Zephyr version 3.4 changed the SPI context structure and macros
which broke the logic in the MEC172x SPI driver configuration API.
This was not detected by CI due to no tests for this driver are in
the tree. The driver now behaves like most other SPI drivers requiring
a different configuration structure pointer to be passed if any item
in the configuration changes.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Initial version of Infineon CAT1 SPI Driver supporting synchronous
and asynchronous data transfer API
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
When doing a TX-only SPI operation, the RX not empty flag will never get
set, thus this will just hang forever.
Found/tested on STM32L462 trying to drive some WS2812 RGB LEDs.
Signed-off-by: David Lamparter <equinox@diac24.net>
Add fundamental feature support for RP2040 PIO SPI peripherals.
This commit implements synchronous transfer with 8-bit MSB
format. Using PIO allows any GPIO pins to be assigned the roles
of CS, CLK, MOSI, and MISO.
Optional features not implemented yet:
- Interrupt based transfer
- DMA transfer
- Slave mode
- Varying word size
- 3-wire SPI support
- LSB-first
Updated in response to review comments.
Further updates from second round of review.
Rename spi_pico_pio.c source to match zephyr/MAINTAINERS.yml
Remove unnecessary initialization code.
Resolve merge conflicts
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Check the TXC flag instead of EOT for the case of endless
transactions (TSIZE = 0), which in this case is always as
the stm32 SPI driver doesn't set TSIZE.
Signed-off-by: Daniel Gaston Ochoa <dgastonochoa@gmail.com>
CONFIG_NOCACHE_MEMORY is a valid way of declaring buffers in
nocache regions. Consider them valid in the stm32 SPI driver
nocache check. Also, don't check NULL buffers as the SPI
interface states that such buffers will result in sending
zeroes.
Signed-off-by: Daniel Gaston Ochoa <dgastonochoa@gmail.com>
This is a follow-up to commit fa609e5844.
This driver implements SPI slave operations only and cannot be used
without the corresponding Kconfig option enabled.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Following #56576, the `cs` field in `struct spi_config` is of type
`struct spi_cs_control` instead of a pointer to the same type.
This PR updated the driver to use `spi_cs_is_gpio()` helper to
check if SPI CS is controlled using a GPIO.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Removes the shadow variable found by -Wshadow. The value of this
variable is the same throughout the for loop, so there is no
need to assign it again for each iteration.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Pin state after SPI deinitialization is based on pinctrl configuration.
On the other hand, CPOL is set during runtime. When the SPI instance
is disabled GPIO takes control over SCK and drives it to state set
by pinctrl driver. This might causes an invalid SCK state
when the transaction is configured with CPOL (Clock Polarity).
To address this issue, a patch was introduced to the SPI driver.
Now, when a SPI instance is configured with CPOL,
the driver is setting in the runtime the correct state of the SCK pin.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Pin state after SPIM deinitialization is based on pinctrl configuration.
On the other hand, CPOL is set during runtime. With the introduction
of the power-optimized SPIM driver, it disables the peripheral instance
once the transfer is completed.
As a result, the GPIO takes control over the SCK pin and drives it
based on pinctrl configuration which causes an invalid SCK state
when the transaction is configured with CPOL (Clock Polarity).
To address this issue, a patch was introduced to the SPIM driver.
Now, when a SPIM instance is configured with CPOL,
the driver is setting in the runtime the correct state of the SCK pin.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
ESP32 SoC refactoring added new SOC_SERIES definition,
which was missed by #60183. This fixes it.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
SPI driver is current working for common SPI devices.
However, addressable LED like WS2812 requires MOSI line to be
default LOW during initialization. This PR adds such option.
This has no effect on common SPI operation.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Add option to use (by defining the `wake-gpios` devicetree properties)
an additional signal line between SPI master and SPI slave that allows
the latter to stay in low-power state and wake up only when a transfer
is to occur.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Refactor the function to make the execution flow in transceive()
clearer. In particular, return error codes directly, not through
spi_context_complete() which is unnecessary in this case.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
DMA only works with non-cached memory regions in H7. Check them
and return an error if they don't match this condition.
Signed-off-by: Daniel Gaston Ochoa <dgastonochoa@gmail.com>
This is a follow-up to commit 4c20403629.
