The broadcast audio samples (broadcast_audio_sink
and broadcast_audio_source) are sending mock data,
the apps are improved by using the LC3 module as
the unicast audio samples do.
Signed-off-by: Ping Wang <pinw@demant.com>
Suggest users to use "west config manifest.project-filter +canopennode"
instead of "west config manifest.group-filter +optional" in the sample
documentation to avoid pulling in unrelated, optional modules.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert this sample application build to sysbuild,
and add support for the nrf5340bsim target.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable building this sample on the simulated nrf5340 net
core.
Note that this sample does nothing on its own, as it
requires a companion application core sample to driver it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
PM should not be enabled by default at the soc level. This is an
application decision and not a platform decision whether to enable or
disable PM features.
Enabling PM by default will result in descripencies and test scope and
failures in tests that do not account for PM being enabled.
Fixes#60359
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert this sample application build to sysbuild,
and update documentation.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Make sure DEBUG is enabled if this test is run in CI.
Also re-instantiate CONFIG_PM=y which was abusively removed in a previous
change.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Aliases, including usbc_port0, start counting from zero. This meant
that the DT alias is inconsistent with the port numbering in the
samples. Change the numbering scheme to start from zero to make this
consistent.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Samples sometimes need to identify a default USB-C port. Instead of
hard-coding a node label, use the usbc-port0 alias to point to the
correct node.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Fixes an issue whereby the application init will stall if USB init
failed if it's already been setup, this is likely due to USB CDC
being enabled in which case the failure can be ignored
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
The sample was at the same time filtered for the whole
posix architecture and had native_posix as its integration platform.
This is selfcontradictory.
In any case, this sample cannot run in native_posix but
can run in native_sim.
So let's fix the filtering.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This sample shows how to use flash_mmap() call to enable custom flash
area to be mapped into data region.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Instead of forcing use of NEWLIB_LIBC, select any available complete C
library implementation. Add CONFIG_REQUIRES_FLOAT_PRINTF and adjust
CONFIG_LIBC_MALLOC_ARENA_SIZE as needed.
Signed-off-by: Keith Packard <keithp@keithp.com>
One of the nrfx_uarte event structure members was renamed,
so the sample code has to be aligned.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add installation instruction for adding nanopb to the west workspace.
This is required because it is optional and not installed by default.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Two substests (userspace and rtt) cannot be run in the posix
architecture.
Today they are filtered by kconfig, which works but spends
time running cmake.
As native_posix is a default test platform it is better
to filter it alltogether by arch, which saves quite a lot
of time.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
These samples & tests cannot be run in this architecture
as it does not support userspace.
Today they are filtered by kconfig, which works but spends
time running cmake.
As native_posix is a default test platform it is better
to filter it alltogether by arch, which saves quite a lot
of time.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Compiler can't tell that k_thread_abort() won't return and issues a
warning unless we tell it that control never gets this far.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
In the iso_receive sample, the semaphores were not reset in
each iteration.
This caused the ISO receiver to act incorrectly and cause
issues with some controllers.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The sample enables CONFIG_NET_IPV4_MAPPING_TO_IPV6 and then
turns off IPV6_V6ONLY option which allows it to support both
IPv6 and IPv4 using the same socket.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The BT Core Spec v5.4 allows separate SDU_Interval to
be set on C_To_P and P_To_C directions,
but this is not possible with the existing interface.
This PR splits the interval parameter in the call to
bt_iso_sig_create into one for C_To_P
and one for P_To_C
It also splits the latency parameter into one for
C_To_P and one for P_To_C
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
Bluetooth: ISO: update UI for extended API
The API for setting the SDU interval and latency have been updated.
This PR also updates the setting of these by the user in the shell
and the iso_connected_benchmark sample
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
Fix the west invokation. "-t" is added automatically
to the run goal, otherwise we get a "-t -t" command.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Prevent infinite loop inside interrupt handler when there is incoming
data available and ring buffer is full.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add ADC support for longan nano.
Tested using samples/drivers/adc. Also added longan_nano.overlay
and updated documentation.
Signed-off-by: Maxin John <maxin.john@gmail.com>
Add test script that uses same configuration that the
interoperability test.
This is only checking that unsecure client registers and
responds to a GET query.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Remove gdbstub sample (samples/subsys/debug/gdbstub) as duplicated
by a test (tests/subsys/debug/gdbstub).
Update the GDB stub documentation.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Clone samples/subsys/debug/gdbstub to tests and convert it back
to a build-only sample aligned with documentation.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Enable LVGL widgets demo within Zephyr. This demo requires additional
stack and heap space in order to execute correctly, so raise the stack
and heap size to enable it to run.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The old Makefiles which can be used to build this samples
directly as Linux apps and the description in the READMEs
could be quite missleading.
Building this apps in this way has nothing to do with the
Zephyr native_posix/sim targets. This is about building
them as actual Linux applications without Zephyr or any
HW models.
So let's rename the Makefiles and change the description
in the docs to avoid confusion.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The flash sample and flash shell have implementations that differ
providing similar features.
This commit removes all the code in main.c, only `main()` remains to
reduce redundancy.
Features or improved implementations has not been merged into the flash
shell in this commit.
It should be possible to do in future commits if desired.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add additional RX stats for the BAP broadcast sink so that a
user can easily follow how well the RX is working, and
for several streams.
This also adds some additional logging to better see
what we are syncing to.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This application is no longer needed as we have removed
the automatic startup support which was used by this sample.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This adds a new sample for LVGL that displays a real-time chart for
accelerometer data acquired from &accel0 sensor.
