Add a symbol to enable GNU C Extensions. And a hidden option for
toolchains to signal GNU Extensions support.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Add symbols to select a C standard. Next to an option, hidden symbols
are available to select the minimum.
This allows subsystems or modules to select the least compliant C
standard supported.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
There is no need to make this optional just inform user that
this has to be called to complete write of buffers.
The commit also adds info that there should be no more write
attempts done with use of "flushed", as it may return write
errors anyway.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
I am using the tracing module using the RAM backend on a system with
limited RAM & a buffer that can only store 300ms of tracing data. Current
tracing module starts recording during boot-up & we run out of memory prior
to executing code we actually want to trace.
By reseting buffer metadata here, I can call init() at an arbitrary point
of program execution & the tracing module will reset & start tracing.
I tested on E2E on an ARM M-class MCU by calling init & then reading
buffered tracing data via GDB
Signed-off-by: Galen Krulce <gkrulce@meta.com>
Similar to logging module, allow application specific extension of
shell fprintf APIs at a macro level.
Signed-off-by: Al Semjonovs <asemjonovs@google.com>
Add PHYTEC's phyBOARD-Electra kit with the phyCORE-AM64x
System on Module (SOM).
This board only supports the M4F core, UART and GPIO right now,
since other drivers are still missing.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
This file is basically a copy of the AM62x M4 dtsi but an
additional mcu_uart1 interface.
The internal clock frequency feeded into the UART IP is
96 MHz instead of 48 MHz, which is different to the AM62x.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
We define two frequencies in the am62x_m4.dtsi file.
Use DT_FREQ_M for both frequency to make them more
human-readable and easier to understand.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The AM64x and AM62x are both SOCs from the TI K3 family
and share common architecture designs. The M4F subsystem
is actuall identical on both SOCs.
Therefore, just add all missing CONFIGs, files, etc. to
support the AM6442x SOC.
Since MMR and RAT initialization are identical too, both
functions can be re-used. However, since they might
differ in the future, the am64x has it's own init
function.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Fix incorrect note that write only allows to change value of
bit to zero, where proper information is that change is only allowed
from erase-value to the opposite.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit adds missing binary or in write operation.
Assuming that program-erase devices only allow switching bits
from erase-value to opposite, in case of 0x00 erase value device
only ones can be written.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit restricts erase-value to either 0xff or 0x00.
On program-erase type devices writes can only change from
erase value of bit to opposite, ease usually consists of two
operations which is programming the opposite value to every bit
of erase range and then turning back all bits to the "erase-value";
above makes it impossible to have erase value of device to be other
than 0xff or 0x00.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Improve the default serial backend init level.
The documentation says to be bigger than the init level of the serial
device used. Since serial devices default to the kernel device init
level (50) then put this to default of application level drivers (90).
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Configure SDMMC port on stm32h573i_dk.
Disable SDMMC clock check as using 48MHz is not strictly required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
This implements basic driver to utilize the I3C IP block
on NPCX.
1. I3C mode: Main controller mode only.
2. Transfer: Support SDR only.
3. IBI: Support Hot-Join, IBI(MDB).
Controller request is not supported.
4. Support 3 I3C modules:
I3C1(3.3V), I3C2(1.8V, espi mode), (I3C3 1.8V or 3.3V)
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
During DAA, the responding device might not be in the device list.
This CL adds target device descriptor's pointer checking to prevent
getting unexpected results.
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
1. The only valid values of MCLKD clock frequency
are between 40Mhz to 50Mhz.
2. If DMA is used, the APB4_CLK clock frequency must
be equal to or higher than 20Mhz.
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
Prevent the CPU from entering deep doze mode when JTAG debug is enabled.
Additionally, The CPU address from 0x80000800 to 0x800008FF should be
reserved for JTAG debug usage. This commit reserves the area from the end
of the reset section to 0x800008FF if JTAG debug is enabled.
Tested with:
- west build -p always -b it82xx2_evb samples/hello_world/
-DCONFIG_SOC_IT8XXX2_JTAG_DEBUG_INTERFACE=y
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
Add aux offset population assertion check, to ensure the
aux offset calculation is completed before the primary
PDU is setup for transmission.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Found via static analysis. In `can_mcan_state_change_handler`, the
return value of `can_mcan_get_state` is not checked for error. In the
event of an error, both `err_cnt` and `state` are left unitialized and
accessed downstream.
The correct behavior is to return early in that case.
Signed-off-by: François Baldassari <francois@memfault.com>
Commit fixes behavior when provisioning protocol accepts
incoming transaction before ongoing tx transaction is
still active (device didn't receive acknowledgement yet).
Incoming data are ignored until ack is not received.
Specification:
5.3.3 Generic Provisioning behavior
...
If the sender receives a Transaction Acknowledgement
message, then the transaction has completed.
If the sender receives a message with other PDU types,
then the message shall be ignored.
...
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Report more information and do not use `dev->name` so that what the
sample prints looks less similar to the GNSS dump logs.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
- Configure a UART TX buffer; the backend would otherwise assert in
its configuration or (if the asserts are off) miserably fail when
trying to send anything to the GNSS modem.
- Fine tune the UART RX buffer size and make it depend on whether
satellite data is received.
- Remove unused k_spinlock.
- Make declaration of Kconfig items dependent on GNSS_NMEA_GENERIC
conditional.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
As of now only the resume action is supported, and doesn't perform
any power action on the GNSS modem.
It allows to initialize the GNSS driver later than it would otherwise
be.
Also, the driver now runs a modem-specific chat script on resumption.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Those helpers allow to define some typical kinds of chat matches and
scripts with more ease/less boilerplate.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Clang warns the user whenever an ISR invokes a function that is not
marked with the `interrupt` attribute. This applies to the whole call
chain, which makes it unfeasible to add the attribute to add it to all
functions.
Instead, disable the clang warning just like it was done for the
equivalent GCC one in 5b3f80094e.
See also:
https://reviews.llvm.org/D28820
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bump tj-actions/changed-files to v44.
As of v42, input file patterns that end with a / now match all sub-files
within the directory without requiring to specify the globstar pattern.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
There have been to problems with the code where zcbor_bool_encode
has been fed value instead of expected pointer and the result
of previous zcbor_encode operations has not been taken to evaluate
value of ok status.
The change also replaces usage of #if IS_ENABLED with #ifdef, as
IS_ENABLED should not be used outside if().
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Reintroduce the overlays for native_sim/native/64 and
native_posix/native/64 to verify all bitrates on those platforms.
These were removed in fddbd79cf7.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