CONTAINER_OF() cannot be used to obtain the device pointer from its
data pointer as this data is not contained in the device structure.
Instead, use a dedicated member in the device data structure to store
the device pointer.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
- use CONFIG_HAS_HW_NRF_* symbols consistently in nRF multi-instance
drivers when creating particular driver instances
- remove unnecessary hidden Kconfig options that indicated the type of
peripheral to be used by a given instance (e.g. SPI, SPIM, or SPIS)
and enabled proper nrfx driver instance; instead, use one option per
peripheral type and include the corresponding shim driver flavor into
compilation basing on that option (not the one that enables the nrfx
driver as it was incorrectly done so far in some cases)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This CL attempts to implement npcx's flash driver instead of the
original one (npcx spi driver plus spi_nor flash driver).
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The MCUX DMA controller only supports a single data_size
for a DMA transfer, not separate ones for source and
dest. An older version of the DMA driver used
dest_data_size as the DMA transfer size, but the
current one uses MIN(dest/source) as the trasnfer
size, which breaks case when SPI wants to do 2-byte
transfers.
Signed-off-by: Mike J. Chen <mjchen@google.com>
The `spi_mcux_transceive` had 2 return calls when the
`CONFIG_SPI_MCUX_LPSPI_DMA` flag was active. The first return would be
called and the later was unreachable. With the fix, now the return calls
are mutually exclusive. Also, the `transceive` call is not compiled with
the `CONFIG_SPI_MCUX_LPSPI_DMA` flag is active.
Fixes#59533
Signed-off-by: Dipak Shetty <dipak.shetty@zeiss.com>
The eSPI, I2C, and SPI emulators use devicetree macros to build an array
of devices on the virtual bus. Currently, they will add device nodes that
are not status-okay. This leads to linker errors because the respective
device drivers would not have instantiated device structs for these
nodes --assuming the driver was even compiled. This can be frustrating
if nodes need to be disabled for debugging or configuration purposes.
Update the bus emulators to only consider status-okay nodes by changing
the macros used to iterate over bus devices.
Signed-off-by: Tristan Honscheid <honscheid@google.com>
Fix for bug:
https://github.com/zephyrproject-rtos/zephyr/issues/59575
The dma version of the version of the driver can
invoke multiple intermediate dma transfers, like
when the spi_buf_set count is greater than one.
However, there is a bug where chip select is not kept
asserted for all intermediate dma transfers required
to process the entire spi_buf_set.
Signed-off-by: Mike J. Chen <mjchen@google.com>
Replace the timeout for a SPI transceive in slave mode for STM32 DMA
operations with a K_FOREVER. Being an SPI slave means we do not
know when the transaction will start, hence it does not make sense
to have a timeout in such a case.
This will resolve issue #60000.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
The `SPI_EMUL_INIT(n)` macro used to instantiate SPI bus emulators
builds an array of SPI devices attached to the bus, but always checks
instance #0 of the bus and not `n`. This makes multiple instances of an
emulated SPI bus unusable and popualtes them all with bus 0's devices.
Change the `0` to `n`, which matches how the I2C bus emulator does it.
Signed-off-by: Tristan Honscheid <honscheid@google.com>
This adds a few line use zephyr_syscall_header() to include
headers containing syscall function prototypes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Found EMSDP board SPI-FLASH sample broke after adding DFSS
into spi_dw. Found wrong interrput mask resulting in false
interrupt enabled. Now fixed it to fit both DFSS and DW.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
Introduce DesignWare ARC Data Fusion IP Subsystem(DFSS) SPI
driver for ARC boards, i.e. EMSDP, which uses DW SPI to controll
SPI-Flash and DFSS SPI to connect external devices. Both drivers
share most source code, but DFSS uses ARC auxiliary registers.
Move FIFO depth setting to device tree.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
Commit 246393e830
("drivers: spi: spi_nrfx_spim: Remove nrf_frequency_t handling")'
introduced two changes, one of them is removing the function
get_nrf_spim_frequency with a strange justification.
This change breaks support for peripherals written in a common way,
where the maximum frequency is set to the maximum supported
by the peripheral, not the controller, see shields for example.
On the occasion of bringing it back, the original function was
refactored to be easier to read and understand.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add driver for OpenTitan SPI host.
