Use clock control API to retrieve the module's frequency and
update the boards using it to provide the source clocks.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add phandle prop to reference any regulator that must
be enabled in order for the LPADC to function as intended.
Change LPADC driver to use this property if present.
LPADC on LPC55S36 depends on VREF peripheral, enable for this platform.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add node for VREF0 peripheral to LPC55S3X SOC DT
Clock VREF peripheral if status = okay in DT
Enable VREF on lpcxpresso55s36
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Enable clock control driver for NXP S32ZE SoCs and add clock sources
definitions for devicetree.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The ARM Cryptocell 310/312 IP is wrapped by Nordic specific registers.
It is organized as follows:
- Base address: Nordic wrapper
- Base address + 0x1000: ARM Cryptocell IP registers
Following more standard devicetree conventions, use a single node for
what is exposed as a single peripheral. The node contains 2 register
entries, one for the wrapper and a second one for the 3rd party IP.
Compatibles are used from more specific (nordic,cryptocell) to more
generic (arm,cryptocell-3xx).
Other minor fixes: peripheral is disabled by default (as it should be in
SoC dts files).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This platform (SOC_SERIES_EFM32PG1B) is also using SOC_GECKO_SERIES1 and
needs a pinctrl device defined to build the gecko-uart driver
successfully.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The gecko UART driver needs pinctrl support for SOC_GECKO_SERIES1
devices, this has been added to jg and pg 12b series in 40fa96506b but
is missing in others, causing some build failurse.
Add the device nodes for the gg11b and gg12b files since they contain
gecko-uart references and seems to be under the SERIES1 define.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This creates separate dtsi files for the various memory density codes of
SAM X2xfamilies (they are the same where the specific size exists.)
All of the boards with the exclusion of EV11L78A use the same density
model of 18 (32KiB RAM and 256KiB flash) which is what the samd2x.dtsi
include specified for all of them previously.
The density code has been confirmed being the same across the D20/D21,
C20/C21, L21, and R21 families. This does not carry over to some other
series such as the E5x.
Signed-off-by: Diego Elio Pettenò <flameeyes@meta.com>
Add SRAM code region definition to RT6xx series SOC. The RT6xx shares
SRAM partitions between the code and data bus, but a default allocation
is chosen by the SOC level devicetree. The user can modify this
allocation by changing the base address and size of the sram_code and
sram0 regions in their board devicetree.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add SRAM code region definition to RT5xx series SOC. The RT5xx shares
SRAM partitions between the code and data bus, but a default allocation
is chosen by the SOC level devicetree. The user can modify this
allocation by changing the base address and size of the sram_code and
sram0 regions in their board devicetree.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This is the final step in making the `zephyr,memory-attr` property
actually useful.
The problem with the current implementation is that `zephyr,memory-attr`
is an enum type, this is making very difficult to use that to actually
describe the memory capabilities. The solution proposed in this PR is to
use the `zephyr,memory-attr` property as an OR-ed bitmask of memory
attributes.
With the change proposed in this PR it is possible in the DeviceTree to
mark the memory regions with a bitmask of attributes by using the
`zephyr,memory-attr` property. This property and the related memory
region can then be retrieved at run-time by leveraging a provided helper
library or the usual DT helpers.
The set of general attributes that can be specified in the property are
defined and explained in
`include/zephyr/dt-bindings/memory-attr/memory-attr.h` (the list can be
extended when needed).
For example, to mark a memory region in the DeviceTree as volatile,
non-cacheable, out-of-order:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_VOLATILE |
DT_MEM_NON_CACHEABLE |
DT_MEM_OOO )>;
};
The `zephyr,memory-attr` property can also be used to set
architecture-specific custom attributes that can be interpreted at run
time. This is leveraged, among other things, to create MPU regions out
of DeviceTree defined memory regions on ARM, for example:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-region = "NOCACHE_REGION";
zephyr,memory-attr = <( DT_ARM_MPU(ATTR_MPU_RAM_NOCACHE) )>;
};
See `include/zephyr/dt-bindings/memory-attr/memory-attr-mpu.h` to see
how an architecture can define its own special memory attributes (in
this case ARM MPU).