This also adds the appropriate overlays so that the sample can also run
on native POSIX and native sim using emulated BMI160.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add new configuration value CONFIG_LWM2M_UPDATE_PERIOD
that allows calculating update period from last update,
instead of calculating it from the lifetime.
In runtime, server is allowed to change the lifetime of the
registration which causes update perdiod to be effected.
When fixed update period is preferred, UPDATE_PERIOD
config is then used.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Refactor the codec_cfg_get_frame_duration function to return the
assigned numbers value, instead of a converted value, but with
support for converting the value.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Creates a generic sample application that executes a simple charging
task loop capable of completing a basic charge cycle.
Signed-off-by: Ricardo Rivera-Matos <ricardo.rivera-matos@cirrus.com>
Rename the Kconfig option from BT_ISO_ADVANCED to
BT_ISO_TEST_PARAMS to more explicitly denote that it
enables support for using the ISO test parameters.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
When relocating section symbol addresses the value where the
relocation is to be written is an offset into the section to load.
Simply rewriting it with the section address is not enough, we need
to write the address of the section with the offset into it.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
In the broadcast_audio_sink sample there are two pointers defined,
both referencing the same address. We reduce this to one pointer
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
rand32.h does not make much sense, since the random subsystem
provides more APIs than just getting a random 32 bits value.
Rename it to random.h and get consistently with other
subsystems.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The commands showing west build had -b None which isn't quite right. Add
a :board: property with the tdk_robokit1 as its what I tested on myself.
Also noted that llext isn't supported on every architecture but
intentionally left this a bit vague as updating this little comment
every time something is added seems like a recipe for doc rot.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
When using multiple streams the seq_num provided to the
controller would be incorrect as we used a single global
seq_num rather than a proper seq_num per stream.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Update babblesim tests for testing chaining for advertising to ensure that
we spill over to the next PDU
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
Updates the chaining for advertising.
Instead of unconditionally adding a new PDU when new data
is added we now instead fill the last PDU in the chain with
the incoming data, only adding a new PDU when there is
not enough room.
This reduces the nr. of PDUs used for advertising, and also
fixes some qualification failures
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
Follow up on commit f67dd39bb2
("drivers: ramdisk: use devicetree to instantiate RAM disk").
Unfortunately, the additional argument must be passed for the default
build. Using app.overlay would not always help since the sample has few
board-specific overlays.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Update to a fixed percepio tree, which allows the build to pass for valid
version numbers with 0 being one of the version number components.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The percepio build seems to have a bug and fail whenever the major, minor
or patchlevel numeric value is 0:
Invalid version specified: major: 3, minor: 5, patchlevel: 0
Disable the sample until a proper fix is available.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds a sample application that can be used for trying out llext
with the shell. The docs cover how to load a hello world ELF
on to the device, assuming its an arm v7 architecture.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
The conn_mgr_monitor.h was not included so the compilation
gave warning for missing conn_mgr_ignore_iface() function.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Update the function name from codec_cfg_get_chan_allocation_val
to just codec_cfg_get_chan_allocation, and add
codec_cfg_set_chan_allocation.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Added a new event for LWM2M_RD_CLIENT_EVENT_DEREGISTER for
indicate LwM2M client dereistartion.
Updated unit test and sample for new event type
Signed-off-by: Juha Heiskanen <juha.heiskanen@nordicsemi.no>
Demonstrate user function codes with a simple example with a user defined
fc that maps to a function that just increments a counter every time it's
read.
Signed-off-by: Henrik Lindblom <henrik.lindblom@vaisala.com>
mps2_an385 was excluded from networking tests, therefore can no longer
be used as an integration platform. Replace it with qemu_x86.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Describe the code sample using zephyr:code-sample directive to help
with making it easier to find from API reference.
Also cross-referenced main bindesc page from the sample.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Improved the README.md of the hello_bindesc sample by adding a
note about non existing bin files and referencing the relevant
parts of the documentation.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
The original idea of z_current_get() was to be the counterpart
of k_current_get() when thread local variable for current has
not been initialized if TLS is enabled, otherwise they are
the same function. Now since z_current_get() is being used
outside of core kernel, rename it under kernel namespace so
other subsystem can conceptually use them too.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Refactor the codec_cfg_get_freq function to return the assigned
numbers value, instead of a converted value, but with
support for converting the value.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This sample is an alternative implementation of hci_uart. The new sample
differs from the existing sample in that it uses the async UART API
instead of the interrupt driven API.
Included in this commit is a new test for HCI UART flow control. It's
enabled for hci_uart_async. The test can excercise also the existing
hci_uart sample (with some minimal changes to allow compiling in the
mock controller and test suite). The existing hci_uart sample currently
fails the flow control test.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Based on review of the similar charger driver API, it's been demonstrated
from the community that embedding a per value property type when fetching
properties. Separating off the property types from the property values
themselves also allow an array of property types to declared as static
const.
Break up fuel_gauge_property struct into a fuel_gauge_prop_val union and a
fuel_gauge_prop_t property type as inputs into fuel gauge API functions.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
Based on review of the similar charger driver API, it's been demonstrated
from the community that embedding a per value status code when fetching
multiple properties isn't particularly wanted or needed. It was largely
considered not worth the additional maintenance to have the extra per
property error information.
Remove the status field from the fuel_gauge property value structs.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
The fuel_gauge_get_prop() function prototype declares a function that
retrieves multiple fuel gauge properties at once. The naming suggests it
ought to fetch a singular property at a time. Moreso, some clients may just
want to fetch properties one at a time and may feel uncomfortable using a
prototype for fetching multiple properties when wanting to fetch them one
at a time.