Tested and verified single SPI full duplex on opentitan_earlgrey in
Verilator.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
Rather than the rings, which weren't shared between userspace and kernel
space in Zephyr like they are in Linux with io_uring, use atomic mpsc
queues for submission and completion queues.
Most importantly this removes a potential head of line blocker in the
submission queue as the sqe would be held until a task is completed.
As additional bonuses this avoids some additional locks and restrictions
about what can be submitted and where. It also removes the need for
two executors as all chains/transactions are done concurrently.
Lastly this opens up the possibility for a common pool of sqe's to
allocate from potentially saving lots of memory.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Added device tree bindings and implementaion for setting the
spi controllers chip select setup and hold time settings.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
The nrfx SPI driver depends on semaphores, which require multithreading
support to be enabled.
Signed-off-by: Eivind Jølsgard <eivind.jolsgard@nordicsemi.no>
Make use of positive status values in the DMA callback to pass
info to the DMA client after a successful DMA operation.
A completed DMA transfer uses the status 0 while a reached
water mark uses the status 1.
Signed-off-by: Cyril Fougeray <cyril.fougeray@worldcoin.org>
Word size setting limited any SPI transaction to the frame
size. In addition to making the SPI inefficient this
broke drivers that set the word size. It appears that most
drivers use a one byte (8) size for this setting.
This change respects what I think is the intended use of
the word size setting. That is to set the length of
each element in a tx/rx buffer struct.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
With new nrfx release SPIM driver stores frequency as a `uint32_t`
type representing frequency in `Hz` in its configuration structure.
Additionally `NRFX_SPIM_PIN_NOT_USED` has been removed,
`NRF_SPIM_PIN_NOT_CONNECTED` symbol is used instead.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
When dma is enabled, spi_xmc4xxx_transcieve_dma() needs to disable the
isr used by spi_xmc4xxx_transceive(). Renable the isr at the
end of spi_xmc4xxx_transceive_dma() instead of in spi_xmc4xxx_transceive().
Doing this in latter function will fail compilation when interrupt
support is enabled but dma is disabled.
This is regression from 8494b6413a
but was only caught when xmc47_relax_kit was added which tested this
scenario in tests/drivers/spi/spi_loopback.
Fixes#57494
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
When using gpio chip select the clock line seems to get stuck low after
some transactions. When attempting to use other SPI_CSR registers
the peripheral fails to work as expected.
Always using SPI_CSR[0] when using gpio chip selects resolves the issue.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
spi_context_get_next_buf must not divide `len` by `dfs` because, in SPI,
buffer lengths are given in units of data (in this case, 16 bits), not in
bytes.
Signed-off-by: Daniel Gaston Ochoa <dgastonochoa@gmail.com>
Following #56576, the `cs` field in `struct spi_config` is of type
`struct spi_cs_control` instead of a pointer to the same type.
`spi_xec_qmspi_ldma.c:qmspi_xec_init` tries assigning `NULL` to the
`.cs` field through a designated initializer, which causes a compilation
error.
This PR simply removes the `.cs = NULL` line. The designated initializer
will automatically zeroize the underlying GPIO pin info, which should
have the same effect that setting the pointer to NULL did previously.
Signed-off-by: Tristan Honscheid <honscheid@google.com>
Add spi_cs_is_gpio(_dt) helpers to check whether SPI CS is controlled by
GPIO or not. This both improves code readability and isolates SPI
internals.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
As of today it is not possible to use SPI dt-spec macros in C++,
something known and documented. The main reason is because `cs` property
is initialized using a compound literal, something not supported in C++.
This PR takes another approach, that is to not make `cs` a pointer but a
struct member. This way, we can perform a regular initialization, at the
cost of using extra memory for unused delay/pin/flags if `cs` is not
used.
Fixes#56572
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The rvm32m1 platform always uses pinctrl, there's no need to keep
extra macrology around pinctrl. Also updated driver's Kconfig to `select
PINCTRL`.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The MCUX platform always uses pinctrl, there's no need to keep extra
macrology around pinctrl. Also updated driver's Kconfig options to
`select PINCTRL` (note that some already did).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
When using a dummy buffer on the RX side, do not
increment the destination memory buffer address.
