Have the driver default to UART_CFG_PARITY_NONE if no parity property
exists rather than using default in binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
'remap' value can never be REMAP_FULL for usart.
Fix this value depending on the usart instance.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Refactoring poll_out to be ready for handling preemption. uart_tx and
uart_fifo_fill modified so they are resilient to being preempted by
uart_poll_out.
Refactored uart_poll_out implementation to be common for interrupt
driven API and asynchronous API. In both APIs active state is detected
by evaluating state of ENDTX and TXSTOPPED events. If anyone is set it
means that new transfer can be started.
Patch is fixing existing issues:
- potential bytes dropping with flow control enabled
- busywaiting for ENDTX (asynchronous API) - poor performance
- potential bytes dropping during preemption
- potential uart_tx returning -EBUSY when interrupted poll_out
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
In order to be in line with other DT_INST macros in zephyr code base,
swap the arguments order in following macro definitions:
*ST_STM32_DT_PINCTRL
*ST_STM32_DT_INST_PINCTRL
Update the users accordingly.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Current set of helpers provided for STM32 pinctrl devicetree are
using device instance as input.
In order to prepare for next version that will take node identifier
as input, change existing set of macros using _INST_ namespace.
Additionally rename NODE_ID_FROM_PINCTRL to
ST_STM32_DT_INST_NODE_ID_FROM_PINCTRL.
Finally update existing macros users to this new name scheme.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add const modifier for hal instances, clock devices pointer, and module
base address in npcx drivers to prevent driver functions change them
unexpectedly.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Make sure remap is disabled when not requested.
This should have no impact on current cases but is important
when dynamic pin configuration will be used.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace all calls to the assert macro that comes from libc by calls to
__ASSERT_NO_MSG(). This is usefull as the former might be different
depending on the libc used and the later can be customized to reduce
flash footprint.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
This CL adds more comments for each macro functions used for device tree
file for better explanations. It also changes all hex values in soc.c to
lower case.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
On stm32f1 series, device pinctrl configuration could be modified
thanks to remapping capability.
Remapping allows to provide alternate pinctrl configuration to a
peripheral device and applies to all impacted pins.
So, specifically for stm32f1 series, apply remapping when required
before proceeding with pin configuration.
Additionally, because remapping is defined individually for each pin,
apply a function on pinctrl configuration to check remapping setting
coherency accorss pins.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This enables support for the confgure and config_get functions in
the UART API, allowing users to change baudrate, parity, stop bits,
data bits and flow control in runtime.
Signed-off-by: Jesper Derander <jesper.derander@endian.se>
Reset rx byte counters when hw timer/counter is disabled.
Fixes issue where disabling and re-enabling async uart rx can produce
"UART_RX_RDY" events with invalid data when power management is used.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Fixed 'line length exceeds 80 columns' warning by shortening the clock
controller device name from NPCX_CLOCK_CONTROL_NAME to
NPCX_CLK_CTRL_NAME.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add support for `CONFIG_UART_ASYNC_API` to the uart_rtt driver.
As RTT provides no mechanism for knowing when new data has arrived,
the reception commands all return errors.
This fixes hard faults when asynchronous calls are made on the uart_rtt
driver, in addition to providing a small level of functionality.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Instantiate RTT UART instances from devicetree nodes instead of from
Kconfig symbols. While RTT is implemented using software, not hardware,
it is emulating a hardware device, and thus should be configured through
devicetree. This allows the simulated UART device to be selected via
devicetree aliases and chosen nodes.
The following devicetree snippet will instantiate RTT channels 0 and 2
as UART devices.
```
/ {
rtt0: rtt_terminal {
compatible = "segger,rtt-uart";
label = "rtt_terminal";
status = "okay";
};
rtt2: rtt_secondary {
compatible = "segger,rtt-uart";
label = "rtt_app_specific";
status = "okay";
};
};
```
Fixes the RTT portion of #10621.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
These are all the case that coccinelle cannot find as they are inside
macro declarations.
Fixed via:
git grep -rlz -E "\(struct device \*" |
xargs -0 sed -i 's/(struct device/(const struct device/g'
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This CL configures the UART wake-up event triggered from a falling edge
(START condition) on CR_SIN pin. It also includes:
1. Introduce wui_maps property in yaml file to present relationship
between Wake-Up Input (WUI) and UART device.
2. Implement wake-up mechanism by MIWU api functions.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
-Wimplicit-fallthrough=2 requires a fallthrough comment or a compiler
to tells gcc that this happens intentionally.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Remove the macros CLOCK_ID_PRFX2 and CLOCK_ID_PRFX and replace them with
_CONCAT from common.h.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Added support for hardware flow control in EFM32 UART driver.
