The ace15 description has incorrect number of SSP instances
described. Correct number should be 3.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
The tgph description has incorrect number of SSP instances
described. Correct number should be 3.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Enable serial interface on i.MX8ULP.
This also includes a SHA update for hal_nxp which
pulls in the following commits relevant to Zephyr:
* 3366f234ed47 build: hal_nxp: add TPM counter support
* 6544455fcf46 Compile in PXP driver if LVGL is set to use
PXP.
* 31463a848bcd devices: MIMX8UD7: add definition for
LPUART_RX_TX_IRQS
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Configure the 'soft-off' power state for manual selection only in the
DTS for Intel ADSP ACE 1.5 MTPM and ACE 2.0 LNL platforms.
Changes include:
- Setting 'min-residency-us' to 0 to indicate that the 'soft-off' state
is not intended for automatic selection by the power management
policy.
- Adding a 'status' property set to "disabled" to prevent the power
management policy from using this state during its decision process.
The 'soft-off' state remains available for manual selection by calling
`pm_state_force`. This change ensures that the state can still be used
when explicitly requested by the system or application, providing
flexibility for power management operations.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
This commit enables pinctrl on i.MX8ULP. This includes:
1) Adding `pinctrl_soc.h` header file.
2) Adding DTS node for IOMUXC1, which is one of the
IPs responsible for managing the 8ULP pads.
3) Adding .dtsi with pin definitions. For now, only
the LPUART7 pads are added to this file because this
is going to be the only consummer for now.
4) Modifying the `pinctrl_imx.c` driver to work for 8ULP.
5) Enabling the `CONFIG_HAS_MCUX_IOMUXC`, which is a
dependency of `CONFIG_PINCTRL_IMX`.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Enable clock control for i.MX8ULP. This consists of:
1) Adding a PCC node in the DTS
2) Adding a header file containing the definitions
of the clocks used by the peripherals to be enabled.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This will update host dma copy aligmnet as with current
high value in some cases it was not possible to fully
empty the buffer
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Remove the Audio Link Hub (ALH) nodes from the ACE 2.0 LNL DTS file.
This patch cleans up the Device Tree Source by removing the individual
ALH stream/FIFO nodes. The ALH hardware is not present in the ACE 2.0
architecture, and these nodes are therefore not applicable.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
This patch reorders the power domain definitions for the Intel ADSP ACE
2.0 LNL (Lunarlake) platform in the Device Tree Source (DTS).
Changes include:
- Removing the definitions for io2_domain, io3_domain, and ml1_domain,
which are no longer present in the ACE 2.0 LNL configuration.
- Renaming and reassigning bit positions to existing power domains to
reflect the updated power management architecture.
The reordering ensures that the DTS reflects the current power domain
architecture of the ACE 2.0 LNL platform, facilitating accurate power
management within the SoC.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Changing the power domain from 'hst_domain' to 'io0_domain' for the HDA
DMA link in/out nodes. This aligns the power domain assignments with the
actual hardware configuration and ensures that the power management
subsystem can accurately manage the power states of these interfaces.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
This patch reorders the power domain node definitions in the ACE 1.5
Meteorlake DTS file to improve readability and facilitate comparison with
the documentation.
Changes include:
- Reordering power domain nodes by their bit positions.
- No changes to the bit positions themselves; they remain as originally
defined.
This reordering does not affect the functionality but makes the DTS file
more maintainable and easier to cross-reference with the hardware
specification.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit enables the IRQSTEER interrupt controller
on NXP's XTENSA-based i.MX8QM and i.MX8QXP.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
SOC_ESP32_NET is now SOC_ESP32_APPCPU, following espressif's
naming convention in the same manner as ESP32S3 app cpu.
SOC_ESP32_APPCU is now a subset of SOC_SERIES_ESP32.
This commit also changes the necessary files, samples and tests
for bisect purposes.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
This commit introduces a new interrupt controller driver used
for NXP's IRQ_STEER IP.
Apart from introducing the driver itself, this commit contains
the following changes:
1) Switch i.MX8MP to using the XTENSA core interrupt
controller instead of the dummy irqsteer one.
* this is required because the binding for the
irqsteer driver is no longer a dummy one
(since it's being used by the irqsteer driver).
As such, to avoid having problems, switch to
using another dummy binding.
