Devicetree specification v0.4, Section 2.3.1:
"The compatible string should consist only of lowercase letters, digits
and dashes, and should start with a letter."
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This state is never used in practice, even if handled by the PM
subsystem hooks. Shutdown-like states are always invoked manually, so
they don't need to be described in DT.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The `cpu-power-states` property needs to be defined at SoC dts files,
since it's a property of the SoC, not board.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 8 (CCU8)
module. There are two CCU8 nodes with each one having four slices.
Each slice has two output channels.
Unlike CCU4, this module can generate complementary high-side/low-side
signals for each output channel. A variable dead time can be added
during the off to on transitions to make sure that the
high-side/low-side signals are not on at the same time.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 4 (CCU4)
module. There are four CCU4 with each one having four channels
Thus it's possible to have up to 16 pwm output signals. The output of
each channel can only be connected to a specific port/pin. The possible
connection and gpio configurations are defined using pinctrl.
The CCU4 module also has a capture mode. Capture support will be added
in the future.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Add mailbox and interrupt-controller nodes used for
inter-process communication.
Add also the dt binding for the interrupt-controller.
For now, this is used just to fix some compile errors,
since the mailbox requires an interrupt-controller.
For DSP, we have a direct interrupt line to the core.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Introduces support for SoC-specific input-edge-detect configuration to
the CC13/26xx pinctrl driver.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Added a driver for the DFRobot A01NYUB distance sensor. This sensor
sends its readings via UART at 9600 baud. This driver uses interrupts
to read the data from the sensor.
Signed-off-by: Oliver King <oliver.king@steadconnect.com>
Add support for flash NOR memory devices on a NXP S32 QSPI bus. The
driver uses a fixed LUT configuration assuming a default standard page
size and erase types, and allows to select between multiple read/program
instructions/modes. It is also possible to read the flash device
characteristics from the device at run-time as long as the memory is
JESD216 compatible, providing more flexibility.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The NXP S32 QSPI controller acts as an interface to up to two serial
flash memory devices, each with up to eight bidirectional data lines,
depending on the platform. It is based on a LUT enginee to interface
through commands with different memory types including flash NOR and
Hyperram.
This patch adds support for the QSPI in S32K344 which supports a single
memory device (side A) with up to four bidirectional data lines and SDR
only. Nevertheless, the memory controller is implemented flexible enough
to be extended to support more feature-rich QSPI blocks.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
This commit aligns TWIM shim to utilize memory-region property.
The memory-region is not required property that enables user
to specify placement of dma buffers in memory region.
It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Add initial version of Infineon CAT1 counter driver
Add initial version of binding file for Infineon
Add counters to psco6 dtsi
Add external trigger pin that runs counter
Signed-off-by: Pavlo Havrylyuk <pavlo.havrylyuk@infineon.com>
Each PSCI interface versions have different DT compatible strings
like arm,psci-0.2, arm,psci-1.1 and so on. However, the same driver
can be used for all the versions by adding #define DT_COMPAT for
required version and #undef DT_COMPAT for default version.
Add support for PSCI cold reset, warm reset and cpu-on function IDs.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
Signed-off-by: Navinkumar Balabakthan <navinkumar.balabakthan@intel.com>
If the optional hardware reset line is available, this change
will use that reset line to assert the uart module and bring
it out of reset state to use.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
This is Intel's proprietary IP which controls individual module
reset signals. During each system driver initialization, these
reset signals will be used to bring module out of reset state.