Signed-off-by: Timo Dammes <timo.dammes@lemonbeat.com>
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Add IUART driver based on MCUX SDK. This driver is used to provide
serial console support on i.MX8M Mini SoC.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
There is nothing wrong with instance numbers and they are
recommended for use whenever possible, but this is an API
design problem because it's not always possible to get nodes
by instance number; in some cases, drivers need to get node
identifiers from node labels, for example.
Change these APIs (which are not yet in any Zephyr release)
to take node IDs instead of instance IDs.
Fixes: #26984
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When uart_configure support was added uart_config_get was not
implemented. Move the 'struct uart_config' to uart_mcux_data lets us
save the uart_config settings and easily return it in
uart_mcux_config_get.
Fixes: #27420
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add example how to use gnome-terminal when launching a new
terminal for attaching the UART.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
uart_rx_enable might be called after reception is stopped by lack
of buffers with flow control enabled. In that case there is a couple
of bytes kept in the HW FIFO. When HW TIMER is used for byte counting,
it is using RXDRDY event to count bytes. RXDRDY event is generated when
byte is received in RXD. RXD is the head of HW FIFO. When DMA ends and
ENDRX event is generated, transmitter still transmits until RTS line
goes high and transmitter reacts to it and stops transmitting. First
byte received after ENDRX lands in RXD (and generates RXDRDY event),
next by goes to RXD+1 (does not generate RXRDY event).
RXDRDY event after ENDRX is counted by the TIMER. If TIMER is reset
before restarting RX this byte is lost in the calculation. Because of
that byte counters cannot be reset before enabling RX thus move to
initialization. It applies only to HW counting but to keep it consistent
resetting was removed for both modes.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The USART_IntGet() function seems to return masked interrupts in the
function uart_gecko_irq_tx_ready() where it should return only
non-masked interrupts. Using USART_IntGetEnabled() fixes this issue.
This issue was discovered when using the mcumgr UART backend in the
uart_mcumgr_isr() function.
Signed-off-by: Steven Lemaire <steven.lemaire@zii.aero>
The EFR32MG21 uses a different kind of GPIO routing for peripherals.
It is based on the GPIO registers and no longer peripherals' registers.
Signed-off-by: Steven Lemaire <steven.lemaire@zii.aero>
Removed potential race condition between uart being disabled and
rx_buf_rsp call.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Added detection of uart_rx_buf_rsp call which happend to late when
uart is already disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This set of functions seem to be there just because of historical
reasons, stemming from Kbuild. They are non-obvious and prone to errors,
so remove them in favor of the `_ifdef()` ones with an explicit
`CONFIG_` condition.
Script used:
git grep -l _if_kconfig | xargs sed -E -i
"s/_if_kconfig\(\s*(\w*)/_ifdef(CONFIG_\U\1\E \1/g"
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When `CONFIG_UART_ASYNC_API` is enabled, cleanup any pending synchronous
receptions at initialization time. Pending receptions are present when
this driver is used with the default mcuboot application.
When `CONFIG_UART_ASYNC_API` is not enabled, RX is always enabled by
this driver. As mcuboot does not use the async API, and does not cleanup
the UART driver before jumping to the next application, that application
boots with RX still enabled. This results in a 500uA increase in current
consumption.
Fixes#26555
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Per the nrf9160 datasheet, UARTE must be disabled prior to configuring
PSEL.TXD, PSEL.RXD, PSEL.CTS, and/or PSEL.RTS. This also ensures that
any prior running code, such as a bootloader, which leaves the UART
enabled will not prevent the Zephyr application from changing the
configuration.
Make a similar change also to the uart_nrf_uart.c driver for the
nRF5 series.
Fixes 27080
Signed-off-by: Pete Skeggs <peter.skeggs@nordicsemi.no>
After switching nSIM to 16550 UART model & driver there is no users
for ARC-NSIM UART. So remove it entirely.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
This gets a little complicated as the driver could be
using PCI-E MMIO, MMIO specified by DTS, or I/O ports.
This driver doesn't use struct uart_device_config any
more.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
PCI devices on 64 bit systems can be mapped anywhere, not just in the
lower 4G of memory. Remove pointer size assumptions.
Also this removes the use of a struct uart_device_config to store the
(runtime) BAR address. That struct has other stuff in it, and the
only thing we need is the single MMIO address. It's also REALLY
confusing to have two "devconf" fields in the device storing values of
the same struct type, some fields of which are used from one of them
but some from the other!
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The STOPTX task cannot be triggered directly in the function that
disables TX interrupt because this task stops the UART transmitter
immediately, even if it is in the middle of shifting out a byte.
Instead, this task needs to be triggered in the interrupt handler,
when the end of transmission is signaled.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add Nuvoton numicro series UART support, currently supports
only poll mode.