This issue was uncovered when running the SPI
loopback test.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The spi-sam0 driver does not initialize DMA parameters when the MCLK
peripheral is defined in the microcontroller header file. Fix it by
copying the initialization code from the non-MCLK case.
Signed-off-by: Brandon Del Bel <delbel@umn.edu>
This adds the SPI driver for the Renesas SmartBond(tm) DA1469x MCU family.
The driver only supports controller mode. All four SPI modes are supported.
Note that the lowest supported speed is 2285714Hz.
Requesting speeds higher than 16MHz, will result in a 16MHz SCLK.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Zephyr SPI driver model for full-duplex operation assumes
data will be transmitted and received during each clock period.
The QMSPI driver for the XEC family also supported dual and
quad I/O use cases which are inherently half-duplex. To
support dual/quad the driver incorrectly processed spi buffers
as all transmit buffers first then all receive buffers. This
worked if only the SPI driver was used. It did not work with
the Zephyr flash SPI NOR driver which assumes SPI drivers
follow the SPI driver model. This commit implements a QMSPI
driver that follows the Zephyr SPI driver model resulting in
a slightly smaller driver. Dual/quad SPI transactions are
supported if the experimental SPI extended mode Zephyr
configuration flag is enabled. We also remove the QMSPI full duplex
driver added previously to support the flash SPI NOR driver.
Added board to spi loop-back test and spi_flash sample.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
There have an extral TBE interrupt event though we have cleared the
SPI_CTL1_TBEIE bit. To cover this situation, add a on_going check
before enter exchange function.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Implements the SPI RTIO API. Refactors many of the internal transfer
functions to work on simple types to allow for both the RTIO and existing
SPI API functions to co-exist.
Removes the unneeded shift_master specialization. Either a polling or DMA
transfer flow is used when used with RTIO as all operations are normalized.
When SPI_RTIO is enabled the spi_transceive blocking call translates
the request into an RTIO transaction placed in the queue of transactions
the device is meant to do.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Provides a macro and submit API for SPI drivers to support RTIO.
A copy function enables compatibility with the existing blocking API
and very easily the existing async API as well.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
This commit fixes the word size configuration issue
described in #54746 by considering the data frame size
when trasmitting in case the configuration is applied.
It also fixes an heap corruption problem when using
SPI DMA with a buffer that is not multiple of 32 bits
in lenght and GDMA instance in initialization.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The number of available EasyDMA MAXCNT bits is now defined per-instance
in Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
A MACRO argument naming mismatch causes a bug when trying to use DMA.
Fix the MACRO argument and conditional DMA configuration.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Uninitialized sam spinlocks were causing an error if the stack
happens to have 'thread_cpu' memory set to something other than 0.
Signed-off-by: Yuval Peress <peress@google.com>
Currently the driver only support software controlled CS
defined by cs-gpios property.
This commit enables the possibility of using dedicated CS
by setting the pins on pinctrl and omitting the cs-gpios
property.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Change the preprocessor identifier from CONFIG_SOC_ESP32C3 to
SOC_GDMA_SUPPORTED so it can include ESP32S3 in GDMA routines.
Remove hardcoded values from hal calls to use dma_host instead.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Since PINCTRL and pinctrl-0 is now required, there's no point in doing
extra validation at driver level. Modify the macro to just check that
sleep state is present when needed, since it was the only remaining
assertion that was not covered. Renamed the macro to make it more clear
what it does: NRF_DT_CHECK_NODE_HAS_PINCTRL_SLEEP
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The fast tx/rx/txrx functions will leave the SPI bus in an
inoperable state if interrupted, potentially spinning forever waiting on
some data. Wrapping these operations in what amounts to a critical section
using spin locks to avoid the issue.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add code that acts accordingly when a transaction does not complete
in the expected time. It makes sure that the transaction is aborted
so that no unexpected interrupt occurs afterwards and it also cleans
up after that abort so that the driver can handle further requests.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When estimating the time that a given SPI transfer will take, whole
buffer sets for TX and RX need to be taken into account, not only their
first parts. Correct `spi_context_wait_for_completion()` accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit makes the peripheral-id property optional and removes it's
usage from the Gecko SPI driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
Add missing "default y" to the Kconfig option so that it gets selected
automatically when a matching devicetree node is enabled.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Clean up occurrences of "#if IS_ENABLED(CONFIG_FOO)" an replace
with classical "#if defined(CONFIG_FOO)".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Config NOCACHE_MEMORY depend on ARCH_HAS_NOCACHE_MEMORY_SUPPORT. Enable
ARCH_HAS_NOCACHE_MEMORY_SUPPORT for Cortex-R52 to run NXP S32Z/E with
nocache attibute.