Modify fuel_gauge_get_prop() to fetch a single property and add
fuel_gauge_get_props() to support fetching multiple properties. Modify
existing tests/drivers/samples.
This is part of #61818 work.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
After esp32 board was split into several different models,
rpmsg sample code was missing the change. Make esp32_devkitc_wrover
the default option.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Changes the Kconfig symbols for the sys_heap based memory management option
and removes the notion of `BLOCKS` with a more concise single
`LV_Z_MEM_POOL_SIZE` option. Also adds `LV_MEM_CUSTOM` to the lv_conf.h,
since in any option the memory management is considered to be custom.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Update the TLS part of the big_http_download sample to reference the
currently used server used for file download.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The download server that the origin server redirects to seems now to
use different certificate (signed by a different root CA). Therefore
add the additional root CA to the certificate list and refactor the
sample code a bit to allow to easily extend/replace certificates in the
future.
Bump the mbed TLS heap size a bit to accommodate the extra registered
certificate.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Added functionality to change the syslog server's
ip address at runtime as well as sample for
syslog network backend
Signed-off-by: David Corbeil <david.corbeil@dynon.com>
While recent browsers seem to transparently try to use https for
http://www.st.com/... URLs, they are effectively not working anymore, so use
https://www.st.com/... URLs instead.
curl http://www.st.com/en/evaluation-tools/nucleo-g070rb.html -m 5 -v
* Trying 104.89.117.48:80...
* Connected to www.st.com (104.89.117.48) port 80 (#0)
> GET /en/evaluation-tools/nucleo-g070rb.html HTTP/1.1
> Host: www.st.com
> User-Agent: curl/8.1.2
> Accept: */*
>
* Operation timed out after 5002 milliseconds with 0 bytes received
* Closing connection 0
curl: (28) Operation timed out after 5002 milliseconds with 0 bytes
received
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Send a fw ready reply message as soon as possible.
This is usually used on host side which is waiting
for this message in order to establish the
communication with the remote processor - see
imx_dsp_rproc driver from Linux.
This can be enabled by IPM_IMX_FW_READY_REPLY config,
which is by default N.
Set CONFIG_IPM_IMX_FW_READY_REPLY as Y for
openamp_rsc_table sample, running on nxp_adsp_imx8m.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
The table of contents for the samples' catalog was showing too many
levels for some sections.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Excluded cy8cproto_062_4343w and cy8cproto_063_ble from
samples/userspace/shared_mem sample due to a hardware
limitation with number of available MPU regions.
Sample throws warning:
`num_parts of 4 exceeds maximum allowable partitions (2)`
With the Cortex M4 on the boards only 2 mpu regions are left
and available to be used with the sample.
Signed-off-by: Pavlo Havrylyuk <pavlo.havrylyuk@infineon.com>
Update all Nucleo shield samples and references to them so that they
use the new zephyr:code-sample extension.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Running the HTML code through W3C Validator revealed several issues with
the markup that this commit fixes.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Update webusb README with recent changes after index.html was moved to
sample from the external repository.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
tflite-micro now uses MicroPrintf instead of MicroErrorReporter. Update
the samples to use this function instead. AllOpsResolver is now removed
from tflite-micro. AllOpsResolver was also removed in the latest
tflite-micro. Use MicroMutableOpResolver and only include the kernels
used instead.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The stack guard report this testcase has the stack overflow issue. To
fix the issue, slightly increse the stack size.
Signed-off-by: Jaxson Han <jaxson.han@arm.com>
The README file for led_xec sample had several formatting issues
causing it to render very poorly.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Moving from APPLICATION level to POST_KERNEL and keeping both parent and
child on the same level is causing problems, so fix this by putting them
on different priorities in POST_KERNEL.
Also, this sample runs fine in qemu, so make it the integration
platform.
Fixes#62772
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This migrates the subsys code samples to the new Sphinx code-sample
extension, making it easier to find relevant samples when browsing
API reference.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Fix missing Coded PHY implementation conditional compile
causing compile error when disabling Coded PHY support in
SoCs that have radio that support Coded PHY.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed pinout in adc overlays to align with board
Allowed adc driver sample
Added overlay for gpio_basic_api test support
Added overlay for i2c_api test support
Signed-off-by: Pavlo Havrylyuk <pavlo.havrylyuk@infineon.com>
Replace the BT_AUDIO_CODEC_LC3_ID macro with the
BT_HCI_CODING_FORMAT_LC3 as there is no reason to
define and use the LC3 ID different than the other
allowed codec IDs.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Demonstrate use of the Raspberry Pi Pico PIO SPI driver.
Added rpi_pico test cases to sample.yaml
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Modify the bt_bap_broadcast_source_reconfig to use the same
parameter struct as bt_bap_broadcast_source_create so that
the two are more similar, since they both set the same values.
This allow for full control of which subgroups and stream
are updated.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Try to catch issues related to platforms and HAL changes using this
basic sample. We have the same flag for a kernel test, but this is
skipped if no kernel changes are present in the PR, so we were missing
some coverage of platform related changes.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the new code-sample directive and roles to document the networking
samples so that they show up as "Related samples" when browsing the
various relevant networking APIs.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Use the new code-sample directive and roles to document the video
capture samples so that they show up as "Related samples" when browsing
the API documentation.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Use the defind value, BT_APPEARANCE_WEARABLE_AUDIO_DEVICE_EARBUD,
instead of the hard coded "magic numbers".
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The sample did not properly include the source
context in the advertising data.
It also set different contexts for PACS and the advertising data
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Rework RAM disk driver to be configured using devicetree and
support multiple instances.