UART0 clock and pincontrol are directly configured, will be
replace when clock and gpio support is added.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Convert the present initialization code into initialization macros.
Since both the uart and the usart peripheral is implemented, two sets
of initialization macros are necessary.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Modified order of reported events on rx disable to match API
description: first RX_RDY and then RX_BUF_RELEASED.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
So far, when rx_disable was called then received data was discarded.
This is currently not according to the API but it is needed if
rx_disabled is called due to out of band information about end of
packet.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
So far, when rx_disable was called then received data was discarded.
This is currently not according to the API but it is needed if
rx_disabled is called due to out of band information about end of
packet.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
- Change default CPU Clock to 240MHz
(PLL is activated)
- I2C, UART will use sysclk from clock driver
- esp32_enable_peripheral replaced by
clock_control_on
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Extends the fix in commit 2175675199 to
all other mcux serial drivers. They were incorrectly checking if the
transmit buffer was empty when they should have been checking if the
transmission is complete.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use "kLPUART_TransmissionCompleteFlag" instead of
"kLPUART_TxDataRegEmptyFlag" to check if the tx transmition is finished.
The "kLPUART_TxDataRegEmptyFlag" would give a wrong result
even if the transmition isn't over.
Signed-off-by: Andy Liu <andy@madmachine.io>
Removed flow control configuration from Kconfig and updated samples
to use device tree for that.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Cleaned up flow control configuration. Added support for using only
cts or only rts.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Cleaned up flow control configuration. Added support for using only
cts or only rts.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Replace individual device instance definitions with the macro that
expands to the equivalent change.
F='struct device DEVICE_NAME_GET'
git grep -l "$F" \
| xargs sed -i -r \
-e "s@$F"'\(([^)]*)\);@DEVICE_DECLARE(\1);@'
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This is a follow-up to commit cf7dd4981f.
When disabling RX, it is necessary to clear the RXSTARTED event after
the ENDRX_STARTRX shortcut is deactivated, as the event might already
have been generated at this point. If the event is not cleared and
the disabling of RX is done from the user handler called in the context
of the ENDRX interrupt, a spurious UART_RX_BUF_REQUEST event will be
generated (although RX is already disabled) for which a corresponding
call to uart_rx_buf_rsp() would fail, as the second buffer is already
set. Depending on the application implementation, this can result in
other unexpected problems.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There does not seem to be a simple way to express the fact that UART1
can be initialized later at the POST_KERNEL level. The existing code
is wrong in the sense that it always initializes DT instance 1 later,
instead of doing it for UART1 (which may not be instance 1).
In addition, UART instances on other platforms are
also initialized at the PRE_KERNEL_1 level regardless of the instance
index, so let's do the same on this platform for consistency.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The power configuration is dependent on which UART is physically used.
In order to allow DT_INST_FOREACH_STATUS_OKAY() to iterate through
instances without the assumption that index 0 corresponds to UART0
(which would be incorrect in the case when only UART1 is enabled),
we need to check the base address to identify which UART is being dealt
with.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
When the loop that tries to obtain the lock in poll_out() finishes
because of hitting the max number of trials (what normally should
never happen), force the lock to be taken instead of just giving up
with sending the data. The latter approach that was in use so far
could not deal with a situation when some thread was aborted while
keeping the lock. Other threads would then have no chance to send
anything with poll_out() until it was called from an ISR.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When PCIe is enabled for UART, the port address is probed during
initialization and is written back into the device config struct.
However, the device config struct is supposed to be const and
read only. This results in page faults when MMU is enabled as
the struct cannot be written into. So fix this by storing port
address in device data struct if a particular UART instance is
of PCIE.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The init function returns successful even if the first
configuration function call fails. This may leave
a non-usable UART to be discoverable with
device_get_binding() which will definitely result
in lots of head scratching. So change the init function
to return properly.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The existing uart driver ns16550 did not have ISR locking that
effected IO APIC working in fixed delivery mode in SMP system
x86_64. This commit adds ISR locking mechanism using spinlock
for the interrupt related services.
The CONFIG_IPM_CONSOLE_STACK_SIZE is increased to lift
limitation of stack size experienced in IPM driver test with
this spinlock impelentation.
Fixes#23026
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add infineon XMC4 series UART support. Driver supports
only poll mode using XMCLib.
Out of 4 available UART's on SoC, only UART1 is confgired
by default in UART mode until GPIO & pinctrl support.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Swap this out and make the status a parameter.
Leave a couple of cases of DT_NODE_HAS_COMPAT().
