Add I2C target driver used buffer mode. The maximum accessible buffer
is 2044 bytes, the default is 256 bytes.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add basic device tree description fro stm32wba soc series.
This includes Flash/RAM clocks and clock control nodes
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add support of r8a77961 SoC to gen3 series.
Create a dtsi file with a common part for both r8a77951 and r8a77961.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\xmc47_relax_kit board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Adding support for the adafruit can picowbell shield for the
raspberry pi picoi. Also added nodelable for spi0 called 'pico_spi'
as well as an GPIO nexus node 'pico_header'
Signed-off-by: Joseph Yates <joeyatessecond@gmail.com>
This change introduces the "_rtc_timer" suffix for the system tick timer
driver "compatible" property and aligns naming conventions with the
actual CC13/26xx SoC series product policy.
This frees up the "_rtc" namespace to introduce additional APIs based on
the same peripheral in the future (not part of this PR):
rtc: rtc@... {
compatible = "ti,cc13xx-cc26xx-rtc";
...
timer {
compatible = "ti,cc13xx-cc26xx-rtc-timer";
...
};
counter {
compatible = "ti,cc13xx-cc26xx-rtc-counter";
...
};
pps {
compatible = "ti,cc13xx-cc26xx-rtc-pps";
...
};
};
Or alternatively an MFD pattern with similar requirements.
Fixing the namespacing now makes sense standalone as it reduces the
chance of custom drivers being broken in the future.
Redundant extension of the mandatory system clock devicetree node is
replaced with a single `status = "okay"` which seems to be the more
sensible default to avoid user error when defining custom boards.
Knowledgeable users can still override this if really needed.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Removes duplicate code and inconsistencies in the naming of the
cc13xx_cc26xx devicetree and RTC driver hierarchy and alignes it with
the actual TI product series naming hierarchy.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Add SHA256 accelerator support for it8xxx2 series.
This driver passes the following test:
tests/crypto/crypto_hash/
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Changes rshunt-milliohms to rshunt-micro-ohms allowing for current
sensing of greater than 16.4A (1mOhm resistor). This is commonly
set to 100 uOhm for VMU/FMU boards/applications.
Co-authored-by: James Goppert <james.goppert@gmail.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
The different references manuals of the STM32H7 family (RM099, RM0433,
RM0445 and RM0468) states that SDMMC2RTS and STMMC2EN are on bit 9 of
respectively RCC_AHB2RSTR and RCC_AHB2ENR (not on bit 8). Fixes the stm32h7
dts accordingly.
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
Reuse existing MCUX-based shim driver for LPUART that is compatible with
the hardware block in S32K344. DMA is not yet supported.
Use the board's debug connector (P6 / LPUART2) as default console.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
SIUL2 may require multiple interrupt handlers instead of a single one as
currently supported for S32Z/E. This is needed to enable support on
S32K3.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Support pin control for NXP S32K3 devices and enable it by default on
mr_canhubk3 board configuration.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The clock controller is a singleton controller for all the system-level
clocks (XOSC, PLL, CGM, etc) to provide run-time information to the
peripheral device drivers about the module's clocks.
Clock configuration is not yet supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The S32K3 MCUs are 32-bit Arm Cortex-M7-based microcontrollers with a
focus on automotive and industrial applications. The S32K344 features
a lock-step core, internal flash, RAM and TCM with ECC.
Co-authored-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Co-authored-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add a small delay between reading the transport header and reading the
HCI data. Failing to do so on a nRF9160<->nRF52832 link was reliably
resulting in the nRF9160 trying to read data before the nRF52832 had
set up the SPI transaction, resulting in the host reading a buffer full
of 0x00 and having to run the entire read result again.
Transceiving a 10 byte packet takes at least 31uS, while 100 byte
packets are around 150uS (duration of `spi_transceive` call). Waiting
1 tick to eliminate the need for most retransmissions is a valid
tradeoff.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add an option that signifies that the ESP modem may be reset at the same
time as the SoC by an external source. When this is the case, we first
wait for an unsolicited "ready" message from the modem, before
attempting to reset the device. This prevents two initialisation
sequences attempting to run at the same time.
We still want to wait for the complete initialisation sequence to
complete before returning in this case.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This adds support for the TIMER1-4 counter.
Each counter has 24bits and can run on LP_CLK (15-32KHz)
or DIVN clock (32MHz) with prescaler 1-32.
Each counter can have one alarm set.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
The display controller supports software reset and the driver already
implements it. Therefore it's not necessary to require a reset gpio in
device tree.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Remove `clocks` property for fixed-clock binding.
A fixed-clock should not have an input clock, since by
definition it's an always on fixed-rate clock.
Signed-off-by: Moritz Fischer <moritzf@google.com>
This adds a driver for Texas Instruments Cost-Optimized, Ultra-Small,
12-Bit, System-Monitoring ADCs. Currently only TLA2021 is supported,
TLA2022 and TLA2024 may follow based on this driver.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Convert the XPT2046 driver to the input subsystem, change the api,
remove the callback and enable logic.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Usage of 64-bit address constants from devicetree without a
UINT64_C wrapping macro results in the following warning and the
cut-off of the address value:
"warning: integer constant is so large that it is unsigned"
This change extends devicetree API adding few wrappers over the
address constant getters which add ULL size suffix to an
address integer literal when the appearance of 64-bit address
values is possible
Signed-off-by: Alexander Razinkov <alexander.razinkov@syntacore.com>
Add a GPIO based quadrature decoder driver that reports relative axes
movements using the input subsystem.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Adds properties to configure OCTOSPI IO
Manager data lines. That allows to use
any `IOLowPort` and `IOHightPort`.