Enable nocache in each driver use it.
Signed-off-by: Duong Vu Nam <duong.vunam@nxp.com>
When configuring an LPSPI module for a new device with different baud rate,
the module needs to be disabled for the baud rate change to take effect.
This adds the necessary call to LPSPI_Enable before initializing the
module.
Fixes#51177
Signed-off-by: Jonas Otto <jonas@jonasotto.com>
This casts the char * buffers to void * before giving them to the
LOG_DBG function to fix a warning at runtime.
Signed-off-by: Gaël PORTAY <gael.portay@gmail.com>
Return correctly the number of received bytes for a
spi_transceive on a STM32 SPI slave.
Fixes#52216
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
For larger transfers DMA can be used enabling other tasks
to continue running. A threshold of 32 byte transfers
is about right and is defined threshold value for using DMA.
This does not currently support multiple SPI transactions changing
chip select with DMA (though the hardware supports this) currently.
Instead opting for the simpler first change of enabling one shot
DMA SPI transfers for those where the size warrants it.
Adds the loopback binding option to enable the spi_loopback test.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Microchip MEC172x QMSPI expanded its clock divider register
field from 8 to 16 bits. QMSPI source clock is on the fast
peripheral domain therefore get the frequency from the clock
control driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Change automated searching for files using "IRQ_CONNECT()" API not
including <zephyr/irq.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add MEC172x full duplex qmspi driver version to support full
duplex transfers as expected by the Zephyr spi driver model.
On every spi clock we transmit one bit and receive one bit.
This driver will work with Zephyr SPI NOR driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
If the thread that submits data over spi is interrupted by a higher
priority thread while pushing data to the tx fifo the hardware pushes
data to spi and frees up space in the fifo. In this case more than
8 Bytes are written to the tx fifo and bytes in the rx fifo get lost
before they are collected in the rx while loop.
To avoid this, the tx loop is exited after a maximum of 8 bytes and the
rx loop will run until it collected all bytes from the rx fifo.
Signed-off-by: Gerhard Jörges <joerges@metratec.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 qmspi. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
This commit is the adaptation of the stm32 SPI driver with DMA
transfer for the stm32u5 soc.
Use the DT_HAS_COMPAT_STATUS_OKAY(st_stm32h7_spi)
also valid for the stm32U5 serie.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
As of today <zephyr/zephyr.h> is 100% equivalent to <zephyr/kernel.h>.
This patch proposes to then include <zephyr/kernel.h> instead of
<zephyr/zephyr.h> since it is more clear that you are including the
Kernel APIs and (probably) nothing else. <zephyr/zephyr.h> sounds like a
catch-all header that may be confusing. Most applications need to
include a bunch of other things to compile, e.g. driver headers or
subsystem headers like BT, logging, etc.
The idea of a catch-all header in Zephyr is probably not feasible
anyway. Reason is that Zephyr is not a library, like it could be for
example `libpython`. Zephyr provides many utilities nowadays: a kernel,
drivers, subsystems, etc and things will likely grow. A catch-all header
would be massive, difficult to keep up-to-date. It is also likely that
an application will only build a small subset. Note that subsystem-level
headers may use a catch-all approach to make things easier, though.
NOTE: This patch is **NOT** removing the header, just removing its usage
in-tree. I'd advocate for its deprecation (add a #warning on it), but I
understand many people will have concerns.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
west.yml: update hal_espressif to use latest v4.4.1 updates.
This change needs to be insync with esp32c3 timer changes, otherwise it
breaks it.
drivers: timer: update esp32c3 systimer to meet API changes.