The property can also be used to set custom software-specific
attributes. For example we can think of marking a memory region as
available to be used for memory allocation (not yet implemented):
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_NON_CACHEABLE |
DT_MEM_SW_ALLOCATABLE )>;
};
Or maybe we can leverage the property to specify some alignment
requirements for the region:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_CACHEABLE |
DT_MEM_SW_ALIGN(32) )>;
};
The conventional and recommended way to deal and manage with memory
regions marked with attributes is by using the provided `mem-attr`
helper library by enabling `CONFIG_MEM_ATTR` (or by using the usual DT
helpers).
When this option is enabled the list of memory regions and their
attributes are compiled in a user-accessible array and a set of
functions is made available that can be used to query, probe and act on
regions and attributes, see `include/zephyr/mem_mgmt/mem_attr.h`
Note that the `zephyr,memory-attr` property is only a descriptive
property of the capabilities of the associated memory region, but it
does not result in any actual setting for the memory to be set. The
user, code or subsystem willing to use this information to do some work
(for example creating an MPU region out of the property) must use either
the provided `mem-attr` library or the usual DeviceTree helpers to
perform the required work / setting.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This commit adds support for the ATMEL HSMCI peripheral
for the SAM4E MCU series, enabling native SD card support.
Signed-off-by: Vincent van Beveren <v.van.beveren@nikhef.nl>
While most of the ST family SoCs have the compatible string set, several
targets still miss it.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Add a MBOX driver wrapper around the NXP MU, simular to
the existing wrapper around the NXP S32 MRU. This allows Zephyr IPC
to work based on the MU, on a number of NXP boards.
Also update the SHA of NXP HAL to enable the Kconfig for this driver.
Signed-off-by: Yicheng Li <yichengli@google.com>
Remove `threshold-reg-offset` DT property and implement them with static
inline functions in `reg_def.h`
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add multi-device support in npcx adc driver since there is more than one
adc module in npcx4 series. And each adc's reference voltage might be
different, this CL introduces the `vref-mv` prop. to select its own
reference voltage.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Signed-off-by: Kate Yen <htyen@nuvoton.com>
Compat strings in SoCs allow tools to identify hardware described in
flattened device trees.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
This introduces PWM driver with supporting PWM output
APIs based on NXP S32 EMIOS peripheral. This supports
three mode: OPWFMB, OPWMCB and OPWMB.
OPWFMB uses internal counter, the new period and duty
cycle takes effect immediately.
OPWMCB and OPWMB use external counter as timebase, changing
PWM period at runtime will impact to all channels share the
same timebase. Also the new period and duty cycle take effect
in next period boundary of the timebase
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This PR adds a misc driver for NXP S32 eMIOS peripheral.
eMIOS provides multiple unified channels (UCs), there are
several channels can be used as reference timebase
(master bus) for other channels. At this time, the
driver does initialize global configuration for eMIOS
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Added devicetree and Kconfig for EFR32MG12P433F1024GM68, needed for
the BRD4170A radio board by Silicon Labs.
Signed-off-by: Warren Buffer <warren.buffer78@gmail.com>
Update SNVS pin names in RT11xx DTSI files to align with new pin data
generated for the RT1176 and RT1166 processors. This pin data is stored
within the NXP HAL, so the SHA of the HAL is also updated by this
commit.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Created a seperate device tree file for the stm32f765.
Moved common nodes from the stm32f767 device tree file to the new file and
based the stm32f767 off the stm32f765.
Signed-off-by: Rahul Arasikere <arasikere.rahul@gmail.com>
STM32L1, U5 and WBA can only have an asynchronous clock source for ADC.
STM32F2, F4 and F7 can only have a synchronous clock source for ADC.
For all these series, it can be defined directly in the dtsi files.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
This patch adds definitions for the nRF9131,
which is software-compatible with nRF9161.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
This commit changes the I2C instance to IOM.