Note: OSPIM requires additional clock to be enabled.
Please refer to Reference Manual.
Extra clock can be enabled in devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Add Nuvoton numaker series UART support, including interrupt-driven,
also apply pinctrl and clock-control.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add Nuvoton numaker series clock controller support, including:
1. Do system clock initialization in z_arm_platform_init().
2. Support peripheral clock control API equivalent to BSP
CLK_EnableModuleClock()/CLK_SetModuleClock().
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add support for communication with serial ports on native POSIX platform
via UART driver API. Serial port driver supports polling API,
configuration of the serial ports used via devicetree and command line
options, and runtime configuration with `uart_configure`.
Multiple instances of the driver are supported.
Example use and configuration is also demonstrated in the
`samples/drivers/uart/native_tty` sample.
Closes: #56586
Signed-off-by: Marko Sagadin <marko.sagadin42@gmail.com>
Add simple mechanism to load the image from IMR memory. Basically we are
only setting a flag in power off for the next boot to jump to existing
image in IMR.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
The IS31FL3216A is a fun light LED controller. The LED current of each
channel can be set in 256 steps by adjusting the PWM duty cycle through
an I2C interface.
Signed-off-by: Guy Morand <guy.morand@bytesatwork.ch>
Add a minimal driver for the ti lp5569 led controller. The driver supports
multiple instances. Commands on|off|set_brightness are supported.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
Currently, only the presence of a GIC is reflected in the device tree,
and its version must be set separately in each SoC's Kconfig.
This patch adds separate bindings for each GIC version whose presence
in the device tree automatically enables the corresponding Kconfig symbol.
Signed-off-by: Piotr Wojnarowski <pwojnarowski@antmicro.com>
When the GIC driver was originally introduced, it was only used on
Cortex-R SoCs. However, this is not the case anymore. Update the
description to reflect that this driver is not specific to Cortex-R.
Signed-off-by: Piotr Wojnarowski <pwojnarowski@antmicro.com>
Add driver for TCN75A temperature sensor. The following features are
supported:
- TCN75A oneshot mode, which allows single shot conversions with lower
power consumtion
- Resolution selection, up to 12 bit resolution (9 bit default)
- Triggering based on temperatue thresholds. If the TCN75A exits a set
threshold range, the application can be notified via a callback.
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
Add a new pinctrl driver for TI CC32XX SoC. The driver has not been
tested, just implemented following datasheet specs and checked that it
compiles. Consider this as a best-effort driver to remove custom pinmux
code in board files.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This PR adds a custom driver for the ADS1112 ADCs. Unlike ADS1113/4/5
family served by the ADS1x1x driver, the ADS1112 does not use an address
pointer to address config registers. Instead, there is only one writable
register and all i2c writes will set it. The registers resemble the
ADS1119 device, but config bitmap is different, include a distinct data
rate table, gain table, and input multiplexing table. There is also not a
status register to be monitored with the ADS1112, as it uses config bit 7
for the same purpose instead of a separate register.
The driver was tested on hardware using the ADC shell interface. Manual
probing validated the voltages for the MUX_SINGLE configs at datarate 15
in CM_SINGLE. Higher gains were not tested and CM_CONTINUOUS is not
supported in this initial implementation.
The new driver has also been added to the existing ADC test using adc_emul
for completeness.
Origin: original
License: Apache 2.0
Purpose: Adding support for ADS1112 ADCs
Signed-off-by: Jordan Montgomery <jordan.montgomery@getcruise.com>
Move dt files related to SoC family and series to npcx folder. It only
leaves SoC dt file in `dts/arm/nuvoton folder` in case of confusion with
the other Nuvoton SoCs.
The dt files path will be:
dts/arm/nuvoton
|--npcx
| |--npcx7
| | |--npcx7-miwus-wui-map.dtsi
| | |--npcx7-alts-map.dtsi
| | |--.....
| +--npcx9
| | |--npcx9-miwus-wui-map.dtsi
| | |--npcx9-alts-map.dtsi
| | +--.....
| |--npcx-miwus-wui-map.dtsi
| |--npcx-alts-map.dtsi
| |--npcx.dtsi
| |--npcx7.dtsi
| |--npcx9.dtsi
|--npcx7m6fb.dtsi
|--npcx7m6fc.dtsi
|--npcx9m8f.dtsi
+--npcx9m3f.dtsi
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move the two UART nodes so that they are under "soc" rather than "espi",
leave only xec-espi-host-dev nodes there.
The UART device can be used indepdently by the driver uart_mchp_xec.c
and it's normally initialized before before the espi one.
Moving the device node up a level so this does not trigger a false
positive on the build time priority checking.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Restructure the Bosch M_CAN driver backend to use per-instance Message RAM
configuration.
This removes the need for a common, artificial "can" devicetree node for
SoCs with multiple Bosch M_CAN-based CAN controllers and allows for
per-instance configuration of the number of e.g. standard (11-bit) and
extended (29-bit) filter elements.
As part of the restructure, software handling of CAN filter flags was moved
from per-flags bitfields to per-filter bitfields, solving an issue when
using more than 32 standard (11-bit) filter elements or more than 16
extended (29-bit) filter elements.
Fixes: #42030, #53417
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN devicetree binding to use a bosch,mram-cfg property
for specifying the memory layout of the Bosch M_CAN Message RAM. This is
identical to the Linux kernel devicetree binding for Bosch M_CAN IP core
based CAN controllers.
This introduces an offset cell which can be used for controllers with
shared Message RAM between Bosch M_CAN instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The BG95 pin configuration does not internally ever use the reset pin.
Because of this, there is no need to make reset pin mandatory.