Systimer API was refactored in hal v4.4.1, which
requires updates in esp32C3 systimer. Timer behavior is maintained
as is.
mcpwm: add v4.4.1 include reference, which was refactored as well.
driver: spi: esp32: update internal structs to meet API changes.
cmake: updated esp32 board to use HAL_ prefix as from west blobs
requirement.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
The commit 4c20403629 updated the
`spi_psoc6_transceive` function signature but forgot to update its
usages.
This commit updates the `spi_psoc6_transceive` function invocations
to properly provide the callback and user data parameters.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit updates the SiFive SPI driver to reflect the
`spi_context_complete` and `spi_context_lock` function signature
changes introduced in the commit
4c20403629.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit updates the Microchip MSS QSPI SPI driver to reflect the
`spi_context_complete` and `spi_context_lock` function signature
changes introduced in the commit
4c20403629.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit updates the LiteSPI SPI driver to reflect the
`spi_context_complete` function signature change introduced in the
commit 4c20403629.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit updates the Gecko SPI driver to reflect the
`spi_context_complete` function signature change introduced in the
commit 4c20403629.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit updates the GD32 SPI driver to reflect the
`spi_context_complete` and `spi_context_lock` function signature
changes introduced in the commit
4c20403629.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Adds a new spi_transcieve_cb API which enables asynchronous
SPI transactions with callback notification.
The exist spi_transcieve_async API remains and uses the new
spi_transcieve_cb API to provide a k_poll_signal notifier.
The driver API changes to provide a callback and userdata
parameter to async transcieve. All drivers in the tree
have been updated to the change.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Many device pointers are initialized at compile and never changed. This
means that the device pointer can be constified (immutable).
Automated using:
```
perl -i -pe 's/const struct device \*(?!const)(.*)= DEVICE/const struct
device *const $1= DEVICE/g' **/*.c
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add fundamental feature support for PL022 SPI peripheral.
This commit implements synchronous transfer with 8bit-MSB format.
Optional functions are not currently implemented yet.
- interrupt based transfer is not implemented yet.
- DMA transfer is not implemented yet.
- Slave mode is not implemented yet.
- Currently support only 8-bit data transfer.
Hardware limitation:
- LSB-first format is not supported by hardware.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
This is a bug fix. A pointer to the spi configuration is not saved when
the spi driver is configured for slave operation and it can lead to
runtime errors.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
In order to work on a clock speed higher than 20 MHz, IO MUX is required.
Co-authored-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Signed-off-by: XiNGRZ Chan <hi@xingrz.me>
In the continuation of the previous commit, replace _OPT_ by _DOMAIN_
in macros relating to this feature.
hen, adapt drivers and tests to this new wording.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds optional device tree property to specify a default character
to clock out when the TX buffer pointer is NULL. If the property is
not set the existing behavior (default char of 0x00) is used.
I verified the expected behavior using an i.MX RT685 board and
logic analyzer that the def-char character is transmitted when
TX buffer pointer is NULL.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
MISRA C:2012 Rule 14.4 (The controlling expression of an if statement
and the controlling expression of an iteration-statement shall have
essentially Boolean type.)
Use `do { ... } while (false)' instead of `do { ... } while (0)'.
Use comparisons with zero instead of implicitly testing integers.
The commit is a subset of the original auditable-branch commit:
5d02614e34a86b549c7707d3d9f0984bc3a5f22a
Signed-off-by: Simon Hein <SHein@baumer.com>
Update spi drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
Rework the <BUS>_emul_register calls to not pass the name param. The
name param is only used for logging and we can get it from the
struct <BUS>_emul instead.
Signed-off-by: Kumar Gala <galak@kernel.org>
Having a per-instance init function makes code cluttered and hard to
read. Just create a per-instance IRQ connect function (required to
resolve IRQ_CONNECT parameters at compile time).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using NRFX_SPI(S|M)_INSTANCE helper so that peripheral address from
Devicetree is used. We should not rely on HAL for hardware description
but Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The maximum transfer buffer length is SoC specific, not instance
specific. This patch defines MAX_BUF_LEN at driver level in a SoC
specific manner instead of using HAL values that are instance specific
but that always take the same value depending on the SoC.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The maximum transfer chunk length is SoC specific, not instance
specific. This patch defines MAX_CHUNK_LEN at driver level in a SoC
specific manner instead of using HAL values that are instance specific
but that always take the same value depending on the SoC.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