IOM instance can be I2C or SPI. The choice of either
using I2C or SPI should be made in board DTS.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
This CL introduces new clock architectures in npcx4 series and wraps
clock configurations of different series by device tree files.
For example, the PWDWN_CTLx reg initialization relies on `pwdwn-ctl-val`
prop of pcc DT node now.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
/delete-node/ pointing at node labels needs to be out of the the tree
hierarchy, fixes the error:
devicetree error: zephyr/dts/arm/nordic/nrf52840_qfaa.dtsi:24 (column
16): parse error: expected node name
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This adds QSPI controller properties that allow tuning
chip select timings (needed for accessing QSPI at high speed)
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
RC32K/RCX/XTAL32K were present in device tree as fixed-clock.
Now calibration time for RCX and RC32K is added and settle time
for XTAL32K so additional binding is created.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
To better delimit renesas ranges dts, we need to use ranges folder.
It will also help maintainers to better delimit their files to
be notified about.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Since VWGPSM (Virtual Wire GPIO Target-to-Controller) registers are
introduced in npcx9 and later series, the CL moves the related DT nodes
from npcx-espi-vws-map.dtsi (Used for all npcx series) to the specific
dtsi files for npcx9 and npcx4 series.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Rename the base device-tree for the AM62x M4F from a SK EVM specific
to a more generic name since this DT describes the M4F subsystem in
the AM62x SoC.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The existing i2c sda/slc pinctrl nodes serve as an input and output
for the USIC. This limits the number of pins that can be used for i2c
since the pin must be internally connected to both DOUT0 and DX0 signals
on the USIC (for the sda signal for example).
It is also possible to use separate pins to DOUT0 and DX0, but connect
the pins externally. Add these extra pinctrl nodes and document their
use in infineon,xmc4xxx-i2c.yaml.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
In commit 541482ff20 the pinctrl alternate
function mask was increased to also include open-drain setting.
Revert this change because open-drain can already be set via property
drive-open-drain.
The commit also added separate pinctrl nodes for the i2c controller and
target modes. However, the alternate function settings
is the same in both modes, so keep only one and remove the mode
label.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Since the pwm_nrf_sw driver can now be used on all nRF SoCs, add its
corresponding DT node in the common file included by all those SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rename the STM32H7 FDCAN node labels to match to naming used in the ST
reference manuals. This also matches the naming used in the STM32H7 FDCAN
clock and pinctrl macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the STM32 FDCAN node labels to match to naming used in the ST
reference manuals. This also matches the naming used in the STM32 FDCAN
pinctrl macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the STM32 bxCAN driver DTS compatible, Kconfig symbol, and
implementation file to match the naming used in the ST reference manuals.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add ipm driver to use Inter Processor Interrupts
on Xilinx ZynqMP platform. This patch also adds sample
application that shows use of xlnx ipm driver.
This driver uses default arm gic interrupt controller
and works only for lockstep mode of cortex-r5f
cluster for now.
In split mode the cortex-r5 cluster will
have two r5f cores and they are expected to work in AMP
mode. If both r5f cores run simultaneouly, only one of
the core is able to receive IPI interrupts at this time
and it will be the one that started later. In future
this limitation shall be removed.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
This change introduces a new PWM driver for all CC13/26xx SoC.
See the documentation in ti,cc13xx-cc26xx-timer-pwm.yaml for detailed
usage instructions.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Enable CANFD for rt11xx by including nxp,flexcan-fd
compatibility for all CANFD capable CAN with associated
properties.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
This commit instantiates the counter peripheral.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Maciej Sobkowski <msobkowski@antmicro.com>
This commit addst support for the system timer peripheral which
can be found in Apollo4 SoCs.
Signed-off-by: Maciej Sobkowski <msobkowski@antmicro.com>
This device has a single instance of EMAC (a 100Mbps version of GMAC).
TCP/UDP checksum calculation is offloaded.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Make ethernet phys childs of the mdio device and move the mdio device up
a level on the tree. That makes the device hierarchy coherent with the
required initialization priority and allows keeping the sequence in
check with CHECK_INIT_PRIORITIES.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Reuse existing NXP LPSPI binding for this SoC since the hardware block
for this device is the same as the one supported for other NXP devices.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Update to shim driver compatible with the hardware block
in S32K344. Configure the pins before initializing I2C
to avoid happening bus busy.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Reuse existing MCUX-based shim driver for FlexCAN.