This patch also removes a copy of the RAM disk driver,
tests/subsys/fs/fat_fs_dual_drive/src/disk_access_test_drv.c,
that was there for testing multiple disk drivers support.
Bonus: one SYS_INIT() less and a memory region can be exported to the
host.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The fuel gauge API uses separate get/set property structs to indicate what
properties are readable or writable. This lead to duplication in property
names and potential confusion for new users of the API. See issue #61818.
In addition to above, drivers already determine at runtime if a property is
supported for read or write actions.
Join the get/set fuel gauge property structs as a single struct.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
The mr_canhubk3 board enables by default an off-chip watchdog that must
be serviced to avoid triggering a reset and cannot be disabled on a
per-test basis.
The amount of data printed on this test prevents to initialize the
on-board watchdog within the expected window, causing a board reset.
Hence do not run the test on mr_canhubk3 board.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Convert the driver to a dt-based device. Also update Kconfig so that it
depends on the right compatible being enabled, initialize in POST_KERNEL
(APPLICATION should not be used for devices) and remove one redundant
include.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Introduce a helper function zephyr_nanopb_sources to generate
source files and add these to a target.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
This is the final step in making the `zephyr,memory-attr` property
actually useful.
The problem with the current implementation is that `zephyr,memory-attr`
is an enum type, this is making very difficult to use that to actually
describe the memory capabilities. The solution proposed in this PR is to
use the `zephyr,memory-attr` property as an OR-ed bitmask of memory
attributes.
With the change proposed in this PR it is possible in the DeviceTree to
mark the memory regions with a bitmask of attributes by using the
`zephyr,memory-attr` property. This property and the related memory
region can then be retrieved at run-time by leveraging a provided helper
library or the usual DT helpers.
The set of general attributes that can be specified in the property are
defined and explained in
`include/zephyr/dt-bindings/memory-attr/memory-attr.h` (the list can be
extended when needed).
For example, to mark a memory region in the DeviceTree as volatile,
non-cacheable, out-of-order:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_VOLATILE |
DT_MEM_NON_CACHEABLE |
DT_MEM_OOO )>;
};
The `zephyr,memory-attr` property can also be used to set
architecture-specific custom attributes that can be interpreted at run
time. This is leveraged, among other things, to create MPU regions out
of DeviceTree defined memory regions on ARM, for example:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-region = "NOCACHE_REGION";
zephyr,memory-attr = <( DT_ARM_MPU(ATTR_MPU_RAM_NOCACHE) )>;
};
See `include/zephyr/dt-bindings/memory-attr/memory-attr-mpu.h` to see
how an architecture can define its own special memory attributes (in
this case ARM MPU).
The property can also be used to set custom software-specific
attributes. For example we can think of marking a memory region as
available to be used for memory allocation (not yet implemented):
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_NON_CACHEABLE |
DT_MEM_SW_ALLOCATABLE )>;
};
Or maybe we can leverage the property to specify some alignment
requirements for the region:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_CACHEABLE |
DT_MEM_SW_ALIGN(32) )>;
};
The conventional and recommended way to deal and manage with memory
regions marked with attributes is by using the provided `mem-attr`
helper library by enabling `CONFIG_MEM_ATTR` (or by using the usual DT
helpers).
When this option is enabled the list of memory regions and their
attributes are compiled in a user-accessible array and a set of
functions is made available that can be used to query, probe and act on
regions and attributes, see `include/zephyr/mem_mgmt/mem_attr.h`
Note that the `zephyr,memory-attr` property is only a descriptive
property of the capabilities of the associated memory region, but it
does not result in any actual setting for the memory to be set. The
user, code or subsystem willing to use this information to do some work
(for example creating an MPU region out of the property) must use either
the provided `mem-attr` library or the usual DeviceTree helpers to
perform the required work / setting.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Use the new code-sample directive and roles to document the filesystem
samples so that they show up as "Related samples" when browsing the API
documentation.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add a MBOX driver wrapper around the NXP MU, simular to
the existing wrapper around the NXP S32 MRU. This allows Zephyr IPC
to work based on the MU, on a number of NXP boards.
Also update the SHA of NXP HAL to enable the Kconfig for this driver.
Signed-off-by: Yicheng Li <yichengli@google.com>
To achieve minimal power consumption, only the console (ie UART) needs
to be suspended. Note that this is a temporary workaround, UART driver
should be using device runtime PM so that this is not needed.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Wake-up from pin is already supported when configuring GPIO interrupt as
GPIO_INT_LEVEL_ACTIVE, so there's no need to resort to HAL.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Fixtures in pytest-twister-harness plugin are moved to one
file to simplify adding new fixtures in the future - no
need to add pytest_plugins entry and register asserts.
Moved also shell fixture from sample dir, because that
fixture can be reused in new tests.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
This modification frees up around ~10kB of RAM and make sample code
working again.
1) Reduced net packet size and count.
2) Increase Wi-Fi heap to avoid memory allocation failure.
3) Keep log as minimal.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Add RK055HDMIPI4M specific testcase to LVGL. This allows LVGL to be
verified on the RT1170 and RT595 EVKs from NXP, which support LVGL using
this shield.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Instead of depending on the nRF5340 DK, use a path specific to just
the nRF5340 SoC and get the size of the external flash in this case
from devicetree so that the sample could be easily run on other boards
based on the nRF5340 SoC (after just adding proper overlays).
On the occasion, correct the attributes of the EXTFLASH memory region.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the Nordic QSPI NOR flash driver instead of the specific code
for the nRF5340 DK to initialize the external flash chip for XIP.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Adds a zephyr,lvgl-encoder-input compatible to the native_posix board
overlay and the required code to control an arc widget.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
This commit follows the parent commit work.