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
These are redundantly checking a node's status twice.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The conversion in 9b096f40b6 left out a
few tidbits that were not converted properly. Complete the conversion
properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert to using DT_INST_LABEL() in the dma driver and convert dma users
to use the DMA property macros to get the dma controller name. We make
the assumption in the drivers that there is a single DMA controller
instance.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Changing more of DT_* prefixed macros that refer to instances to use
DT_INST macros in GPIO, I2C and UART drivers.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert the driver to use the new dt macros. As part of this change we
remove a bunch of defines that happened in dts_fixup.h that didn't
belong there. Some of these should be converted to devicetree
properties at some point.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options for UART instances.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Although it is not clearly specified in the UART API, this function
is supposed to return 0 when the TX interrupt is disabled, regardless
of whether anything could fit into the TX buffer or not (this can be
concluded from looking at implementations of several samples and tests
present in the tree, also almost all UART drivers are implemented this
way).
The problem in the uart_nrfx_uarte driver case is that the flag that
allows generation of the TX interrupt is not cleared directly in the
uart_irq_tx_disable() function but this clearing is deferred to the
end of the current transmission, in case one is in progress, and hence
it is done in the interrupt handler. Consequently, when the interrupt
handler is not entered between calls to uart_irq_tx_disable() and
uart_irq_tx_ready() (e.g. when both functions are called in a loop
executed in the interrupt context), the latter may return an invalid
value.
Fix this problem by additionally checking if the TX interrupt was
requested to be disabled, not only if it is already disabled in
hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-uart binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver was extended so that the tests/drivers/uart/uart_basic_api
test case now passes. The following modifications were made for the
following items of the test case:
* test_uart_configure
* test_uart_config_get
The driver was missing the support to re-configure the UART at run-time
as well as to obtain the current configuration at run-time via the
.configure and .config_get hooks provided within the UART driver API.
For the flow control setting, bit (mask) definitions were added for the
Modem Control Register. Both the configuration get and set functions
come with auxiliary functions that convert configuration register bit
masks to the UART driver API's enumeration types and vice versa.
For run-time configurability, the device's data struct is required un-
conditionally, previously, it was only available whenever interrupt-
driven mode was enabled. Consequently, the device initialization was
simplified to a single call of the DEVICE_AND_API_INIT macro, as the
existance of the device's data struct is now no longer conditional.
* test_uart_fifo_fill
For the user callback function of the test case to receive the initial
'Ready to TX' indication upon which the TX FIFO is filled, it is
necessary that uart_xlnx_ps_irq_tx_enable also sets the TX FIFO empty
bit in the Interrupt Enable Register. Consequently, the same modifi-
cation applies to the irq_tx_disable function.
* test_uart_fifo_read
During inital device configuration, the RX FIFO interrupt trigger
level has to be set to 1 byte for now, as the test case doesn't poll
the incoming data in a while()-loop, therefore, it misses the CR/LF
if more than one character is in the RX FIFO at the time of the
interrupt and neither CR nor LF is the first character.
Whenever the state of an interrupt is checked by the user callback
function (uart_xlnx_ps_irq_tx_ready, uart_xlnx_ps_irq_rx_ready),
the corresponding bits are cleared in the Interrupt Status Register,
re-enabling interrupts generated by the corresponding source.
Tested on QEMU (R5, A9) and actual Zynq7000 hardware.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Added the SERIAL_SUPPORT_INTERRUPT feature flag to the driver's
configuration file. This flag was missing, although the driver
supports interrupt-driven operation.
Interrupt support is required for testcases using the UART_PIPE
feature on the upcoming Cortex-A9 targets (QEMU/Zynq-7000).
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Fix for the UART_XLNX_PS_IRQ_CONF_FUNC macro, which wraps IRQ_CONNECT
into a function for each device instance. This macro had device
instance #0 hardcoded at one point.
Interrupt support is required for test cases using the UART_PIPE
feature on the upcoming Cortex-A9 targets (QEMU/Zynq-7000).
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
In some cases (eg at high baud rate, no HW flow control, and when BLE
radio/ints running) data could be lost between when enough characters
have been RX'd to fill the DMA buffer and when the ENDRX event was
fired, where the the STARTRX task is invoked to start filling the next
buffer (which is set up earlier, but I think will not be filled until
STARTRX).
To fix this, the SHORT is enabled between ENDRX and STARTRX whenever the
'next' buffer is available, so that STARTRX is invoked automatically and
subsequent chars go into the next buffer via EasyDMA.
To make this work properly, uarte_nrfx_isr_async() now handles the ENDRX
event _before_ the STARTRX event.
There was also an issue in rx_timeout() where the received character
count (rx_total_byte_count) could be incremented greater than the actual
buffer size. This arises from rx_total_byte_count value coming from the
counting the RXDRDY events (either by PPI/timer counter or counting the
RXDRDY ints themselves) and so if chars are received in the rx_timeout()
(or before ENDRX is handled) the rx_timeout() could increment rx_offset
past the length of the buffer. This could result the remaining 'len'
being calculated incorrectly (an underflow due to unsigned - signed ,
where signed > unsigned).