Enable flexcan0 for Zephyr canbus to run tests.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Devicetree specification v0.4, Section 2.3.1:
"The compatible string should consist only of lowercase letters, digits
and dashes, and should start with a letter."
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This state is never used in practice, even if handled by the PM
subsystem hooks. Shutdown-like states are always invoked manually, so
they don't need to be described in DT.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The `cpu-power-states` property needs to be defined at SoC dts files,
since it's a property of the SoC, not board.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 8 (CCU8)
module. There are two CCU8 nodes with each one having four slices.
Each slice has two output channels.
Unlike CCU4, this module can generate complementary high-side/low-side
signals for each output channel. A variable dead time can be added
during the off to on transitions to make sure that the
high-side/low-side signals are not on at the same time.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 4 (CCU4)
module. There are four CCU4 with each one having four channels
Thus it's possible to have up to 16 pwm output signals. The output of
each channel can only be connected to a specific port/pin. The possible
connection and gpio configurations are defined using pinctrl.
The CCU4 module also has a capture mode. Capture support will be added
in the future.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Add initial version of Infineon CAT1 counter driver
Add initial version of binding file for Infineon
Add counters to psco6 dtsi
Add external trigger pin that runs counter
Signed-off-by: Pavlo Havrylyuk <pavlo.havrylyuk@infineon.com>
CPU idle states are not board specific. This patch moves Nuvoton idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves NXP idle states
to the core SoC dts files. Board can always tweak some state parameters
(if needed), but the definition belongs to core SoC dts files, same as
e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves Microchip MEC
idle states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves TI idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
CPU idle states are not board specific. This patch moves STM32 idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Fixup support for DCS_LONG_WRITE command in DSI MCUX 2L driver. Since long
DCS commands may benefit from nonblocking I/O, add support for non blocking
transfers to the DSI driver.
This commit also corrects the interrupt number for the RT595, which uses
the DSI_MCUX_2L IP block.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added dts additions for stm32f105xb cpu which is the same as existing
stm32f105xc with less flash.
Signed-off-by: Mathieu Anquetin <mathieu.anquetin@groupe-cahors.com>
Add Nuvoton numaker series flash memory controller(FMC) with erase,
read & write features of soc-flash. Also update Nuvoton manifest
to include zephyrproject-rtos/hal_nuvoton#6.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
This CL attempts to implement npcx's flash driver instead of the
original one (npcx spi driver plus spi_nor flash driver).
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add a new pinctrl type to control peripheral modules' specific IO
characteristics such as tri-state, the power supply type selection (3.3V
or 1.8V), and so on. In NPCX series, the corresponding registers/fields
are irregular. This CL wraps these definitions to dt nodes and put them
in pinctrl property if needed.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add the new RCC bindings to the dtsi files.
STM32F373 uses the RCC F1 bindings because the ADC prescaler is the same
on the two series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Current erroneous usages of dma-channels prop by lpc-dma nodes:
* dma-channels devicetree property should describe the number of
channels supported by the dma controller, not the number of channels
in use.
* LPC55SXX and RTXXX SOCs should be setting dma channels prop at SOC
level, not board level, since it is an SOC property, not a board
property.
* lpc55s28 has 23 channels for dma0, not 20.
* lpc55s28 has 10 channels for dma1, not 0.
* lpc55s69 has 23 channels for dma0, not 20.
* rt5xx has 37 channels for dma1, not 0.
* rt6xx has 33 channels for dma0, not 20.
* rt6xx has 33 channels for dma1, not 0.
Fix all of these issues
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Set the DMA number of otrigs DT property at the SOC level instead of the
board DTS because it is an SOC property and does not change on different
boards.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add basic device tree description fro stm32wba soc series.