Signed-off-by: Navinkumar Balabakthan <navinkumar.balabakthan@intel.com>
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
Device tree for Intel SoCFPGA Agilex5 initial bring up. This is the
first version of device tree which enable four cores SMP and basic
drivers that needed by 'hello_world' and 'cli' applications.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
This is Intel's proprietary IP which supply the clock for all the
system peripherals. Clock manager is initialized only one time
during boot up by FSBL (ATF BL2) based on external user settings.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
Introduce dtsi files representing the
current portfolio of chips and modules
based on the:
- flash size
- psram size
- gpio count
- certification status
Update the boards dts files according
to which SOC/SIP they are using.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Introduce dtsi files representing the
current portfolio of chips and modules
based on the followint criteria:
- flash size
- psram size
- gpio count
- certification status
Update the boards dts files according
to which SOC/SIP they are using.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Previously the driver was retrofitted to the kscan api, handling it as a
input device with one row and three columns. With the move to the input
subsystem each input can have its proper input code instead.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
The 'zephyr,memory-region-mpu' property was addede gqas a
convenient way to create and configure MPU regions using information
coming from DT. It has been used a lot since it was introduced so I
guess we can consider it a Zephyr success story ™ .
Unfortunately it has been proved to be a bit limited and with some
important limitations:
1. It was introduced as a property of the compatible
zephyr,memory-region that is used to create linker regions and
sections from DT data. This means that we can actually create MPU
regions only for DT-defined regions and sections.
2. The naming is unfortunate because it is implying that it is used only
for MPU.
3. It is misplaced being in include/zephyr/linker/devicetree_regions.h
and still it has nothing to do with the linker at all.
4. It is exporting a function called LINKER_DT_REGION_MPU that again has
nothing to do with the linker.
Point (1) is also particularly limiting because it is preventing us to
characterize memory regions that are not generated using the
'zephyr,memory-region' compatible, like generic mmio-sram regions.
While we fix all the issues, we also want to extend a bit the range of
usefulness of this property. We are renaming it 'zephyr,memory-attr' and
it is now carrying information about the type of memory the property is
attached to (cacheable, non-cacheable, IO, eXecutable, etc...). The user
can use this property and the DT API coming with it to act on the memory
node it is accompanied by.
We are still providing the DT_MEMORY_ATTR_APPLY() macro that can be used
to create the MPU regions as before, but we are adding also a
DT_MEMORY_ATTR_FOREACH_NODE() macro that can be used to cycle through
the memory nodes and act on those.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
CPU idle states are not board specific. This patch moves Nuvoton idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves NXP idle states
to the core SoC dts files. Board can always tweak some state parameters
(if needed), but the definition belongs to core SoC dts files, same as
e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves Microchip MEC
idle states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves TI idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves STM32 idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves ESP32 idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The NXP Pixel pipeline engine (PXP) is a 2D DMA engine capable of
accelerating display rotation, color space conversion, and limited
2D blending operations. This DMA driver only supports rotation of a
framebuffer, via a set of custom dma_slot values. Only DMA channel 0
is supported or utilized.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Updated the driver to support low power mode.
Introduced "enable-low-power" flag in device tree to
control(on/off) low power mode.
If flag added in DTS, during sleep BBLED will switch off the LEDs.
Otherwise BBLED will continue the configured blinking pattern on LEDs.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Add support for resetting controller at boot, and update FT5336
documentation to indicate that the FT3267 IC is also supported by this
driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for RM67162 MIPI display controller. This controller
is configured to run in MIPI command/DBI mode, driving a 400x392 OLED
display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Only setup DPI input from LCDIF if MODE_VIDEO is set, as this
is the the only case where input from the LCDIF would be required to
drive the display. Do not populate the dpi_config structure unless a
reference the the NXP LCDIF device is provided, since this is the output
device providing DPI data.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fixup support for DCS_LONG_WRITE command in DSI MCUX 2L driver. Since long
DCS commands may benefit from nonblocking I/O, add support for non blocking
transfers to the DSI driver.
This commit also corrects the interrupt number for the RT595, which uses
the DSI_MCUX_2L IP block.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Make DPI mode an optional configuration for the DSI MCUX 2L driver.
DPI mode will only be enabled when the MIPI is attached in video mode,
since this is when DPI formatted packets are expected.