To fix this, we now store the lengths of the buffers and don't invoke
the UART_RX_RDY callback when the buffers are full; its handled by
ENDRX.
(Also note that the buffer size should be available via the RXD.MAXCNT
register on the nrf, but this register is not exposed through the nrfx
HAL and is also double buffered, so it seemed clearer to just track the
buffer lengths explicitly here in the driver).
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
for fixup
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
When we build this driver with CONFIG_UART_ASYNC_API enabled we get the
following build error:
uart_sam0.c: In function 'uart_sam0_init':
uart_sam0.c:558:35: error: redefinition of 'dev_data'
558 | struct uart_sam0_dev_data *const dev_data = DEV_DATA(dev);
uart_sam0.c:498:35: note: previous definition of 'dev_data' was here
498 | struct uart_sam0_dev_data *const dev_data = DEV_DATA(dev);
Fix this be removnig the duplicate at line 558.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Avoid entering an infinite loop when configuring the the NXP Kinetis
LPUART IRQ.
Fixes 9a65318a5b.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Reworked usart_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The UART driver for samd0 was is missing the .configure and
.config_get functionality expected from api for serial driver.
This commit fixes this by providing basic configuration
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make I2C and SPI drivers for nRF SoCs no longer dependent on Kconfig
options that enable instances (i.e. I2C_x and SPI_x). Now these drivers
enable hardware instances when corresponding nodes in devicetree are
enabled (have status "okay").
For I2C, SPI, and UART drivers, instead of using Kconfig dependencies
to prevent enabling of hardware instances that cannot be used together
(e.g. SPIM1 and TWIM1), a file that signals invalid configurations with
build assertions is added to compilation.
Also dependencies on HAS_HW_NRF_* options are removed from Kconfigs
of I2C, SPI, and UART drivers, as for hidden options that activate
proper type of driver such dependencies are not actually helpful.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a k_timeout_t type, and use it everywhere that kernel API
functions were accepting a millisecond timeout argument. Instead of
forcing milliseconds everywhere (which are often not integrally
representable as system ticks), do the conversion to ticks at the
point where the timeout is created. This avoids an extra unit
conversion in some application code, and allows us to express the
timeout in units other than milliseconds to achieve greater precision.
The existing K_MSEC() et. al. macros now return initializers for a
k_timeout_t.
The K_NO_WAIT and K_FOREVER constants have now become k_timeout_t
values, which means they cannot be operated on as integers.
Applications which have their own APIs that need to inspect these
vs. user-provided timeouts can now use a K_TIMEOUT_EQ() predicate to
test for equality.
Timer drivers, which receive an integer tick count in ther
z_clock_set_timeout() functions, now use the integer-valued
K_TICKS_FOREVER constant instead of K_FOREVER.
For the initial release, to preserve source compatibility, a
CONFIG_LEGACY_TIMEOUT_API kconfig is provided. When true, the
k_timeout_t will remain a compatible 32 bit value that will work with
any legacy Zephyr application.
Some subsystems present timeout (or timeout-like) values to their own
users as APIs that would re-use the kernel's own constants and
conventions. These will require some minor design work to adapt to
the new scheme (in most cases just using k_timeout_t directly in their
own API), and they have not been changed in this patch, instead
selecting CONFIG_LEGACY_TIMEOUT_API via kconfig. These subsystems
include: CAN Bus, the Microbit display driver, I2S, LoRa modem
drivers, the UART Async API, Video hardware drivers, the console
subsystem, and the network buffer abstraction.
k_sleep() now takes a k_timeout_t argument, with a k_msleep() variant
provided that works identically to the original API.
Most of the changes here are just type/configuration management and
documentation, but there are logic changes in mempool, where a loop
that used a timeout numerically has been reworked using a new
z_timeout_end_calc() predicate. Also in queue.c, a (when POLL was
enabled) a similar loop was needlessly used to try to retry the
k_poll() call after a spurious failure. But k_poll() does not fail
spuriously, so the loop was removed.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Kernel timeouts have always been a 32 bit integer despite the
existence of generation macros, and existing code has been
inconsistent about using them. Upcoming commits are going to make the
timeout arguments opaque, so fix things up to be rigorously correct.
Changes include:
+ Adding a K_TIMEOUT_EQ() macro for code that needs to compare timeout
values for equality (e.g. with K_FOREVER or K_NO_WAIT).
+ Adding a k_msleep() synonym for k_sleep() which can continue to take
integral arguments as k_sleep() moves away to timeout arguments.
+ Pervasively using the K_MSEC(), K_SECONDS(), et. al. macros to
generate timeout arguments.