This includes Flash/RAM clocks and clock control nodes
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\xmc47_relax_kit board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
This change introduces the "_rtc_timer" suffix for the system tick timer
driver "compatible" property and aligns naming conventions with the
actual CC13/26xx SoC series product policy.
This frees up the "_rtc" namespace to introduce additional APIs based on
the same peripheral in the future (not part of this PR):
rtc: rtc@... {
compatible = "ti,cc13xx-cc26xx-rtc";
...
timer {
compatible = "ti,cc13xx-cc26xx-rtc-timer";
...
};
counter {
compatible = "ti,cc13xx-cc26xx-rtc-counter";
...
};
pps {
compatible = "ti,cc13xx-cc26xx-rtc-pps";
...
};
};
Or alternatively an MFD pattern with similar requirements.
Fixing the namespacing now makes sense standalone as it reduces the
chance of custom drivers being broken in the future.
Redundant extension of the mandatory system clock devicetree node is
replaced with a single `status = "okay"` which seems to be the more
sensible default to avoid user error when defining custom boards.
Knowledgeable users can still override this if really needed.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Removes duplicate code and inconsistencies in the naming of the
cc13xx_cc26xx devicetree and RTC driver hierarchy and alignes it with
the actual TI product series naming hierarchy.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The different references manuals of the STM32H7 family (RM099, RM0433,
RM0445 and RM0468) states that SDMMC2RTS and STMMC2EN are on bit 9 of
respectively RCC_AHB2RSTR and RCC_AHB2ENR (not on bit 8). Fixes the stm32h7
dts accordingly.
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
Reuse existing MCUX-based shim driver for LPUART that is compatible with
the hardware block in S32K344. DMA is not yet supported.
Use the board's debug connector (P6 / LPUART2) as default console.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Support pin control for NXP S32K3 devices and enable it by default on
mr_canhubk3 board configuration.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The S32K3 MCUs are 32-bit Arm Cortex-M7-based microcontrollers with a
focus on automotive and industrial applications. The S32K344 features
a lock-step core, internal flash, RAM and TCM with ECC.
Co-authored-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Co-authored-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
This adds support for the TIMER1-4 counter.
Each counter has 24bits and can run on LP_CLK (15-32KHz)
or DIVN clock (32MHz) with prescaler 1-32.
Each counter can have one alarm set.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Add Nuvoton numaker series UART support, including interrupt-driven,
also apply pinctrl and clock-control.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add Nuvoton numaker series clock controller support, including:
1. Do system clock initialization in z_arm_platform_init().
2. Support peripheral clock control API equivalent to BSP
CLK_EnableModuleClock()/CLK_SetModuleClock().
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add a new pinctrl driver for TI CC32XX SoC. The driver has not been
tested, just implemented following datasheet specs and checked that it
compiles. Consider this as a best-effort driver to remove custom pinmux
code in board files.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move dt files related to SoC family and series to npcx folder. It only
leaves SoC dt file in `dts/arm/nuvoton folder` in case of confusion with
the other Nuvoton SoCs.
The dt files path will be:
dts/arm/nuvoton
|--npcx
| |--npcx7
| | |--npcx7-miwus-wui-map.dtsi
| | |--npcx7-alts-map.dtsi
| | |--.....
| +--npcx9
| | |--npcx9-miwus-wui-map.dtsi
| | |--npcx9-alts-map.dtsi
| | +--.....
| |--npcx-miwus-wui-map.dtsi
| |--npcx-alts-map.dtsi
| |--npcx.dtsi
| |--npcx7.dtsi
| |--npcx9.dtsi
|--npcx7m6fb.dtsi
|--npcx7m6fc.dtsi
|--npcx9m8f.dtsi
+--npcx9m3f.dtsi
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move the two UART nodes so that they are under "soc" rather than "espi",
leave only xec-espi-host-dev nodes there.
The UART device can be used indepdently by the driver uart_mchp_xec.c
and it's normally initialized before before the espi one.
Moving the device node up a level so this does not trigger a false
positive on the build time priority checking.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Restructure the Bosch M_CAN driver backend to use per-instance Message RAM
configuration.