This will enable the DSI driver to also support DBI/command mode, for
displays that use this format.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added dts additions for stm32f105xb cpu which is the same as existing
stm32f105xc with less flash.
Signed-off-by: Mathieu Anquetin <mathieu.anquetin@groupe-cahors.com>
- Add overlay for the esp32s2_saola board to die_temp_polling sample.
- Add aliases for the die_temp_polling sample to esp32s2 dtsi.
Signed-off-by: Hiroki Tada <tada.hiroki@fujitsu.com>
Enabled support for is31fl3733 driver. This driver supports
the full LED API, and enables the following features of the is31fl3733:
- individual LED dimming
- individual LED enable/disable
- bulk writes of LED enabled and dimming states
- global LED current limit
- blanking (via custom API)
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
Add Nuvoton numaker series flash memory controller(FMC) with erase,
read & write features of soc-flash. Also update Nuvoton manifest
to include zephyrproject-rtos/hal_nuvoton#6.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
This CL attempts to implement npcx's flash driver instead of the
original one (npcx spi driver plus spi_nor flash driver).
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add a new pinctrl type to control peripheral modules' specific IO
characteristics such as tri-state, the power supply type selection (3.3V
or 1.8V), and so on. In NPCX series, the corresponding registers/fields
are irregular. This CL wraps these definitions to dt nodes and put them
in pinctrl property if needed.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This driver is built on top of the IVSHMEM doorbell
notification mechanism providing an unified way
to generate inter VM interrupts.
Signed-off-by: Felipe Neves <felipe.neves@linaro.org>
Add the new RCC bindings to the dtsi files.
STM32F373 uses the RCC F1 bindings because the ADC prescaler is the same
on the two series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add two new bindings for STM32F1x and F3x RCC to add the ADC prescaler
specific to these series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
AXP192 is a small and simple power management IC featuring different
LDOs, DCDCs, AINs and also GPIOs. It also offers functionaltiy for
battery management.
This change includes the basic regulator driver functionaltiy for
LDO2-3 and DCDC1-3 as well as the mfd driver layer. Further drivers
for GPIO and ADC will follow.
Drivers have been developed and tested on M5StackCore2, an ESP32-based
board. Support for M5StackCore2 is still in progress.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
GT911 IC uses the INT pin to select the correct I2C address during
reset. However, some boards may not route this pin (or may only support
receiving inputs on it). This results in the I2C address selected by the
GT911 IC being arbitrary based on the state of the (floating) INT pin.
To resolve this, introduce an `alt-addr` property for this device. When
set, the INT pin will not be pulled low. Instead, the I2C address will be
probed at runtime, starting with the devicetree address and falling back to
`alt-addr`.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This patchset is doing three things:
1. It is fixing the bogus algorithm to find the optimal number of
descriptors for a given memory size.
2. It is changing values for VDEV_STATUS_SIZE and
IPC_SERVICE_STATIC_VRINGS_ALIGNMENT to better align to a usual cache
line size.
3. RX/TX VRINGs are now correctly aligned to MEM_ALIGNMENT (and cache
line alignment).
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This patch adds a description section for the pwms property of the PWM
LED child node. This intends to explain how the period field is used by
the led_pwm driver and to help with its configuration.
Reported-by: Scott Worley <scott.worley@microchip.com>
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Convert the GT911 driver to the input subsystem, fix the existing boards
to work in the default config.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Aligns the filename of TI's CC13/26xx system timer peripheral devicetree
binding to its compatible string.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
This adds support for the bosch bmi085 and bmi088. This also includes
support for data sync mode.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
This patch adds support for PWM blink which is found in intel's
PCH hardwares.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Current erroneous usages of dma-channels prop by lpc-dma nodes:
* dma-channels devicetree property should describe the number of
channels supported by the dma controller, not the number of channels
in use.
* LPC55SXX and RTXXX SOCs should be setting dma channels prop at SOC
level, not board level, since it is an SOC property, not a board
property.
* lpc55s28 has 23 channels for dma0, not 20.