Commit removes reset pin dependency [e.g. in case of BG95].
Signed-off-by: Andrei Hutanu <andrei.hutanu.i@gmail.com>
Add a property to the ADC channels which allows the configuration
of the current source pin.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Added Input/Output trigger mux address's as properties
that can be passed into the DMA driver. This is intended
to send INPUTMUX signals into the DMA.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Ports the Jinghua Display JHD1313 LCD (with RGB backlight) driver
to use the new auxdisplay driver interface. This driver is used on
the seeed grove LCD RGB display, and replaces it.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
Removed few VIF properties which are being hardcoded
Updated the script to parse source VIF XML and add information to
the output
Added optional Kconfig option to configure custom source VIF XML path
Cleaned up the code
Signed-off-by: Madhurima Paruchuri <mparuchuri@google.com>
Added intel LPSS DMA interface using dw common to support
usage of internal DMA in LPSS UART, SPI and I2C for
transfer and receive operations.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds the pwrmgr devicetree node. This is a simple binding that holds
only the address of the registers for now.
This patch is part of the OpenTitan watchdog (AON Timer) support patch
series. It is needed to ensure that the watchdog reset functionality
is enabled.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
The OpenTitan power manager is responsible for changing the OpenTitan's
operation to and from low power state. This patch adds a simple binding
for the power manager's config registers.
This is part of the OpenTitan watchdog patch series. The power manager
HWIP block needs to be configured to enable the watchdog reset
functionality in the OpenTitan Verilator simulation.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
Adds the AON Timer device in the OpenTitan Earlgrey device tree.
Adds overlay files to enable the watchdog and set the alias to
`watchdog0`.
Adds the AON timer (watchdog part) to the supported features section
of the OpenTitan documentation.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
The OpenTitan AON Timer is a hardware device that has two features:
the wakeup timer and watchdog timer. This commit series implements the
watchdog feature.
The spec can be found here:
https://opentitan.org/book/hw/ip/aon_timer/index.html
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
Flash address is updated to 0x16000000, i.e. actual location instead of
remapped one. FLASH_BASE_ADDRESS is now set via dts.
Co-authored-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
This selects default flash controller in device tree.
Co-authored-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
This adds support for the USB interface for the
Renesas Smartbond DA1469x device family.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
RT1040 removes LPSPI3, and refers to the peripheral called LPSPI4 on
other RT devices as LPSPI3. Remove the default LPSPI3 peripheral and add
an `lpspi3` alias to LPSPI4.
Fixes#57942
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add missing USB-OTG control nodes. Like other STM32-platforms it's
disabled by default and uses the internal 48 MHz clock by default.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Add an API-less MFD driver for nPM6001. In this case, the MFD device
driver doesn't expose any API as plain I2C API is used within other
device drivers (regulator, GPIO, watchdog). This driver just initializes
some device properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Update the default Flash and SRAM size to 1024kb and 288kb, Update the
mpn file overrides accordingly
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
cpu@0 node is not supported on some mpn's so it should be deleted from
the mpn files and not the package files.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
- Remove the spi node from an older commit since its replaced with the
SCB node now
- GPIO nodes should have been part of pinctrl
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
include the infineon,cat1-scb.yaml for I2c and UART bindings to convey
that they are using SCB (Serial Control Block)
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Add a new regulator driver for Analog Devices ADP5360. While it is a MFD
device, only support for BUCK/BUCKBOOST regulators is added in this
patch.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add new vref node to the DTS definitions of supported SoCs.
Extend DTS ADC channel properties where missing.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Add VREF+ sensor driver and DT node definition.
This driver allows determining the actual voltage applied to an SoC's
VREF+ pin, by comparing the VREFINT internal bandgap voltage reference
with its factory calibration data.
In packages where VREF+ is bonded to VDDA, this permits direct measurement
of VDDA voltage.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Introduce DesignWare ARC Data Fusion IP Subsystem(DFSS) SPI
driver for ARC boards, i.e. EMSDP, which uses DW SPI to controll
SPI-Flash and DFSS SPI to connect external devices. Both drivers
share most source code, but DFSS uses ARC auxiliary registers.
Move FIFO depth setting to device tree.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
Add support board Pandora_STM32L475;
Drives that have been verified at present:
- GPIO
- PWM
- QSPI_FLASH_W25Q128
Signed-off-by: Tianshuang Ke <qinyun575@gmail.com>
Renesas Renesas SmartBond(tm) have two ADC blocks:
GPADC and SDADC.
This change adds drivers for both.
Each ADC supports only one channel setup, drivers allow
to have multiply channels in sequence. Switching
between ADC sources in done in software.
GPADC has 10 bit resolution (accuracy can be increase
with oversampling). Values up to 3.6V can be measured
on selected pins. V30 and VBAT1 can also be measured.
SDADC has 14 bit resolution and can take measurements
from 8 pins (single of differential) and VBAT.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Since Merge zephyrproject-rtos#57360, user can use ch<x> and ch<x>N
simultaneously, which is beneficial for STM32 users
working in motor control area.
Signed-off-by: Savent Gate <savent_gate@outlook.com>
Driver was based on can_sam. SAMC21 has only 1 interrupt for one
can "output", so can interrupt has to executes two lines of
interrupts.