This removes the need for a common, artificial "can" devicetree node for
SoCs with multiple Bosch M_CAN-based CAN controllers and allows for
per-instance configuration of the number of e.g. standard (11-bit) and
extended (29-bit) filter elements.
As part of the restructure, software handling of CAN filter flags was moved
from per-flags bitfields to per-filter bitfields, solving an issue when
using more than 32 standard (11-bit) filter elements or more than 16
extended (29-bit) filter elements.
Fixes: #42030, #53417
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN devicetree binding to use a bosch,mram-cfg property
for specifying the memory layout of the Bosch M_CAN Message RAM. This is
identical to the Linux kernel devicetree binding for Bosch M_CAN IP core
based CAN controllers.
This introduces an offset cell which can be used for controllers with
shared Message RAM between Bosch M_CAN instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Added Input/Output trigger mux address's as properties
that can be passed into the DMA driver. This is intended
to send INPUTMUX signals into the DMA.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Flash address is updated to 0x16000000, i.e. actual location instead of
remapped one. FLASH_BASE_ADDRESS is now set via dts.
Co-authored-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
This selects default flash controller in device tree.
Co-authored-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
This adds support for the USB interface for the
Renesas Smartbond DA1469x device family.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
RT1040 removes LPSPI3, and refers to the peripheral called LPSPI4 on
other RT devices as LPSPI3. Remove the default LPSPI3 peripheral and add
an `lpspi3` alias to LPSPI4.
Fixes#57942
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add missing USB-OTG control nodes. Like other STM32-platforms it's
disabled by default and uses the internal 48 MHz clock by default.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Update the default Flash and SRAM size to 1024kb and 288kb, Update the
mpn file overrides accordingly
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
cpu@0 node is not supported on some mpn's so it should be deleted from
the mpn files and not the package files.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
- Remove the spi node from an older commit since its replaced with the
SCB node now
- GPIO nodes should have been part of pinctrl
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Add new vref node to the DTS definitions of supported SoCs.
Extend DTS ADC channel properties where missing.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Introduce DesignWare ARC Data Fusion IP Subsystem(DFSS) SPI
driver for ARC boards, i.e. EMSDP, which uses DW SPI to controll
SPI-Flash and DFSS SPI to connect external devices. Both drivers
share most source code, but DFSS uses ARC auxiliary registers.
Move FIFO depth setting to device tree.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
Add support board Pandora_STM32L475;
Drives that have been verified at present:
- GPIO
- PWM
- QSPI_FLASH_W25Q128
Signed-off-by: Tianshuang Ke <qinyun575@gmail.com>
Renesas Renesas SmartBond(tm) have two ADC blocks:
GPADC and SDADC.
This change adds drivers for both.
Each ADC supports only one channel setup, drivers allow
to have multiply channels in sequence. Switching
between ADC sources in done in software.
GPADC has 10 bit resolution (accuracy can be increase
with oversampling). Values up to 3.6V can be measured
on selected pins. V30 and VBAT1 can also be measured.
SDADC has 14 bit resolution and can take measurements
from 8 pins (single of differential) and VBAT.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
- The boards\arm\cy8cproto_063_ble board now has ADC enabled
- This includes overlay files for the test app and sample app
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Convert the NPCX keyboard scan driver to the input subsystem and add the
input to kscan compatibility driver to maintain functionality with the
current API.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add RT1040 SOC devicetree. This devicetree removes IP blocks absent on
the RT1040, and configures clock dividers correctly for the RT1040's
clock tree
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix PINT base address for LPC51xxx and 54xxx. These addresses were
incorrectly copied from the LPC55S69, which utilizes trustzone. Add the
relevant base address offset to the addresses.
Fixes#57334
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update LTDC driver to use LCDIF bindings, to simplify bindings
between LCD interface controller IP blocks.
Boards supporting the LTDC are also updated to use the properties as
declared by the new lcd controller binding
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Let the Bosch M_CAN front-end drivers supply their own register read/write
functions.
This is preparation for handling non-standard Bosch M_CAN register layouts
directly in the front-end and for accessing Bosch M_CAN IP cores over
peripheral busses.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Currently, the usb_dc_dw driver is not enabled for any platform.