* lpc55s28 has 10 channels for dma1, not 0.
* lpc55s69 has 23 channels for dma0, not 20.
* rt5xx has 37 channels for dma1, not 0.
* rt6xx has 33 channels for dma0, not 20.
* rt6xx has 33 channels for dma1, not 0.
Fix all of these issues
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Set the DMA number of otrigs DT property at the SOC level instead of the
board DTS because it is an SOC property and does not change on different
boards.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add I2C target driver used buffer mode. The maximum accessible buffer
is 2044 bytes, the default is 256 bytes.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add basic device tree description fro stm32wba soc series.
This includes Flash/RAM clocks and clock control nodes
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add support of r8a77961 SoC to gen3 series.
Create a dtsi file with a common part for both r8a77951 and r8a77961.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\xmc47_relax_kit board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Adding support for the adafruit can picowbell shield for the
raspberry pi picoi. Also added nodelable for spi0 called 'pico_spi'
as well as an GPIO nexus node 'pico_header'
Signed-off-by: Joseph Yates <joeyatessecond@gmail.com>
This change introduces the "_rtc_timer" suffix for the system tick timer
driver "compatible" property and aligns naming conventions with the
actual CC13/26xx SoC series product policy.
This frees up the "_rtc" namespace to introduce additional APIs based on
the same peripheral in the future (not part of this PR):
rtc: rtc@... {
compatible = "ti,cc13xx-cc26xx-rtc";
...
timer {
compatible = "ti,cc13xx-cc26xx-rtc-timer";
...
};
counter {
compatible = "ti,cc13xx-cc26xx-rtc-counter";
...
};
pps {
compatible = "ti,cc13xx-cc26xx-rtc-pps";
...
};
};
Or alternatively an MFD pattern with similar requirements.
Fixing the namespacing now makes sense standalone as it reduces the
chance of custom drivers being broken in the future.
Redundant extension of the mandatory system clock devicetree node is
replaced with a single `status = "okay"` which seems to be the more
sensible default to avoid user error when defining custom boards.
Knowledgeable users can still override this if really needed.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Removes duplicate code and inconsistencies in the naming of the
cc13xx_cc26xx devicetree and RTC driver hierarchy and alignes it with
the actual TI product series naming hierarchy.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Add SHA256 accelerator support for it8xxx2 series.
This driver passes the following test:
tests/crypto/crypto_hash/
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Changes rshunt-milliohms to rshunt-micro-ohms allowing for current
sensing of greater than 16.4A (1mOhm resistor). This is commonly
set to 100 uOhm for VMU/FMU boards/applications.
Co-authored-by: James Goppert <james.goppert@gmail.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
The different references manuals of the STM32H7 family (RM099, RM0433,
RM0445 and RM0468) states that SDMMC2RTS and STMMC2EN are on bit 9 of
respectively RCC_AHB2RSTR and RCC_AHB2ENR (not on bit 8). Fixes the stm32h7
dts accordingly.
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
Reuse existing MCUX-based shim driver for LPUART that is compatible with
the hardware block in S32K344. DMA is not yet supported.
Use the board's debug connector (P6 / LPUART2) as default console.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
SIUL2 may require multiple interrupt handlers instead of a single one as
currently supported for S32Z/E. This is needed to enable support on
S32K3.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Support pin control for NXP S32K3 devices and enable it by default on
mr_canhubk3 board configuration.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The clock controller is a singleton controller for all the system-level
clocks (XOSC, PLL, CGM, etc) to provide run-time information to the
peripheral device drivers about the module's clocks.
Clock configuration is not yet supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The S32K3 MCUs are 32-bit Arm Cortex-M7-based microcontrollers with a
focus on automotive and industrial applications. The S32K344 features
a lock-step core, internal flash, RAM and TCM with ECC.