CAN is configured to use OSC48M clock via GLCK7. GLCK7 is set
by divider configured from dts.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
- The boards\arm\cy8cproto_063_ble board now has ADC enabled
- This includes overlay files for the test app and sample app
Signed-off-by: Bill Waters <bill.waters@infineon.com>
This driver implement basic functions of ili9342c controller
which comes mostly with IPS displays.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
The LSM6DSV16X is a system-in-package featuring a 3-axis digital
accelerometer and a 3-axis digital gyroscope for industrial and IoT
solutions. The LSM6DSV16X embeds advanced dedicated features such as
a finite state machine (FSM) for configurable motion tracking and a
machine learning core (MLC) for context awareness.
https://www.st.com/en/mems-and-sensors/lsm6dsv16x.html
This driver is based on stmemsc HAL i/f v2.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert the NPCX keyboard scan driver to the input subsystem and add the
input to kscan compatibility driver to maintain functionality with the
current API.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a USB device controller driver skeleton to use as a starting point
for implementing a specific driver.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Example configuration uses 'A' and 'X' key codes for longpress events.
Described behavior shows correct key codes (30 and 45), however comments
near those key codes were invalid for 'X' key. Fix that.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Glitches were observed if a GPIO pin was configured by
ROM to a non-default state and then Zephyr PINCTRL
reconfigured the pin. The fix involves using the correct
PINCTRL YAML output enable and state flags. Reading the
current spin state and reflecting into new pin configuration
if the pin is output and the drive low/high properties are
not present. We also take advantage of GPIO hardware reflecing
the alternate output value in the parallel output bit before
enabling parallel output mode. Interpret boolean flags with
both enable and disable as do not touch if neither flag is
present. We give precedence to enable over disable if both
flags mistakenly appear. Note, PINCTRL always clears the
GPIO control input pad disable bit.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
The ACE 2.0 LNL platform has 5 HIFI4 cores. Change number
of cores to enable 5th core on the platform.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Added i-cache-line-size and d-cache-line-size values
to device tree for ace20_lnl platforms. These values
are used by sys_cache_instr_line_size_get and
sys_cache_data_line_size_get functions.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Allows Ethernet communication between "cells"
in the Jailhouse hypervisor.
The vring queue deviates from a standard virtqueue
so is implemented separately.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
This allows finding the correct PCIe device when multiple devices
have the same vendor-id/device-id but differ in the class-rev register
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
Add support for partial refresh profiles. This makes it possible to
use partial refresh on generation 2 devices which are able to store
partial refresh LUTs in OTP.
Partial refresh is only enabled if a partial profile has been
provided. The display will use the full refresh profile if in this
case.
Devices that need custom LUTs and voltages can specify them separately
for the full and partial profiles. The controller will be reset when
changing profiles which means that profiles always override the
default reset values. This means that it is, for example, possible to
use default values and LUTs from OTP for a full refresh and a custom
profile for partial refreshes.
For example, to use a GoodDisplay GDEY027T91 with partial refresh
simply use the following device tree fragment:
display: ssd1680@0 {
compatible = "solomon,ssd1680";
spi-max-frequency = <4000000>;
duplex = <SPI_HALF_DUPLEX>;
reg = <0>;
dc-gpios = <&arduino_header 15 GPIO_ACTIVE_LOW>;
reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>;
busy-gpios = <&arduino_header 13 GPIO_ACTIVE_HIGH>;
/* Enable the built-in temperature sensor */
tssv = <0x80>;
width = <264>;
height = <176>;
/* Enable partial refresh using built-in LUT */
partial {
};
};
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Update the device tree bindings for the SSD16xx driver to make it
possible to specify multiple refresh profiles.
The only profile currently supported is the 'full' profile.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The SSD16xx driver currently provides basic support for most chips in
the Solomon Systech SSD16xx range of e-paper drivers. We currently use
the SSD1608, SSD1673, SSD1675A, and SSD1681 in various boards
supported by Zephyr.
The main user-facing difference between the various SSD16xx chips is
the resolution they support (sources & gates), but there are other
differences as well. For example:
* 8 or 16 bits used to represent x coordinates
* 8 or 16 bits used to represent y coordinates
* Differences in refresh configuration (SSD16XX_CMD_UPDATE_CTRL2)
* Differences in LUT sizes
The driver currently assumes that the user specifies the number of
bits used to describe coordinates. However, as we add support for more
chips, more of the differences will become apparent and need
workaround.
Comparing data sheets from different chips in the SSD16xx range
suggests that there are (at least) two different generations
present. These differ in the size of the LUTs they expect and the way
they handle partial refresh. This impacts register layout where
SSD16XX_CMD_UPDATE_CTRL2 uses bit 3 selects "mode 2" whereas older
devices uses this for a mode referred to as "initial".
In order to add support for partial refresh in newer devices, we need
to be able to distinguish between the different generations of the
chip. It might be possible to add a DT property to indicate the
revision, but that seems like a bit of an anti-pattern and it would be
hard for users to specify the correct chip generation.
This change introduces chip-specific compatible strings instead of the
generic SSD16xx. There is unfortunately clear pattern that can be used
to distinguish different generations, so the full chip name must be
specified. A benefit of this is that we don't need to specify the
width of the fields describing coordinates in device trees.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add RT1040 SOC devicetree. This devicetree removes IP blocks absent on
the RT1040, and configures clock dividers correctly for the RT1040's
clock tree
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix PINT base address for LPC51xxx and 54xxx. These addresses were
incorrectly copied from the LPC55S69, which utilizes trustzone. Add the
relevant base address offset to the addresses.
Fixes#57334
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use the same wording in description for both I2C and SPI variants to
improve consistency.
Create st,lsm6dsl-common.yaml to include common binding properties from I2C
and SPI variants.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Update LTDC driver to use LCDIF bindings, to simplify bindings
between LCD interface controller IP blocks.