This commit introduces the following major changes.
1. Move all directories and files in 'include/zephyr/arch/arm/aarch32'
to the 'include/zephyr/arch/arm' directory.
2. Change the path string which is influenced by the changement 1.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
It doesn't make sense to keep the aarch32 directory in the
'arch/arm/core' directory as the aarch64 has been moved out.
This commit introduces the following major changes.
1. Move all directories and files in 'arch/arm/core/aarch32' to
'arch/arm/core' and remove the 'arch/arm/core/aarch32' directory.
2. Move all directories and files in 'arch/include/aarch32' to
'arch/include' and remove the 'arch/include/aarch32' directory.
3. Remove the nested including in the 'arch/include/kernel_arch_func.h'
and 'arch/include/offsets_short_arch.h' header files.
4. Change the path string which is influenced by the changement 1
and 2.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
- Updated basic samples READMEs to use the new zephyr:code-sample::
directive. Dropped "-sample" suffix that's not required anymore now
that samples have their own namespace.
- Updated all references to the samples to use the :zephyr:code-sample:
role. Checked and updated the wording of said references to account
for the fact that samples should not have "... sample" in their name
anymore.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This is a private kernel header with private kernel APIs, it should not
be exposed in the public zephyr include directory.
Once sample remains to be fixed (metairq_dispatch), which currently uses
private APIs from that header, it should not be the case.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
cipher_list and sec_tag_list are used only with zsock_setsockopt
in MQTT. For that use, they can be const (and potentially kept
in flash memory).
Signed-off-by: Miika Karanki <miika.karanki@vaisala.com>
Avoid to build with debug log level enabled and instead register the
test log modules with debug level.
mr_canhubk3 board will fail to initialize the on-board watchdog within
the expected window triggering a reset, due to the amount of log
messages being printed. Other boards may face similar issues.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Added lvgl-pointer definition in devicetree, to enable
touch-support in lvgl applications.
Kscan support has been removed from m5stack_core2 as this was just a
temporary thing.
Has been tested with lvgl hello world sample.
Signed-off-by: Martin Kiepfer <m.kiepfer@teleschirm.org>
Use the new code-sample directive and roles to document the zbus samples
so that they show up as "Related samples" when browsing zbus API.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This commit adds a callback to the button to reset the counter when the
button is pressed. The button is automatically created when lvgl
pointer or kscan support is enabled. The same reset functionality was
already available for possible gpio button.
Please make sure to define a zephyr input device in device
tree (e.g. "zephyr,lvgl-pointer-input").
Signed-off-by: Martin Kiepfer <m.kiepfer@teleschirm.org>
Google Cloud IoT Core has been retired on August 16, 2023.
Removed the sample and the link to it in a previous release note.
Added a redirect to other IoT cloud samples.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Exclude qemu_arc_hs5x from the test, seems to fail since f0daf90. Other
ARC platform works so let's exclude this one while the issue is
investigated.
Link: https://github.com/zephyrproject-rtos/zephyr/issues/62405
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
32a9d13d61
introduced a new required tag for this test
which the integration platform does not "support"
causing the testplan generation to error out.
Fix it by removing the offending tag from the test.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The previous design with dedicated bits in the structure required a
user to explicitly set each bit.
Using one flags variable allows to extend the features more easily
in the future and avoids breaking existing code.
This change is particularly useful for the FDF and BRS flags required
for CAN-FD support.
See also previous similar change for the CAN driver in
f8a88cdb27
Signed-off-by: Martin Jäger <martin@libre.solar>
To avoid confusion having both a 'tfm' and a 'trusted-firmware-m' tag,
remove the old 'tfm' tag entirely. Any external test frameworks that are
using the 'tfm' tag will need to be changed to account for this.
Signed-off-by: David Brown <david.brown@linaro.org>
In addition to running the tfm tests when the trusted-firmware-m module
changes, most of the tests also use MCUboot, which comes from our module.
Add the mcuboot tag to each of these tests, except for the single test that
explicitly builds without using MCUboot.
Signed-off-by: David Brown <david.brown@linaro.org>
A recent change #61718, adds support to the twister build to check for
manifest changes, and run tests using tags based on the modules that have
changed. The tfm tests have an existing tag `tfm` to select these tests,
but the above patch uses a tag named after the module, trusted-firmware-m.
To make this work, add `trusted-firmware-m` in addition to the existing tag
`tfm` so that these tests will run whenever the tfm module is updated.
Signed-off-by: David Brown <david.brown@linaro.org>
zephyrproject/zephyr/samples/philosophers/src/main.c: In function
'philosopher':
zephyrproject/zephyr/include/zephyr/sys/__assert.h:44:52: warning:
format '%u' expects argument of type 'unsigned int', but argument 2 has
type 'stack_data_t' {aka 'long unsigned int'} [-Wformat=]
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
In this board, there are eight PWM channels from
EMIOS 0 CH0 --> EMIOS 0 CH7 that can be used to
generate PWM pulse to outside of the board.
Moreover, there are three RGB leds that can use
PWM pins for blinking, faded leds
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This variable was originally provided for two indended purposes:
* Let users manually add a new image in a desired order in the list.
* Let users set build-only images, which are excluded from the list.
Given the recent additions of the `sysbuild_add_dependencies()` function
and the `BUILD_ONLY` parameter, `IMAGES` should be considered obsolete.
Furthermore, the list of images added to sysbuild should be updated
automatically when calling `ExternalZephyrProject_Add()`. This is now
possible by using a GLOBAL property internal to sysbuild.