Allow to build the driver for cyclonev_socdk. Subsequent patches
will allow the driver to be used on additional platforms.
Enable USB device controller and use use new snps,dwc2 compatible.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Declare SCB nodes to be used as UART/SPI/I2C by the boards, Move
common declarations from psoc6_02 to the parent dtsi file
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
As recommended in AN4760 the memory region where the QSPI flash can be
memory mapped should be configured to be Strongly ordered memory. This
works around an issue where a speculative read from the CPU may cause
later problems with using the QSPI bus.
This avoids #57466.
Signed-off-by: Ole Morten Haaland <omh@icsys.no>
- Added initial version of Infineon CAT1 Flash driver
- Added binding file for infineon,cat1-flash-controller.yaml
- Added overlays for subsys/nvs and drivers/flash_shell
to support cy8cproto_063_ble, cy8cproto_062_4343w boards
- Defined erase-block-size in PSoC6 MPN dtsi.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Updated the code to to invoke reset using PCR block
z_mchp_xec_pcr_periph_reset() instead of resetting
using I2C Configuration register
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
The SERCOM4 is hardwired to PB30/31, PC18/19 internally for the LoRa
radio. Move the pinctrl entries to SoC dts level. The same applies for
samr35.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In general, peripherals should be disabled by default and enabled at
board level when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add Silicon Labs xG24-PK6010A (BRD4187C radio plug-in board)
support to the efr32_radio board.
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
Add Port 14/15 to device tree. These ports can only be configured as input.
Error out in gpio driver if user sets them as output.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
XMC4500 and XMC47/800 MCUs have a different memory layout. The
definitions have been moved to the derivative .dtsi of each MCU.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
- Remove build asserts in favor of DT enums
- Remove power level property since it is unused by SDK
- Correct voltage ref value in DT to correspond to
chip specific values documented in reference manuals
instead of corresponding to SDK enum names.
- Fix SOC devicetrees affected by these changes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Added a generic driver for RaspberryPi Pico PIO.
This driver is an intermediate driver for abstracting the PIO
device driver from physical pin configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
- To link image loadable by MCUboot, zephyr,code-partition
must be set in the DTS.
- Move partition definitions from SoC DTS to the board DTS.
- Remove scratch partition since MCUboot does not recommend to use it.
- Increase bootloader partitions to 48K to fit recent MCUboot.
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The newly added "power-amplifier-output" property for STM32WL SubGHz
radio nodes is mandatory.
Add the property to all affected modules and boards with the
appropriate value for the factory-default hardware configuration.
Add the "rfo-XX-max-power" properties to all affected modules and
boards with the appropriate value for the hardware configuration.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Adds address cells of size 1 and size cells of size 1 to GPREGRET
instances for Nordic devices.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This commit adds support for the `drivers.adc` test by adding an overlay
for the `efr32bg22_brd4184a` board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
EFR32MG24 uses the Secure Element's mailbox for entropy gathering
purposes. Reflect that in the device tree structure.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
- Add Gecko BURTC sys_clock driver to handle wake up from EM2,3 states
- Remove custom PM policy and dependency on HAL sl_power_manager service
- EM1 supported in all configurations
- EM2,3 supported only if SysTick is replaced by BURTC
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The efr32bg22-pinctrl.dtsi file was shared between bg22 and bg27 files.
It's better to name it efr32bg2x-pinctrl.dtsi.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
This commit splits device tree into more logical structure. Peripherals
which are on a board are in board dts files, while those which are parts of
a SoC are in SoC dtsi files.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
The general structure of efr32b27_sltb010a board is shared by more than one
board. This commit intrduces changes to the organization of board files,
which aim to take that into account.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
- Add initial version of Infineon CAT1 i2c driver.
- Add initial version of binding file for Infineon
CAT1 I2C driver
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
This adds the SPI driver for the Renesas SmartBond(tm) DA1469x MCU family.
The driver only supports controller mode. All four SPI modes are supported.