Boards supporting the LTDC are also updated to use the properties as
declared by the new lcd controller binding
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update MCUX ELCDIF driver to use new LCDIF bindings. This
update also adds support for configuring the root clock of
the ELCDIF module based on the pixel-clock property to the
RT11xx SOC clock init, as this SOC series has this IP block
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update DCNANO LCDIF IP to use shared lcd interface binding. This
requires changes to the RT5xx SOC and RT595 EVK, as this SOC
uses the LCDIF IP, and configures the clock for it based off
the new pixel-clock property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add common LCD interface binding. This binding captures the
following properties, which are shared between multiple LCD interface
IP blocks:
- VSYNC/HSYNC pulse width
- Vertical/Horizontal front and back porch
- HSYNC,VSYNC,data enable, and pixel clock polarity flags
- pixel clock frequency
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce phy-clock property, which is used by MIPI devices to determine
the target clock frequency for the MIPI PHY. This property can vary
depending on the attached display and target framerate.
Update the MIPI DSI MCUX driver to utilize this property to configure
the MIPI host, and update the RT500 clock initialization to configure
the MIPI root clock based on this property.
Remove dphy-clk-div property from the MIPI DSI 2L binding, as it
is redundant with this change.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Let the Bosch M_CAN front-end drivers supply their own register read/write
functions.
This is preparation for handling non-standard Bosch M_CAN register layouts
directly in the front-end and for accessing Bosch M_CAN IP cores over
peripheral busses.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Currently, the usb_dc_dw driver is not enabled for any platform.
Allow to build the driver for cyclonev_socdk. Subsequent patches
will allow the driver to be used on additional platforms.
Enable USB device controller and use use new snps,dwc2 compatible.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Although snps,designware-usb bindings already exist, this one is
prolematic. Compatible is too general and does not reflect
the actual controller IP. It has Zephyr-specific properties,
but has no zephyr prefix. It forces properties that are not
necessary for this controller. We start here with new bare minimum
properties for DesignWare OTG USB 2.0 controller.
The STM32F4 SoC family USB controllers, which are also implement
DesignWare OTG USB 2.0 IP, can also be used with existing drivers,
but require certain quirks. To use these we need special compatible.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add GDMA support for esp32s3.
Remove suspend/resume since they are optional and do
the same as start/stop.
Fix possible null pointer derreference.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Declare SCB nodes to be used as UART/SPI/I2C by the boards, Move
common declarations from psoc6_02 to the parent dtsi file
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Added device tree bindings and implementaion for setting the
spi controllers chip select setup and hold time settings.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
As recommended in AN4760 the memory region where the QSPI flash can be
memory mapped should be configured to be Strongly ordered memory. This
works around an issue where a speculative read from the CPU may cause
later problems with using the QSPI bus.
This avoids #57466.
Signed-off-by: Ole Morten Haaland <omh@icsys.no>
Most available AT45 flash chips have their first two sectors shorter
than the consecutive ones. Usually, the first sector is marked as 0a
and has its size equal to eight pages (one block) and the second one
(usually 0b) is the complement to the size of a regular sector.
This commits modifies the driver so that erasing of these first two
sectors is performed correctly. This modified behavior is configurable
with a new DT property so that it is still possible to also use legacy
AT45 chips that do not feature such sector split. Such legacy chips
usually also do not support the chip erase and sector erase commands,
so two more DT properties are introduced to cover that.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The LSM6DSO16IS is a system-in-package featuring a 3-axis digital
accelerometer and a 3-axis digital gyroscope for industrial and IoT
solutions. The LSM6DSO16IS embeds a new ST category of processing,
ISPU (intelligent sensor processing unit) to support real-time applications
that rely on sensor data. The ISPU is an ultra-low-power, high-performance
programmable core which can execute signal processing and AI algorithms
in the edge.
https://www.st.com/en/mems-and-sensors/lsm6dso16is.html
This driver is based on stmemsc HAL i/f v2.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enable UART on the DSP from the i.MX8MP target:
- add corresponding nodes in dtsi and dts;
- create a dts overlay for uart;
- add a config fragment for uart and console configuration.
So, in order to compile an application and enable UART
a user must run west build using DTC_OVERLAY_FILE and CONF_FILE.
Here's an example for hello_world:
west build -p always -b nxp_adsp_imx8m samples/hello_world/
-DDTC_OVERLAY_FILE="boards/xtensa/nxp_adsp_imx8m/
nxp_adsp_imx8m_uart.overlay" -DCONF_FILE="boards/xtensa/nxp_adsp_imx8m/
nxp_adsp_imx8m_uart.conf"
For other applications, like SOF, where we don't need UART, we simply run:
west build -p always -b nxp_adsp_imx8m ../modules/audio/sof/ --
-DTOOLCHAIN=/opt/zephyr-sdk-0.15.2/xtensa-nxp_imx8m_adsp_zephyr-elf/
bin/xtensa-nxp_imx8m_adsp_zephyr-elf -DINIT_CONFIG=imx8m_defconfig
The nxp_adsp_imx8m is using the nxp_imx_iuart driver.
For now, is used in poll mode.
Next step is to enable the interrupt controller in
DSP and use the interrupt driver UART.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
- Added initial version of Infineon CAT1 Flash driver
- Added binding file for infineon,cat1-flash-controller.yaml
- Added overlays for subsys/nvs and drivers/flash_shell
to support cy8cproto_063_ble, cy8cproto_062_4343w boards
- Defined erase-block-size in PSoC6 MPN dtsi.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
This PR adds a driver for the BMI323, which implements
the following features:
* Enable and disable accelerometer and gyroscope respectively
* Set full scale for accelerometer and gyroscope respectively
* Set data rate for accelerometer and gyroscope respectively
* Get samples (x,y,z) from accelerometer and gyroscope respectively
* Get die temperature
* Set trigger to accelerometer data ready, and accelerometer any motion.