2) Modify the irqsteer dummy binding such that it
serves the IRQ_STEER driver's needs.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add dummy interrupt id until we can support UART interuppt
on i.MX8MP in order to fix compilation warnings.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
DW watchdog driver is not used on ACE,
Intel ADSP watchdog driver will be used in DTS when ready to use
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
This commit introduces all changes necessary for utilizing
the serial interface on i.MX8QM/QXP.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Since the LPUART peripheral DTS binding requires the
"interrupts" property be specified even if it's not going
to be used for now we need to add a dummy interrupt controller
node to make that possible. Logically speaking, this dummy
interrupt controller should be used by peripherals which
can assert interrupts directly routed to the DSP.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This commit enables clock control on the i.MX8QM and QXP boards.
This is achieved through the following changes:
1) The "reg" property is no longer marked as required
for the "nxp,imx-ccm" binding. This is necessary because
in the case of i.MX8QM and i.MX8QXP the clock management
is done through the SCFW, hence there's no need to access
CCM's MMIO space (not that you could anyways).
2) The DTS now contains a scu_mu node. This node refers
to the MU instance used by the DSP to communicate with
the SCFW.
3) The CCM driver needs to support the LPUART clocks
(which will be the only IP that's supported for now)
and needs to perform an initialization so that the
NXP HAL driver knows which MU to use to communicate
with the SCFW.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Fix the following compilation warning:
```
Warning (unit_address_format): /memory@0xb0000000: \
unit name should not have leading "0x"
```
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Remove nxp,imx-mu-rev2 compatible. This IP block is the same as the
nxp,imx-mu device, and should be handled by the same compatible
Instead, use CONFIG_HAS_MCUX to determine which HAL APIs should be used
to interact with the messaging unit IP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Updates Ethernet PHY devicetree bindings to be more consistent with
Linux by using the standard `reg` property for the PHY address instead
of a custom `address` property. As a result, MDIO controller bindings
now require standard `#address-cells` and `#size-cells` properties.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Update the descriptions for the various CAN devicetree timing properties
specified in Time Quanta (TQ) to make it clear that these, if present, are
only used for the initial timing parameters.
Deprecate the (Re-)Synchronization Jump Width (SJW) devicetree properties
for both arbitration and data phase timing as these are now only used in
combination with the other TQ-based CAN timing properties, which are all
deprecated.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add `mdio_read_c45()`/`mdio_write_c45()` APIs for Clause 45 access
and remove the `protocol` MDIO binding property so that MDIO bus
controller can support more than one protocol.
A new MDIO header is introduced with generic opcodes, MMD and
registers addresses, to be used by MDIO and PHY drivers.
Existing MDIO drivers that support both Clause 22 and Clause 45
access are migrated to the new APIs.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
LP/HP RING OSC clocks were replaced by the ACE IPLL clock.
If needed IPLL can be configured to work as low power clock. But right
now ACE uses only WOVCRO and IPLL (configured to work as HP RING OSC
clock).
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
LP/HP RING OSC clocks were replaced by the ACE IPLL clock.
If needed IPLL can be configured to work as low power clock. But right
now ACE uses only WOVCRO and IPLL (configured to work as HP RING OSC
clock).
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
The ACE family platforms do not have LP/HP RING OSC clocks. They were
replaced by the ACE IP integrated PLL clock. Selecting LP or HP in
CLKCTL will result in enabling IPLL.
Clock can supply frequencies for both replaced clocks, default frequency
equals to 393.2 MHz.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
The ACE family platforms do not have LP/HP RING OSC clocks. They were
replaced by the ACE IP integrated PLL clock. Selecting LP or HP in
CLKCTL will result in enabling IPLL.
Clock can supply frequencies for both replaced clocks, default frequency
equals to 393.2 MHz.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
The zdsp.basicmath needs a bit more ROM space to run.
So enlarge the indicated ROM size to accommodate that.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add missing definitions for ALH DAIs. Keep the same FIXME
reminder in the comments we have for ACE1.5 that explains
the background of these definitions.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
To properly setup L1 exit timing this patch will use buffer interrupt
for HOST DMA and wait for Host HDA to actually start
First interrupt will clear all others.
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
This adds SoC and board configs to support the dc233c core
that is available on QEMU. This core has more features than
sample_controller, such as MMU support.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