With that, the `IMAGES` variable can be removed. Its existing usage for
image ordering is replaced with `sysbuild_add_dependencies()` treewide.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
After adding the lvgl pointer device into the board dts the custom overlays
are not needed anymore.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Modify the signature of the k_mem_slab_free() function with a new one,
replacing the old void **mem with void *mem as a parameter.
The following function:
void k_mem_slab_free(struct k_mem_slab *slab, void **mem);
has the wrong signature. mem is only used as a regular pointer, so there
is no need to use a double-pointer. The correct signature should be:
void k_mem_slab_free(struct k_mem_slab *slab, void *mem);
The issue with the current signature, although functional, is that it is
extremely confusing. I myself, a veteran Zephyr developer, was confused
by this parameter when looking at it recently.
All in-tree uses of the function have been adapted.
Fixes#61888.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The logs were not visible when an assert fired on the controller and
`CONFIG_BT_HCI_VS_FATAL_ERROR` was not set.
Putting the logs in panic mode before entering the infinite loop fixes
that.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Update build documentation for openamp sample, to reflect that sysbuild
is required when building this sample. Sysbuild is needed to build both
core images in one step.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
k_cycle_get_32() expands to RTC->COUNTER in nrf_rtc_counter_get(),
sys_clock_hw_cycles_per_sec() expands also properly.
Signed-off-by: Witold Lukasik <witold.lukasik@nordicsemi.no>
This sample uses the DEVICE_DT_GET_ONE(COMPAT) to select the ps2 device
for a specific chip. This commit changes it to use the aliases to
let more chips which support the ps2 driver can build this sample.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
This commit adds a sample application which demonstrates how
to use the new driver and modules. The sample uses power
management to turn on the modem, uses network management
to wait for L4 connected, then uses DNS to get the IP
of the server running the python script found in the
server folder, which echoes back data recevied to it.
A packet containing psudo random data is then sent to
the server, which the echoes it back. To validate the
capability of the driver to restart the modem, the
modem is restarted, and the packet is sent again.
The server is hosted by linode, and uses the domain
name test-endpoint.com
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
Config CONFIG_NATIVE_UART_0_ON_STDINOUT=y should be applied only for
posix architecture platforms.
Signed-off-by: Piotr Golyzniak <piotr.golyzniak@nordicsemi.no>
Create helper class Shell which can be used in tests which require
interaction with shell application.
Signed-off-by: Piotr Golyzniak <piotr.golyzniak@nordicsemi.no>
Add readlines_until method to DeviceAdapter class to simplify using
adapters in tests by give user possibility to read output from device
until following conditions:
- provided regex was found
- provided number of lines was already read
- timeout was occurred
Signed-off-by: Piotr Golyzniak <piotr.golyzniak@nordicsemi.no>
Select and place common code of three adapters (HardwareAdapter,
BinaryAdapterBase and QemuAdapter) into basic DeviceAdapter class.
Introduce new way of reading device output by run separate thread which
try to read device output and place it into internal python queue.
Thanks to this, now it is possible to create readline method for all
adapters, which can be unblock when timeout occur.
Collect all common steps which have to be done before setup device in
launch method. The same was done for teardown operations which were
placed into close method.
Additionally some protection mechanisms were introduced to prevent for
undesirable side-effects when user could try to launch to already
launched device or try to send some data to disconnected device.
iter_stdout method was replaced by two new methods: readline and
readlines. To make it possible to remove all read output from internal
buffer (queue), clear_buffer method was introduced.
Also unit tests were rewritten to work properly with current version
of adapters.
Signed-off-by: Piotr Golyzniak <piotr.golyzniak@nordicsemi.no>
- Remove unnecessary includes
- Remove redundant definitions (sample is not portable anyway)
- Use printf
- Check for device readiness
- Do not check for zero ticks (not possible for the given
timeout/driver), also, driver should likely error for such case anyway
- Check for all error codes
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The connectivity monitoring subfeature of conn_mgr is currently also
named conn_mgr, which is confusing.
This commit renames it to conn_mgr_monitor, or conn_mgr_mon for short,
for clarity.
Signed-off-by: Georges Oates_Larsen <georges.larsen@nordicsemi.no>
Remove the qos field from
bt_cap_unicast_audio_start_stream_param as it was not used.
The QOS values are set when creating the unicast group,
and not when starting the streams.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Replace the `CONFIG_ZBUS_RUNTIME_OBSERVERS_POOL_SIZE` with the
`CONFIG_ZBUS_RUNTIME_OBSERVERS` and add the heap. Add user_data to hello
world sample iterator functions.
Signed-off-by: Rodrigo Peixoto <rodrigopex@gmail.com>
Adds a lvgl-button-input pseudo device to the lvgl sample. Triggering the
SDL gpio (pressing 'b') on the keyboard should trigger a click event at the
center of the screen.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Changes all board specific configurations to use the new
zephyr,lvgl-pointer-input compatible. The kscan_input node in the boards
remains to have downstream backwards compatibility.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Refactor the bt_audio_codec_cfg to use flat arrays to store
metadata and codec specific configurations.
The purpose of this is to make it easier to copy the data
between layers, but also to support non-LTV data for non-LC3
codec configurations.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
CONFIG_COVERAGE has been incorrectly used to
change other kconfig options (stack sizes, etc)
code defaults, as well as some samples behaviour,
which should not have dependend on it.
Instead those should have depended on COVERAGE_GCOV,
which, being the one which adds special code and
temporary RAM storage for embedded targets,
require changes to many features.
When building for the native targets, all this was
unnecessary.