The driver implements device and device runtime power management. If
runtime management is used, it is initialized into the suspended state,
which soft-resets the device to achieve the lowest possible power
consumption, otherwise it is resumed when initialized. When resumed,
the bus is initialized, the feature engine is enabled, and INT1 is
initialized.
The driver only implements the SPI bus at this time. The driver is
prepared to be expanded with I2C support in the future.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
Add the `full-duplex` property for the `microchip,enc28j60` node.
Replace ETH_ENC28J60_0_FULL_DUPLEX Kconfig option with this property.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Updated the code to to invoke reset using PCR block
z_mchp_xec_pcr_periph_reset() instead of resetting
using I2C Configuration register
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
The SERCOM4 is hardwired to PB30/31, PC18/19 internally for the LoRa
radio. Move the pinctrl entries to SoC dts level. The same applies for
samr35.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In general, peripherals should be disabled by default and enabled at
board level when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add the ability for the flash simulator to store its contents in a
memory region.
This allows filesystems on the flash simulator to survive a reboot.
And allows subsystems (e.g. coredump) to store their info on ram while
using the (existing) flash partition backend.
Add a example (for nucleo_f411re) that shows how to configure the flash
simulator for hardware (cfg discussion #54166).
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Add support for a generic NTC, `ntc-thermistor-generic`. In this case,
the compensation table is provided via devicetree. Note that DT property
is prefixed with `zephyr,`, because while hardware related, it is linked
to a particular software implementation.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactor driver to align a bit more with its Linux counterpart, ie,
ntc_thermistor. This driver did quite a few _unconventional_ things,
like using "zephyr," compatibles, a dedicated node for pre-computed
compensation table (referenced by the actual pseudo-device node), etc.
The comparison helper function should likely be simplified as well (to
avoid the need for custom wrapper for bsearch), but this can be done
later.
In this refactor, each thermistor gets a compatible, e.g. "epcos,xxxx".
Compatibles are known by the driver, so are compensation tables. This
simplifies devicetree files. There's no need to bother about
compensation tables in **every** board file if Zephyr supports a certain
NTC model.
In general we should respect Linux bindings, which in the end influence
how drivers are implemented. In this case, this principle resulted in
simplified, easier to use code.
For future developers, this is how support for a new NTC can be added:
1. Add to the end of the driver:
```c
#undef DT_DRV_COMPAT
#define DT_DRV_COMPAT vnd_model
static __unused const struct ntc_compensation comp_vnd_model[] = {
{ x, y },
...,
};
#define DT_INST_FOREACH_STATUS_OKAY_VARGS(NTC_THERMISTOR_DEV_INIT,
DT_DRV_COMPAT, comp_vnd_model)
```
3. In driver's Kconfig make sure it depends on
DT_HAS_$DT_DRV_COMPAT$_ENABLED
Note: $X$ means _value_ of X.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
It looks like the Zephyr thermistor driver bindings were half-copied
from Linux ntc-thermistor. Zephyr principle is to maintain compatibility
with Linux, when possible, so there's no reason to deviate here. Convert
the connection type from a custom enum to a boolean, as Linux does.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add Silicon Labs xG24-PK6010A (BRD4187C radio plug-in board)
support to the efr32_radio board.
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
This commit moves the `mpfs-icicle.dtsi` file to a common `microchip`
directory and updates include paths in the `mpfs_icicle` board
devicetree.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Initial sensor driver for NPM1300 PMIC charger.
Includes basic configuration of charger voltage and current.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
All Nucleo boards provide the ST Morpho connector/header, which exposes
all pins of the MCU. It is tipically used in ST shields, so provide a
nexus node to allow creating generic shields.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add Port 14/15 to device tree. These ports can only be configured as input.
Error out in gpio driver if user sets them as output.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
XMC4500 and XMC47/800 MCUs have a different memory layout. The
definitions have been moved to the derivative .dtsi of each MCU.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
This patch introduces support for NXP S32 CANEXCEL (CANXL) peripheral.
CAN protocol supporting:
- CAN classic
- CAN FD
Remote transmission request is not supported as this feature is not
available on NXP S32 CANXL HAL.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Added RTC driver that supports Motorola MC146818B
Enabled RTC set/get time and alarm, alarm callback
and update callback.
Counter and RTC uses same hardware in case of
Motorola MC146818, so they can't be used at a time.
Updated stand-alone mc146818 counter dts instances
to support rtc and counter with same compatible
string of "motorola,mc146818" on ia32, atom,
apollo_lake, elhart_lake and raptor_lake platforms.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
This patch adds support for the TI INA3221 current monitor.
This is the datasheet used for reference:
https://www.ti.com/lit/gpn/ina3221
Since this device has three channels, there is a custom attribute to
select which channel is to be used when getting a sample.
Measurements are done on all enabled channels.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Make it possible to use CPOL/CPHA SPI clock modes with the SDHC driver.
Some cards require the clock to switch to low when not active.
Signed-off-by: Łukasz Hejnak (LeHack) <lehack-ghub@lehack.pl>
The current configuration is too long and will block soc from
entering sleep mode. This change was made to get better power
number on EVB.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add a binding for STM32 ADC to specify the resolutions and all associated
register information (through a STM32_ADC_RES macro).
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
- Remove build asserts in favor of DT enums
- Remove power level property since it is unused by SDK
- Correct voltage ref value in DT to correspond to
chip specific values documented in reference manuals
instead of corresponding to SDK enum names.
- Fix SOC devicetrees affected by these changes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This is a new parameter to divide the LPTIM input clock
by a prescaler, changing the max reachable timeout of the LP timer.
