequency measurement.
For XTAL32K settle time can be provided in device tree.
After this time (depending on actual oscillator used)
XTAL32K is assumed to be stable and low power clock driven by
XTAL32K is considered OK for precise usage in bluetooth.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This is Intel's proprietary IP which supply the clock for all the
system peripherals. Clock manager is initialized only one time
during boot up by FSBL (ATF BL2) based on external user settings.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
STM32H5 series lacked support for MCO configuration.
Added SOC_SERIES_STM32H5X to approperiate kconfig MCO source
configurations. Added new MCO sources from H5 series and
updated the clock_stm32_ll_h5.c with MCO configuration.
Signed-off-by: Kacper Dalach <dalachowsky@gmail.com>
LL name for PLL1Q is not the same across STM32G0, STM32WL, STM32H5 and
STM32H7 families. This allows to choose the proper definition depending on
the family.
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
Create clock_stm32_ll_mco.h file to bring stm32_clock_control_mco_init,
mco1_prescaler, mco2_prescaler, MCO1_SOURCE and MCO2_SOURCE definitions
which were previously in clock_stm32_ll_common.{c,h}. This is done so that
stm32_clock_control_mco_init can be called from clock_stm32_ll_h7.c.
Also update Kconfig.stm32 and add new MCO sources to allow H7 support.
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
Add support of the dedicated STM32F0 14 MHz HSI clock for ADC.
Also remove ADC clock source selection as it is obsolete.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
When the image is chain-loaded, clocks may already by initialized.
The driver was lacking support for already configured HSE and
PLL sources. When CONFIG_ASSERT=y get_startup_frequency was
failing since it did not recognize these sources.
It's the same issue that was addressed in #58109 for stm32u5.
Signed-off-by: Kacper Dalach <dalachowsky@gmail.com>
Add support of r8a77961 SoC to gen3 series.
Create a dtsi file with a common part for both r8a77951 and r8a77961.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Add MMIO mapping for Renesas CPG driver in order to avoid
mappings inside mmu_regions.c file. Remove MMU region for
Renesas CPG driver.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Delete IRQ lock/unlock calls from 'rcar_cpg_mstp_clock_endisable',
because 'rcar_cpg_mstp_clock_endisable' function is always called
under spin lock.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Add associative tables for core and mod clocks.
Add possibility to enable/disable any of core clocks which presents
in the associative table.
Add handler for setting rate to driver and use generic rcar cpg
function for getting rate.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Add associated tables of clocks and API for working with these tables,
from this moment the relationship between clocks and their divider are
built. After set rate of some Core clock, driver has to update all
in/out rates of all childrens recursively. During get/set rate calls
if out rate is unknown, we try to get parent in/out rates and its
divider, in case when parent doesn't have valid in/out rates we get
parent of parent and so on until we get parent with a valid in or out
rates.
Add generic Renesas functions for get/set rate of CPG.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Move cpg log module declare to common rcar cpg file. If the module
consists of multiple files, then LOG_MODULE_REGISTER should appear
in exactly one of them. Each other file should use LOG_MODULE_DECLARE
to declare its membership in the module.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
The clock controller is a singleton controller for all the system-level
clocks (XOSC, PLL, CGM, etc) to provide run-time information to the
peripheral device drivers about the module's clocks.
Clock configuration is not yet supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