=> Fix the dependency.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The CMSIS module glue code was part of arch/ directory. Move it to
modules/cmsis, and provide a single entry point for it: cmsis_core.h.
This entry header will include the right CMSIS header (M or A/R).
To make this change possible, CMSIS module Kconfig/CMake are declared as
external, allowing us to add a new Zephyr include directory.
All files including CMSIS have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This removes odd `subscribe` parameter from bt_tbs_client_discover
function parameters list. As the API user enables specific
CONFIG_BT_TBS_CLIENT_* option, the client implementation should
subscribe to the characteristic notifications so that the user receives
the value updates.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
With gcc from the zephyr sdk and -Wold-style-declaration is giving this
output:
zephyr/arch/arm/core/aarch32/cortex_a_r/fault.c:101:1: warning:
'inline' is not at beginning of declaration [-Wold-style-declaration]
101 | static void ALWAYS_INLINE
z_arm_fpu_caller_save(struct __fpu_sf *fpu)
| ^~~~~~
I searched to all of the source code to find these further occurances
where inline is not at the beginning of a function declaration.
Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>
The XEC clock control driver sample code uses enum indexes to offset to
the desired GPIO CTRL register of the package. These enums are only
used in this example code and are being removed in favor of calculated
indexing into the specific GPIO register memory map.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Add simple TFTP client code using TFTP client library
Initiate connection (IPv4) with optional DNS resolution
Operate get operation then put operation in octet mode
Tested on native_posix
Issue/Discussion #60985
Signed-off-by: romain pelletant <romain.pelletant@fullfreqs.com>
Remove print_sys_memory_stats() from hash_map example as it is not used
there at all. For sys_heap make this a static function.
Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>
Exit the sample if creation of any of the RX threads failed. Name the
threads to aid in debugging and monitoring of this sample.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Increase the stack size of the two RX threads used in the ISO-TP sample
from 512 to 1024 bytes as the former is too small for some CAN
controller/SoC combinations.
Make both the RX thread stack size and priority configurable via Kconfig.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
As the metadata has to be validated anyway, let the initial vaidation of
metadata to be done in ASCS. The application can still reject the
metadata, but the length validation and supported type validation can be
performed by the stack.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
The sample will leverage shell_thread function, which is not SMP-safe.
This will cause issues on some SMP platform. Set CONFIG_MP_MAX_NUM_CPUS
to 1 to fix the issue.
Signed-off-by: Jaxson Han <jaxson.han@arm.com>
NET_TEST is the approprite config for networking tests that do not
require a network device. This has the same effect of disabling
NET_SLIP_TAP, but also disables other network devices. This is required
to disable e1000 Ethernet driver on the qemu_cortex_a53 board.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
The benchmark duration is in nanoseconds, and it logs the duration to
the console in seconds. The conversion is wrong for scenarios where
the execution lasts less than 100 milliseconds. Fix that by adding
leading zeros while printing duration.
Signed-off-by: Jilay Pandya <jilay.pandya@zeiss.com>
This commit adds a new sample to zbus that shows how to implement a
confirmed channel. Developers commonly asked about similar features on
zbus discord channel and RFC (in the past). Adding this sample, we can
show developers how to solve their needs (confirmed channels) without
zbus changes.
Signed-off-by: Rodrigo Peixoto <rodrigopex@gmail.com>
Updated the sample to check for lines from the tracing user
implementation to make sure that the glue works.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Let's just let the user implementation to its things, like
checking, locking and stuff.
The tracing_user.c now just acts as a glue.
Moved previous implementation to its sample, and cleaned up
headers.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Instead of printk. This change aligns the sample a bit more to the
canonical "hello world" sample in C. Also, samples should in general be
as portable as possible.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Overall, this makes the sample code much simpler and smaller.
Whit the changes introduced in commit commit 57e0da4d80
("boards: add zephyr,code properties to the various gpio-keys nodes")'
this example will work out of the box with any board that has at least
zephyr,code = <INPUT_KEY_0>; in its devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Because there are more comprehensive examples in the Zephyr's
example-application repository. Application development samples page now
points to example-application as well.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Because example-application contains relevant sample code related to
application development.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The default nRF hardware PWM driver is not very suitable for this
sample as that driver does not allow setting a period longer than
~262 ms. Use the nRF SW PWM driver instead. This will also ensure
that the driver is built by CI for nRF52, nRF53, and nRF91 Series.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Since the driver can now be also used on nRF91 Series, its name need to
be updated to not cause confusion.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of sending the user out of the documentation site to GitHub
to read the testing instructions, link to the generated page for the
documentation.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
This follows the same convention that has already been adopted by Intel
Alder Lake and Raptor Lake boards.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add `yd_esp32` board:
- Model name: YD-ESP32
- Manufacturer: VCC-GND® Studio
- Espressif module: ESP32-WROOM-32E
Signed-off-by: Julio Cesar <hi@jcsx.dev>
There is no reason why the capabilities
should be modified by the stack after registration,
nor any reason why a the unicast client application
needs to modify the reported remote capabilities, so
all have been marked as const.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Refactor the bt_audio_codec_cap to use flat arrays to store
metadata and codec specific capabilities.
The purpose of this is to make it easier to copy the data
between layers, but also to support non-LTV data for non-LC3
codec capabilities.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The broadcast sink API has been modified so that all scanning, etc.
will be done by the application, rather than the stack. This commit
updates the sample to use this updated API.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The broadcast sink API has been modified so that all scanning, etc.
will be done by the application, rather than the stack. This commit
updates the sample to use this updated API.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This is following the same convention that was recently introduced to Alder
Lake boards (intel_adl). Additionally, an "S" suffix is added to the
boards, since what's currently supported is in fact the Raptor Lake S
variant.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A sneaky whitespace was causing inconsistent rendering in the list of
available overlays.