It will divide the LPTIM input clock by 1 (reset value) up to 128.
The lptim configuration register is written with a 3bit value.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
CAVS platforms are not fully integrated with zephyr. Some of the
registers are still programed from SOF side. This feature can be enabled
for those platforms later when integration is fully done.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Implements a UART driver using PIO. Both PIOs are supported.
Only polling API is supported. Only 8N1 mode is supported.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Added a generic driver for RaspberryPi Pico PIO.
This driver is an intermediate driver for abstracting the PIO
device driver from physical pin configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
- To link image loadable by MCUboot, zephyr,code-partition
must be set in the DTS.
- Move partition definitions from SoC DTS to the board DTS.
- Remove scratch partition since MCUboot does not recommend to use it.
- Increase bootloader partitions to 48K to fit recent MCUboot.
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The newly added "power-amplifier-output" property for STM32WL SubGHz
radio nodes is mandatory.
Add the property to all affected modules and boards with the
appropriate value for the factory-default hardware configuration.
Add the "rfo-XX-max-power" properties to all affected modules and
boards with the appropriate value for the hardware configuration.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Add STM32WL-specific sx126x_set_tx_params function based on the
STM32CubeWL modifications to LoRaMac-node.
Add the "power-amplifier-output" DT property to
"st,stm32wl-subghz-radio" for selecting between the RFO_LP and RFO_HP
output configurations provided by the above mentioned function.
Add the "rfo-lp-max-power" and "rfo-hp-max-power" DT properties for
defining the maximum design power of the respective outputs' matching
networks.
closes#48511
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Adds a retention system which builds on top of retained_mem
drivers to allow partitioning of areas and data integrity with
magic header prefixes and checksum of stored data.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds address cells of size 1 and size cells of size 1 to GPREGRET
instances for Nordic devices.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This commit adds support for the `drivers.adc` test by adding an overlay
for the `efr32bg22_brd4184a` board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
EFR32MG24 uses the Secure Element's mailbox for entropy gathering
purposes. Reflect that in the device tree structure.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
- Add Gecko BURTC sys_clock driver to handle wake up from EM2,3 states
- Remove custom PM policy and dependency on HAL sl_power_manager service
- EM1 supported in all configurations
- EM2,3 supported only if SysTick is replaced by BURTC
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The efr32bg22-pinctrl.dtsi file was shared between bg22 and bg27 files.
It's better to name it efr32bg2x-pinctrl.dtsi.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
This commit splits device tree into more logical structure. Peripherals
which are on a board are in board dts files, while those which are parts of
a SoC are in SoC dtsi files.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
The general structure of efr32b27_sltb010a board is shared by more than one
board. This commit intrduces changes to the organization of board files,
which aim to take that into account.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
This commit makes the alarms-count dts property of the
rtc-device.yaml optional, setting the default to 0.
This simplifies the dts rtc dts node by not requiring
the property to be set to 0 if it is not supported.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
- Add initial version of Infineon CAT1 i2c driver.
- Add initial version of binding file for Infineon
CAT1 I2C driver
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
This adds the SPI driver for the Renesas SmartBond(tm) DA1469x MCU family.
The driver only supports controller mode. All four SPI modes are supported.
Note that the lowest supported speed is 2285714Hz.
Requesting speeds higher than 16MHz, will result in a 16MHz SCLK.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Move the devicetree bindings for Analog-to-Digital Converters (ADCs)
from dts/bindings/iio/adc to dts/bindings/adc as Zephyr does not have
an IIO layer.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
1. Increase sram to 256KB.
A block sram of SCAR0~15 is 4KB.
A block sram of SCAR16~19 is 16KB.
A block sram of SCAR20~23 is 32KB.
2. Removed the register of RVILMCR which has no effect.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The alternate pins of UART2 have been remapped, and the remapped
alternate pins must be added to the pinctrl map.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add the pinctrl node that has been remapped in the chip of it82xx2.
And modify kscan's pinctrl for the it82xx2.
And swap I2C default pins.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
On iMX.RT devices, the number of GPIO pins exceeds the maximum of
64 that the PINT interrupt controller can support. Therefore, two
interrupt lines are now shared between the GPIO modules.
This patch allows the user to set the interrupt source for a GPIO
peripheral. For most LPC devices, this will always be the PINT. For some
RT devices, the PINT cannot use pins on GPIO modules other than 0 and 1
as input, and thus the INTA and INTB sources should be used.
Since Zephyr does not support sharing these interrupt between all GPIO
controllers, the user must configure a subset of all GPIO controllers to
use the shared module interrupts. An example of how to do so is provided
for the RT595 EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce PINT driver, for NXP pin interrupt and pattern match engine.
The driver currently supports only the pin interrupt feature of the
PINT.
Add DTS entires for the PINT on LPC and RT devices that support this
peripheral, and remove the interrupt defintions that are PINT specific
from the GPIO module on these devices.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This patch adds HDA to device tree for LNL platforms.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The I2CLCTL_MLCS setting was recently added to MTL
platform. LNL has these registers in separate space, therefore
new field is added to intel,ssp-dai.yaml and appropraite definitions
to LNL device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Repleace usage of shim2 device tree field with hdamlssp.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In current implementation the HDAMLI2SL register is represented by
shim2 field in common SSP device tree file. This could be misleading
since the filed is is different location to I2S IP.
Adding separate device for this register following DMIC case.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A recent change added the stop-bits and data-bits to the base
uart-controller binding, meaning it's no longer required to
be added in the Altera specific binding.
This requires no further changes because its only use is in
uart_altera.c where only the index of the enum is used,
which remains the same between the new implementation and
how it was previously implemented in the altera specific binding.