Co-authored-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Co-authored-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add a small delay between reading the transport header and reading the
HCI data. Failing to do so on a nRF9160<->nRF52832 link was reliably
resulting in the nRF9160 trying to read data before the nRF52832 had
set up the SPI transaction, resulting in the host reading a buffer full
of 0x00 and having to run the entire read result again.
Transceiving a 10 byte packet takes at least 31uS, while 100 byte
packets are around 150uS (duration of `spi_transceive` call). Waiting
1 tick to eliminate the need for most retransmissions is a valid
tradeoff.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add an option that signifies that the ESP modem may be reset at the same
time as the SoC by an external source. When this is the case, we first
wait for an unsolicited "ready" message from the modem, before
attempting to reset the device. This prevents two initialisation
sequences attempting to run at the same time.
We still want to wait for the complete initialisation sequence to
complete before returning in this case.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This adds support for the TIMER1-4 counter.
Each counter has 24bits and can run on LP_CLK (15-32KHz)
or DIVN clock (32MHz) with prescaler 1-32.
Each counter can have one alarm set.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
The display controller supports software reset and the driver already
implements it. Therefore it's not necessary to require a reset gpio in
device tree.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Remove `clocks` property for fixed-clock binding.
A fixed-clock should not have an input clock, since by
definition it's an always on fixed-rate clock.
Signed-off-by: Moritz Fischer <moritzf@google.com>
This adds a driver for Texas Instruments Cost-Optimized, Ultra-Small,
12-Bit, System-Monitoring ADCs. Currently only TLA2021 is supported,
TLA2022 and TLA2024 may follow based on this driver.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Convert the XPT2046 driver to the input subsystem, change the api,
remove the callback and enable logic.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Usage of 64-bit address constants from devicetree without a
UINT64_C wrapping macro results in the following warning and the
cut-off of the address value:
"warning: integer constant is so large that it is unsigned"
This change extends devicetree API adding few wrappers over the
address constant getters which add ULL size suffix to an
address integer literal when the appearance of 64-bit address
values is possible
Signed-off-by: Alexander Razinkov <alexander.razinkov@syntacore.com>
Add a GPIO based quadrature decoder driver that reports relative axes
movements using the input subsystem.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Adds properties to configure OCTOSPI IO
Manager data lines. That allows to use
any `IOLowPort` and `IOHightPort`.
Note: OSPIM requires additional clock to be enabled.
Please refer to Reference Manual.
Extra clock can be enabled in devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Add Nuvoton numaker series UART support, including interrupt-driven,
also apply pinctrl and clock-control.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add Nuvoton numaker series clock controller support, including:
1. Do system clock initialization in z_arm_platform_init().
2. Support peripheral clock control API equivalent to BSP
CLK_EnableModuleClock()/CLK_SetModuleClock().
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add support for communication with serial ports on native POSIX platform
via UART driver API. Serial port driver supports polling API,
configuration of the serial ports used via devicetree and command line
options, and runtime configuration with `uart_configure`.
Multiple instances of the driver are supported.
Example use and configuration is also demonstrated in the
`samples/drivers/uart/native_tty` sample.
Closes: #56586
Signed-off-by: Marko Sagadin <marko.sagadin42@gmail.com>
Add simple mechanism to load the image from IMR memory. Basically we are
only setting a flag in power off for the next boot to jump to existing
image in IMR.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
The IS31FL3216A is a fun light LED controller. The LED current of each
channel can be set in 256 steps by adjusting the PWM duty cycle through
an I2C interface.
Signed-off-by: Guy Morand <guy.morand@bytesatwork.ch>
Add a minimal driver for the ti lp5569 led controller. The driver supports
multiple instances. Commands on|off|set_brightness are supported.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
Currently, only the presence of a GIC is reflected in the device tree,
and its version must be set separately in each SoC's Kconfig.
This patch adds separate bindings for each GIC version whose presence
in the device tree automatically enables the corresponding Kconfig symbol.