+ Removing the usage of K_NO_WAIT as the final argument to
K_THREAD_DEFINE(). This is just a count of milliseconds and we need
to use a zero.
This patch include no logic changes and should not affect generated
code at all.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Use of macros such as SYS_POWER_STATE_SLEEP_2 needs to be guarded by
making sure CONFIG_SYS_POWER_SLEEP_STATES is defined.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Convert older DT_INST_ macro use in litex drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in atmel sam0 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree nodes and associated headers for
defined uarts on the stm32g0 and stm32g07x 8x parts.
Tested with uart on stm32g071rb disco board with usart3 going to stlink.
Using shell.
Signed-off-by: Kieran Levin <ktl@frame.work>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 defines to something
non-DT prefixed. This way we know which defines are one's we generate
and which ones are driver created. It should be easy enough to replace
these INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 define with DTS generated
one macros once esp32 has interrupt controller support in DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in silab drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in stellaris drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a dependency on the UART resource in the TI Power module,
reconfigure the UART upon CPU exiting standby, and add support
for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The shared irq support isn't needed in this driver. We just need to
deal with the fact that some SoCs have only a single interrupt line and
some have three interrupts. We can just ifdef that based on
DT_NUM_IRQS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A txcnt of zero prevents transmission, as transmit requires the number
of entries in the transmit fifo to be strictly less than the txcnt
value. Set the default to 1.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
uart_configure verification handler was missing what would cause a crash
if called from a user thread.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Added return -ENOTSUP in uart_rx_enable() if RX pin is disabled.
Fixed power management call where TASKRX was started even though
RX pin was disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Extended nrf_uart driver to support TX only.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a fixed clock to the qemu-virt-a53.dtsi to match how the musca dts
files work so we get the clock DT info in the same way in the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
After RX is disabled during receiving, some bytes are received to
internal fifo. To not interfere with further transactions fifo has to be
flushed.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Convert driver to use DT_INST_ defines.
In the process, we've removed all UART/USART/LPUART code in
device instanciation code which had no impact.
Since all uart/usart/lpuart nodes declare compatibility with
st,stm32uart, DT_INST_X_ST_STM32_UART_FOO could be used.
Removed DT_UART fixup macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In the DT_INST conversion we introduced a typo bug of accessing port0
instead of port1 in the IRQ config function.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update device data with the activated configuration, so that it
will be remembered for follow up configuration get requests.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Change to code to use the automatically generated DT_INST_*
defines and remove the now unneeded configs and fixups.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
The sole purpose of init options has been to enable hardware flow
control on NS16750 when asked. Use the proper DTS tags for this.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Added locking for TX transfers between async and polling API.
Added safety counters for checking if transmission finished.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add locking between async and polling tx transfers.
Add safety counters while waiting for transmission to finish.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Convert driver to fully use DT_INST_ defines. Currently IRQs are not
generated from DTS on esp32 so we create #defines for what they should
look like. Convert the IRQ defines to match DT_INST style so if/when
we have that info in DTS it will look the same.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update hal_nordic's revision, so that NRFX_ASSERT uses __ASSERT_NO_MSG
directly, not through the assert macro that comes from from libc,
as the definition of the latter might be different when some specific
libc version is used, and this could generate troubles.
Replace also uses of assert() with __ASSERT_NO_MSG() in nrfx driver
shims that use this macro without including the corresponding header
file (i.e. that implicitly rely on assert.h being included from
nrfx_glue.h, which is no longer the case).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The `irq_update` UART API function must always return 1 according to
the API documentations.
This commit fixes the `irq_update` API function to unconditionally
return `1`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The `irq_update` UART API function must always return 1 according to
the API documentations.
This commit fixes the `irq_update` API function to unconditionally
return '1'.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Since driver is shared with other devices, it must be enabled
conditionally based on the number of instances. This avoid show
invalid options for devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
SAMV71 uses same driver of SAME70 and this enables the feature. Since
driver is shared with other devices, it must be enabled conditionally
based on the number of instances. This avoid show invalid options for
devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit fixes the multiple SERCOM interrupt handling for the SAM
D5x and E5x devices by replacing the obsolete device tree symbol with
the new `DT_INST` symbol.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
When building with LLVM we get the following error:
uart_stm32.c:272:9: error: implicit conversion from enumeration type
'enum uart_config_parity' to different enumeration type
'enum uart_config_flow_control' [-Werror,-Wenum-conversion]
return UART_CFG_PARITY_NONE;
~~~~~~ ^~~~~~~~~~~~~~~~~~~~
We shouldn't be mixing parity and flow control enum's. Use
UART_CFG_FLOW_CTRL_NONE instead or UART_CFG_PARITY_NONE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Current implementation directly passes timeout value to workqueue/timer
which results in assertion or instant timeout in case when K_FOREVER is
passed. This fix ensures that no timer or workqueue is called with
K_FOREVER.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Use signed values for timeout in UART asynchronous API, to be consistent
with timeout type in timer and workqueue values.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Extended nrf_uarte driver to support TX only UARTE instances.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Silicon Labs EFM32GG11B SoCs have more USART ports than
currently supported by the driver. Driver expanded with
support for USART4 and USART5.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
The PrimeCell UART (PL011) IP can use one single combined/shared
interrupt line instead than different IRQ lines for TX/RX/Err/... This
is the most common configuration supported in the Linux world but not
currently supported in Zephyr. QEMU emulates a PL011 UART with a single
interrupt line as well.