Relevant commit: 0234f12
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
PR https://github.com/zephyrproject-rtos/zephyr/pull/55129 deleted the
"port-sel" property. Delete this property from remaining Microchip SoC
variants and boards.
Test: west build -b mec172xevb_assy6906 samples/drivers/espi/
Signed-off-by: Keith Short <keithshort@google.com>
The nRF9161 is technically a SiP (System-in-Package) that consists of
the nRF9120 SoC and additional components like PMIC, FEM, and XTAL,
so for nrfx/MDK the nRF9120 SoC is to be selected as the build target,
but since the nRF9161 is what a user can actually see on a board, using
only nRF9120 in the Zephyr build infrastructure might be confusing.
That's why in the top level of SoC definitions (for user-configurable
options in Kconfig, for example) the nRF9161 term is used and nRF9120
underneath.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add the header file required for the example to work. Users get the
following error due to unresolved INPUT_BTN_* values otherwise:
parse error: expected number or parenthesized expression
Signed-off-by: Amit Kucheria <amitk@kernel.org>
Signed-off-by: Amit Kucheria <amit@mbedrock.com>
These bindings are removed because they are now handled in the
included base uart-controller.yml.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Add bindings for LTC1665/LTC1660, which is a 8/10-bit
Digital-to-Analog Converter with eight individual channels.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
This addition should help users to better understand potential issues
with domain clock configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In ACE 2.0 platform (LNL) dmic got two new shim register ranges.
DMIC driver need to program them to configure the interface.
This patch adds new shims to device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
This adds USB-HS support for LPC55S16, much in the same way that
LPC55S28 support was added previously.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
The temperature sensor of the STM32F0x0 is similar to C0 (with one value
for calibration) but uses a negative coefficient, so we add it to the
bindings, just like in st,stm32-temp.yaml
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add a devicetree binding for the CAN-FD capable variant of the NXP FlexCAN
controller. Add example devicetree snippets to both NXP FlexCAN and NXP
FlexCAN-FD binding documentation to limit confusion.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the nxp,kinetis-flexcan devicetree compatible to nxp,flexcan as it
is not specific to the NXP Kinetis series.
This is preparation for adding a nxp,flexcan-fd binding.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add new compatible to separate production calibrated sensors
with single and dual calibration temperatures. Also update
stm32_temp driver to support single calibration sensors.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Adds support for a devicetree property that controls the ClockDiv
value provided to the SDIO during init.
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
No fmc node for the stm32u5 is implemented. This commit
adds a stm32-fmc compatible node to the device tree.
Signed-off-by: Christian Spinnler <christian.spinnler@fau.de>
Without adding a RAM entry for the USB RAM in the MPU,
USB RAM is mapped in the Peripheral Memory region
where unaligned memory accesses will cause a fault error.
Unaligned access errors were uncovered when we switch
to a different Zephyr C library where the memcpy function
implementation has unaligned accesses to the USB RAM.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Zephyr SPI driver model for full-duplex operation assumes
data will be transmitted and received during each clock period.
The QMSPI driver for the XEC family also supported dual and
quad I/O use cases which are inherently half-duplex. To
support dual/quad the driver incorrectly processed spi buffers
as all transmit buffers first then all receive buffers. This
worked if only the SPI driver was used. It did not work with
the Zephyr flash SPI NOR driver which assumes SPI drivers
follow the SPI driver model. This commit implements a QMSPI
driver that follows the Zephyr SPI driver model resulting in
a slightly smaller driver. Dual/quad SPI transactions are
supported if the experimental SPI extended mode Zephyr
configuration flag is enabled. We also remove the QMSPI full duplex
driver added previously to support the flash SPI NOR driver.
Added board to spi loop-back test and spi_flash sample.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add the FDCAN peripheral to the stm32H5 serie.
Two CAN1 & 2 instances for the stm32H56x/H57x devices.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Arm fvp_baser_aemv8r and fvp_base_revc_2xaemv8a boards are using
SMSC91C111 as their ethernet adapters.
Portions of the codes are based on FreeBSD code from its
'src/sys/dev/smc/if_smc.c' and 'src/sys/dev/smc/if_smcreg.h'.
This driver has two parts, one is the ethernet controller driver, which
is MAC layer driver. The other is the MDIO driver, which is the PHY
layer driver. Both of them are in the same source file due to that they
need to share the same reading and writing register functions and
the smsc object.
The mdio driver is needed by the existing 'phy_mii' driver, which is
a driver for the generic MII-compliant PHY.
This driver was developed under the fvp_base_revc_2xaemv8a target and
has been tested on the fvp_baser_aemv8r target.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
move DT_DRV_COMPAT to bmm150.h. so that can be decide which interface
to use.
define struct bmm150_bus_io interface for bmm150_i2c.c and bmm150_spi.c
in bmm150.h.
redefined bus operation interface in bmm150.c, this allow the driver
to decide which interface to use during construction.
Signed-off-by: Weiwei Guo <guoweiwei@syriusrobotics.com>
Convert the SDL driver to use the input subsystem. This is specifically
meant to emulate touchscreen drivers, so it's setup to send triplet of
x, y, touch for touch-on events and just touch off on touch off events.
Renamed the driver to input-sdl-touch since now we can also develop an
sdl driver for simulating key events.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This commit adds support for ANY_MOTION and DATA_READY interrupts for
the BMI270. To implement this, a different config blob than the
"max_fifo" blob has to be used.
Signed-off-by: Benjamin Lindqvist <benjamin@eub.se>
This adds the i2c driver for the Renesas SmartBond(tm) MCU family.
It supports blocking transfers and callback transfers.
Currently only supports controller mode.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