Signed-off-by: Piotr Wojnarowski <pwojnarowski@antmicro.com>
When the GIC driver was originally introduced, it was only used on
Cortex-R SoCs. However, this is not the case anymore. Update the
description to reflect that this driver is not specific to Cortex-R.
Signed-off-by: Piotr Wojnarowski <pwojnarowski@antmicro.com>
Add driver for TCN75A temperature sensor. The following features are
supported:
- TCN75A oneshot mode, which allows single shot conversions with lower
power consumtion
- Resolution selection, up to 12 bit resolution (9 bit default)
- Triggering based on temperatue thresholds. If the TCN75A exits a set
threshold range, the application can be notified via a callback.
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
Add a new pinctrl driver for TI CC32XX SoC. The driver has not been
tested, just implemented following datasheet specs and checked that it
compiles. Consider this as a best-effort driver to remove custom pinmux
code in board files.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This PR adds a custom driver for the ADS1112 ADCs. Unlike ADS1113/4/5
family served by the ADS1x1x driver, the ADS1112 does not use an address
pointer to address config registers. Instead, there is only one writable
register and all i2c writes will set it. The registers resemble the
ADS1119 device, but config bitmap is different, include a distinct data
rate table, gain table, and input multiplexing table. There is also not a
status register to be monitored with the ADS1112, as it uses config bit 7
for the same purpose instead of a separate register.
The driver was tested on hardware using the ADC shell interface. Manual
probing validated the voltages for the MUX_SINGLE configs at datarate 15
in CM_SINGLE. Higher gains were not tested and CM_CONTINUOUS is not
supported in this initial implementation.
The new driver has also been added to the existing ADC test using adc_emul
for completeness.
Origin: original
License: Apache 2.0
Purpose: Adding support for ADS1112 ADCs
Signed-off-by: Jordan Montgomery <jordan.montgomery@getcruise.com>
Move dt files related to SoC family and series to npcx folder. It only
leaves SoC dt file in `dts/arm/nuvoton folder` in case of confusion with
the other Nuvoton SoCs.
The dt files path will be:
dts/arm/nuvoton
|--npcx
| |--npcx7
| | |--npcx7-miwus-wui-map.dtsi
| | |--npcx7-alts-map.dtsi
| | |--.....
| +--npcx9
| | |--npcx9-miwus-wui-map.dtsi
| | |--npcx9-alts-map.dtsi
| | +--.....
| |--npcx-miwus-wui-map.dtsi
| |--npcx-alts-map.dtsi
| |--npcx.dtsi
| |--npcx7.dtsi
| |--npcx9.dtsi
|--npcx7m6fb.dtsi
|--npcx7m6fc.dtsi
|--npcx9m8f.dtsi
+--npcx9m3f.dtsi
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move the two UART nodes so that they are under "soc" rather than "espi",
leave only xec-espi-host-dev nodes there.
The UART device can be used indepdently by the driver uart_mchp_xec.c
and it's normally initialized before before the espi one.
Moving the device node up a level so this does not trigger a false
positive on the build time priority checking.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Restructure the Bosch M_CAN driver backend to use per-instance Message RAM
configuration.
This removes the need for a common, artificial "can" devicetree node for
SoCs with multiple Bosch M_CAN-based CAN controllers and allows for
per-instance configuration of the number of e.g. standard (11-bit) and
extended (29-bit) filter elements.
As part of the restructure, software handling of CAN filter flags was moved
from per-flags bitfields to per-filter bitfields, solving an issue when
using more than 32 standard (11-bit) filter elements or more than 16
extended (29-bit) filter elements.
Fixes: #42030, #53417
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN devicetree binding to use a bosch,mram-cfg property
for specifying the memory layout of the Bosch M_CAN Message RAM. This is
identical to the Linux kernel devicetree binding for Bosch M_CAN IP core
based CAN controllers.
This introduces an offset cell which can be used for controllers with
shared Message RAM between Bosch M_CAN instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The BG95 pin configuration does not internally ever use the reset pin.