To support this configuration we have to hookup the PL011 driver with a
shared IRQ driver and add two new configuration options when the shared
IRQ line is used.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
There is only one possible command, so just use if instead of switch
to avoid several MISRA-C violations and also avoid set dev_data wrongly
unused when UART_NS16550_DLF_ENABLED is defined.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Commit 68a235932f changed this driver to
not use hard-coded options. The problem was that these options were
never being set. This commit just set an initial value that can be
changed later.
Fix 68a235932f
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The NS16550 UART driver is currently hard-coded as 8-n-1
with no flow control. The baud rate is set by what is in DTS.
This commit moves away from hard-coded and strictly DTS to
configurable using the UART configure API. Requires commit #bcb807.
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
The UART configure API was added to uart.h and this commit
implements the initial framework for the configure API for
the ns16550 uart. This includes the configure() and config_get()
functions and uart device configuration structures of the uart
configure API for the ns16550.
Note this commit does not resolve the pre-existing hard-coded
8-n-1 implementation.
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These were unintentionally omitted. We don't expose callback
registration or callback response APIs for security reasons.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Nrfx_uarte uses a hardware timer/counter to count received bytes.
Keeping this timer enabled increases power consumption for some SoCs.
This change disables the timer when an inactive power state is set.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Refactors the mcux lpsci driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux uart driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpuart driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
calling UARTE power management with DEVICE_PM_SUSPEND_STATE
then DEVICE_PM_OFF_STATE causes a deadlock in while loop.
It waits for an event witch never comes
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
Cleanup around COND_CODE_1 usage and replacing with
IF_ENABLED if applicable.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Uses the generated device tree macros, DT_NXP_LPC_USART_USART_*, in the
mcux flexcomm driver and removes the now unused dts fixups from the
lpc54xxx and lpc55xxx socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the lpc usart shim driver to more accurately reflect the
flexcomm hardware IP and to prepare for instantiating it on an SoC
outside the LPC family.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add clearing error event to UART and UARTE drivers.
Without it driver goes into infinite interrupt loop.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
This patch tests the return code when calling clock_control_get_rate
and completes the issue #20503 seen on watchdog
[Coverity CID :205655]
Fixes#20503
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There is possibility that endrx interrupt will be triggered in the
middle of timer interrupt responsible for UARTE timeout, this
patch handles this case.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Update calls to nrfx HAL functions to reflect API changes introduced in
nrfx 2.0.0. All these functions are now called with the first parameter
pointing to the structure of registers of the relevant peripheral.
Also a few functions got renamed:
- nrf_gpiote_int_is_enabled to nrf_gpiote_int_enable_check
- nrf_gpiote_event_is_set to nrf_gpiote_event_check
- nrf_rng_event_get to nrf_rng_event_check
- nrf_rng_int_get to nrf_rng_int_enable_check
- nrf_rtc_event_pending to nrf_rtc_event_check
- nrf_rtc_int_is_enabled to nrf_rtc_int_enable_check
- nrf_timer_cc_read to nrf_timer_cc_get
- nrf_timer_cc_write to nrf_timer_cc_set
Default configuration values were removed from nrfx_config files,
so the drivers pwm_nrfx and spi_nrfx_spis no longer can use those.
Function nrfx_pwm_init() now takes one more parameter - context pointer
that is passed to the event handler, not used in the pwm_nrfx driver.
HALs for UART and UARTE now allow configuration of the parity type
and the number of stop bits, for SoCs that provide the corresponding
registers.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Several macros were documented as deprecated but lacked the
infrastructure to produce deprecation warnings. Add the deprecation
marker, and fix the in-tree references to the deprecated spellings.
Note that one non-deprecated macro should have been deprecated, and
is, referring to a newly added line control bit.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The SAME5x/SAMD5x MCUs share their SERCOM peripherals with the
samd2x and saml1x MCUs with only few registers changed.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added in commit f9efca4b4f ("boards: riscv32: add LiteX VexRiscV
board"), then never used.