Fixed by switching to a list table which is arguably now even easier to
read.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add a config entry specifically for RISC-V runtime.
Memory usage is 7066 bytes.
Also adjust some library options. This make the ARC runtime binary
smaller as well:
before:
FLASH: 8808 B
SRAM: 3672 B
after:
FLASH: 5596 B
SRAM: 3672 B
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Remove unneeded board configurations since those now selected with
selecting PCH SMBUS driver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
TC "test_single_shot_alarm_notop" is failing because there were 2 ISR
callbacks instead of one. this is because of invoking
ifx_cat1_counter_set_int_pending incorrectly. Updated
ifx_cat1_counter_set_alarm to fix this
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Since 3a197934fc
main() should be int main(void) instead of void main(void)
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Since 3a197934fc
main() should be int main(void) instead of void main(void)
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add an optional compare buffer to check each byte. If the byte differ
the read value will be printed as an error.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add an optional compare buffer to check if bytes read
match a provided buffer and print an error if they differ.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The DTC_OVERLAY_FILE variable is specified on the command line.
It's not preferable to set it in CMakeLists.txt.
The app.overlay file is used as the default overlay file, so use it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
This board is a relatively inexpensive development kit for USB-PD
controllers, using an UPD301C controller.
This Zephyr config includes support for:
* UART (present on he debug header of the board), tested with the
hello_world sample application;
* the one standalone LED (CAP_MIS), tested with the blinky sample
application;
* the rotary encoder (PDO_SEL), via ADC, tested with the adc sample
application;
* the current sense amplifier (I_SENSE), currently untested;
* the SPI bus, connected internally in the UPD301C to the UPD350;
* the I2C bus, exposed on the debug header, currently untested.
Note that the drivers.uart.async_api.rtt has to be disabled, as it is
for other m0 boards with no dma or it fails to build.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
Add support for apollo4p_evb to the counter alarm sample.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Maciej Sobkowski <msobkowski@antmicro.com>
Add gpio-keys codes for all boards. These are mostly INPUT_KEY_0 and so
on but I've used some more specific ones where it was obvious that
there's something else on the boards.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add overlays for esp32s2, esp32s3, esp32c3 based boards, which
has RGB led assembled. Those boards are capable of driving the
RGB led using SPI. The default MOSI idle level is different
to how DI driver expect it to be.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Fixes a minor documentation issue and suggests/documents additional RTT
tracing and logging options.
Showcases logging via RTT UART which is now available w/o restrictions
due to the preceding change. This has been tested on CC13/26xx hardware.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Make use of the new sys_poweroff API to actually power off the system.
This lets us remove many hacks present in the sample.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Some boards may have less LED child nodes in the DT than the maximum
number of LEDs supported by the chipset. For these boards, the channel
test must skip the missing LEDs when preparing the color buffer and not
exit in error due to missing info.
Also, some boards may have a color mapping that is different from RGB
and this mapping should be used when providing the buffer to
led_set_color().
Signed-off-by: Mathieu Anquetin <mathieu.anquetin@groupe-cahors.com>
Add support for LP5009, LP5012, LP5018 and LP5024 devices which only
differ by the number of LEDs they can control.
Also, update application sample to run on all these new supported
devices.
Based on initial work from:
- Marek Janus <marek.janus@grinn-global.com>
- Rico Ganahl <rico.ganahl@bytesatwork.ch>
Signed-off-by: Mathieu Anquetin <mathieu.anquetin@groupe-cahors.com>
The system still takes both prefixed and unprefixed dt-bindings files,
but let's use zephyr/ prefixed in the examples and documentation.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
There is no need to use SYS_INIT as the HID specific initialisation
can be done in the main before the usb_enable() call.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add no-timers configuration to sample.minimal to check that
it's actually working in runtime.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
This board has a single instance of EMAC connected to a NXP TJA1103
Ethernet PHY. Currently, there is no driver for this PHY and its
pin strapping configuration allows to use it without software
configuration, so EMAC is configured as fixed link.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Use 64bit timestamps from k_uptime_get() so they don't
roll over during the expected device lifetime.
Fixes#60826
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Allow socket-loop to wake up immediately, if there are changes,
instead of waiting for zsock_poll() to timeout.
This change makes engine more reactive and removes
hard coded timeout from zsock_poll().
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Add new sample scenario without using a hardware watchdog as fallback.
This is used for the moment only for the mr_canhubk3 board, but a
generic configuration is introduced that can be used by other boards if
needed.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
This watchdog doesn't allow to stop on CPU halt by debugger.
It also requires a minimum window value different than zero
so that the watchdog is refreshed during the open window.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add (optional) advanced ISO support for the benchmark ISO
sample. The CONFIG_BT_ISO_ADVANCED Kconfig simply needs to
be enabled in order to support the advanced settings.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add (optional) advanced ISO support for the benchmark ISO
sample. The CONFIG_BT_ISO_ADVANCED Kconfig simply needs to
be enabled in order to support the advanced settings.
This also reduces the number of default channels supported
to 1.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add the overlay for running the samples/subsys/nvs/ application
on the nucleo_g474re. Define a 6kB storage_partition at the end of the
512kB flash.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enable all channels that available connector on board.
ADC0 channel 6 on precision group with normal end chain
callback.
ADC1 channel 2 on precision group with normal end of
conversion callback.
ADC2 channels 3, 4, 5 on precision group with normal end
of conversion callback.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