Because of this, there is no need to make reset pin mandatory.
Commit removes reset pin dependency [e.g. in case of BG95].
Signed-off-by: Andrei Hutanu <andrei.hutanu.i@gmail.com>
Add a property to the ADC channels which allows the configuration
of the current source pin.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Added Input/Output trigger mux address's as properties
that can be passed into the DMA driver. This is intended
to send INPUTMUX signals into the DMA.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Ports the Jinghua Display JHD1313 LCD (with RGB backlight) driver
to use the new auxdisplay driver interface. This driver is used on
the seeed grove LCD RGB display, and replaces it.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
Removed few VIF properties which are being hardcoded
Updated the script to parse source VIF XML and add information to
the output
Added optional Kconfig option to configure custom source VIF XML path
Cleaned up the code
Signed-off-by: Madhurima Paruchuri <mparuchuri@google.com>
Added intel LPSS DMA interface using dw common to support
usage of internal DMA in LPSS UART, SPI and I2C for
transfer and receive operations.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds the pwrmgr devicetree node. This is a simple binding that holds
only the address of the registers for now.
This patch is part of the OpenTitan watchdog (AON Timer) support patch
series. It is needed to ensure that the watchdog reset functionality
is enabled.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
The OpenTitan power manager is responsible for changing the OpenTitan's
operation to and from low power state. This patch adds a simple binding
for the power manager's config registers.
This is part of the OpenTitan watchdog patch series. The power manager
HWIP block needs to be configured to enable the watchdog reset
functionality in the OpenTitan Verilator simulation.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
Adds the AON Timer device in the OpenTitan Earlgrey device tree.
Adds overlay files to enable the watchdog and set the alias to
`watchdog0`.
Adds the AON timer (watchdog part) to the supported features section
of the OpenTitan documentation.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
The OpenTitan AON Timer is a hardware device that has two features:
the wakeup timer and watchdog timer. This commit series implements the
watchdog feature.
The spec can be found here:
https://opentitan.org/book/hw/ip/aon_timer/index.html
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
Flash address is updated to 0x16000000, i.e. actual location instead of
remapped one. FLASH_BASE_ADDRESS is now set via dts.
Co-authored-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
This selects default flash controller in device tree.
Co-authored-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
This adds support for the USB interface for the
Renesas Smartbond DA1469x device family.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
RT1040 removes LPSPI3, and refers to the peripheral called LPSPI4 on
other RT devices as LPSPI3. Remove the default LPSPI3 peripheral and add
an `lpspi3` alias to LPSPI4.
Fixes#57942
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add missing USB-OTG control nodes. Like other STM32-platforms it's
disabled by default and uses the internal 48 MHz clock by default.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Add an API-less MFD driver for nPM6001. In this case, the MFD device
driver doesn't expose any API as plain I2C API is used within other
device drivers (regulator, GPIO, watchdog). This driver just initializes
some device properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Update the default Flash and SRAM size to 1024kb and 288kb, Update the
mpn file overrides accordingly
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
cpu@0 node is not supported on some mpn's so it should be deleted from
the mpn files and not the package files.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
- Remove the spi node from an older commit since its replaced with the
SCB node now
- GPIO nodes should have been part of pinctrl
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
include the infineon,cat1-scb.yaml for I2c and UART bindings to convey
that they are using SCB (Serial Control Block)
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Add a new regulator driver for Analog Devices ADP5360. While it is a MFD
device, only support for BUCK/BUCKBOOST regulators is added in this
patch.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add new vref node to the DTS definitions of supported SoCs.
Extend DTS ADC channel properties where missing.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Add VREF+ sensor driver and DT node definition.
This driver allows determining the actual voltage applied to an SoC's
VREF+ pin, by comparing the VREFINT internal bandgap voltage reference
with its factory calibration data.
In packages where VREF+ is bonded to VDDA, this permits direct measurement
of VDDA voltage.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