Found with a script.
Also change UART_LITEUART from a 'menuconfig' symbol to a 'config'
symbol, as it's no longer followed by symbols that depend on it
(UART_LITEUART_PORT_0 should have been a plain 'config' too).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In some applications where power management is used, it is not expected
that the GPIO pins of the UARTE is reconfigured upon power state change.
Added a Kconfig option to disable the UARTE driver management of GPIOs.
It defaults to y in order to not affect current behavior unless the user
configures it specifically.
Signed-off-by: Dennis Wildmark <dennis.wildmark@assaabloy.com>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the base address from the device tree for instance 0 (LPUART0)
instead of hardcoding the address using the NXP MCUX HAL definition.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The driver is not specific to 32bit ARM family. For example it is
currently used by the QEMU ARM64 virt machine.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This commit switches from using device tree automatically
generated address-based defines to the instance id-based ones.
Without this change it is not be possible to re-use the driver
on boards where the device is located at different location
than 0xe0001800.
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Currently both uart_stm32_irq_tx_complete() and
uart_stm32_irq_tx_ready() return the TXE flag. However
uart_irq_tx_complete() should really return the TC flag to output true
"Transmit Complete" status.
Signed-off-by: Tommy Vestermark <tovsurf@vestermark.dk>
The driver fails to compile when CONFIG_UART_INTERRUPT_DRIVEN=n. This is
due to a nested ifdef on CONFIG_UART_INTERRUPT_DRIVEN that is excluding
pieces of code unrelated to the uart interrupts management.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The PL011 driver is not specific to the cortex_m arch and the driver
does not really use anything from the cmsis header file. Remove it.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The new SDK version 2.6.3 for LPC55S69 changes how CLOCK_GetFreq works.
Change to use CLOCK_GetFlexCommClkFreq which can work on both the old
and new SDK.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the device tree to assign the correct peripheral clock to each
UART/USART/LEUART. Previously, the clock identifier was determined
through the sequence number of the instantiated UART. This meant
configuring all UARTs when only one of the later UARTs was required.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
We need to change the order of inclusions in
uart_mcux_lpuart.c, to avoid build errors. This
is required since the driver structures contain
a field named DATA, which is also a macro defined
in the linker script.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
nrf52840 and nrf9160 have possible configuration of two stop bits
for UART and UARTE, this commit adds handling of it to driver.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
A commit that organizes the soc.h header of NXP SoCs:
- removing redundant inclusions of sys/util.h
- removing inclusions of device.h and kernel_includes.h
- including the auto-generated DTS board header
- including the fsl_common.h header
- fixing minor style issues
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The semi-automated API changes weren't checkpatch aware. Fix up
whitespace warnings that snuck into the previous patches. Really this
should be squashed, but that's somewhat difficult given the structure
of the series.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These calls are buildable on common sanitycheck platforms, but are not
invoked at runtime in any tests accessible to CI. The changes are
mostly mechanical, so the risk is low, but this commit is separated
from the main API change to allow for more careful review.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
- dts updated for UART1/2
- Additional check added to _INIT macro to configure flow control mode
- Additional check added to _INIT macro to set CTS/RTS gpios values
- Additional check added for gpio config
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
- Fixes#3981
- Implement UART Polling functions
- Implement UART Interrupt APIs
- Remove dependency on esp32_rom_uart_xxx functions
- Update Device tree with UART addresses and pin config
- Update ESP32 UART KConfig
Notes about implementation:
- Interrupts now defined as a local macros, and should be removed
later on, when interrupts for esp32 are supported in dts
- Threshold interrupts are used for TX/RX
- Reseting FIFOs using _RST bit will corrupt FIFO of UART2 when used for
UART1 and vice-versa, so a generic way is used for all three UARTs
- Old Silicon rev is not supported
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Utilize the multi-level irq infrastructure and replace custom handling
for PLIC on riscv-privilege SoCs. The old code offset IRQs in drivers
and various places with RISCV_MAX_GENERIC_IRQ. Instead utilize Zephyr's
encoded IRQ and replace offsets in drivers with the IRQ define from DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure pins before enabling and after disabling UARTE through
power management functions.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Ensure that two routines won't interfere with eachother.
In current situation there is possibility that ENDRX will be called
during rx_timeout routine or vice-versa which will result in wrong
offset and length passed to user.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Due to longer than expected user callback handling, rx byte counting
got out of sync with real values. It leads to incorrect values
reported to user. This fix adds sync point at the end of buffer.
When using hardware rx counting this issue should not occur.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
In some hardware,e.g. ARC HS Development kit,the
peripheral space of ns16550 only allowes WORD
access, byte acess will raise bus error.
This commit adds support for this case
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