Note that the lowest supported speed is 2285714Hz.
Requesting speeds higher than 16MHz, will result in a 16MHz SCLK.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
On iMX.RT devices, the number of GPIO pins exceeds the maximum of
64 that the PINT interrupt controller can support. Therefore, two
interrupt lines are now shared between the GPIO modules.
This patch allows the user to set the interrupt source for a GPIO
peripheral. For most LPC devices, this will always be the PINT. For some
RT devices, the PINT cannot use pins on GPIO modules other than 0 and 1
as input, and thus the INTA and INTB sources should be used.
Since Zephyr does not support sharing these interrupt between all GPIO
controllers, the user must configure a subset of all GPIO controllers to
use the shared module interrupts. An example of how to do so is provided
for the RT595 EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce PINT driver, for NXP pin interrupt and pattern match engine.
The driver currently supports only the pin interrupt feature of the
PINT.
Add DTS entires for the PINT on LPC and RT devices that support this
peripheral, and remove the interrupt defintions that are PINT specific
from the GPIO module on these devices.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
PR https://github.com/zephyrproject-rtos/zephyr/pull/55129 deleted the
"port-sel" property. Delete this property from remaining Microchip SoC
variants and boards.
Test: west build -b mec172xevb_assy6906 samples/drivers/espi/
Signed-off-by: Keith Short <keithshort@google.com>
The nRF9161 is technically a SiP (System-in-Package) that consists of
the nRF9120 SoC and additional components like PMIC, FEM, and XTAL,
so for nrfx/MDK the nRF9120 SoC is to be selected as the build target,
but since the nRF9161 is what a user can actually see on a board, using
only nRF9120 in the Zephyr build infrastructure might be confusing.
That's why in the top level of SoC definitions (for user-configurable
options in Kconfig, for example) the nRF9161 term is used and nRF9120
underneath.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This adds USB-HS support for LPC55S16, much in the same way that
LPC55S28 support was added previously.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Rename the nxp,kinetis-flexcan devicetree compatible to nxp,flexcan as it
is not specific to the NXP Kinetis series.
This is preparation for adding a nxp,flexcan-fd binding.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
No fmc node for the stm32u5 is implemented. This commit
adds a stm32-fmc compatible node to the device tree.
Signed-off-by: Christian Spinnler <christian.spinnler@fau.de>
Without adding a RAM entry for the USB RAM in the MPU,
USB RAM is mapped in the Peripheral Memory region
where unaligned memory accesses will cause a fault error.
Unaligned access errors were uncovered when we switch
to a different Zephyr C library where the memcpy function
implementation has unaligned accesses to the USB RAM.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Zephyr SPI driver model for full-duplex operation assumes
data will be transmitted and received during each clock period.
The QMSPI driver for the XEC family also supported dual and
quad I/O use cases which are inherently half-duplex. To
support dual/quad the driver incorrectly processed spi buffers
as all transmit buffers first then all receive buffers. This
worked if only the SPI driver was used. It did not work with
the Zephyr flash SPI NOR driver which assumes SPI drivers
follow the SPI driver model. This commit implements a QMSPI
driver that follows the Zephyr SPI driver model resulting in
a slightly smaller driver. Dual/quad SPI transactions are
supported if the experimental SPI extended mode Zephyr
configuration flag is enabled. We also remove the QMSPI full duplex
driver added previously to support the flash SPI NOR driver.
Added board to spi loop-back test and spi_flash sample.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add the FDCAN peripheral to the stm32H5 serie.
Two CAN1 & 2 instances for the stm32H56x/H57x devices.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the i2c driver for the Renesas SmartBond(tm) MCU family.
It supports blocking transfers and callback transfers.
Currently only supports controller mode.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Removed extra #includes at top of files. Missed closing } of
mec172xnlj.dtsi. Lower-cased 'reg' field of PWMs.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Adds the nodes for the GPDMA 1 & 2 peripherals
to the stm32h5 serie.
Each instance has 8 channels and 140 DMA requests.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The sdmmc clock source is either pll1_q or pll2_r according to the
refMan of the stm32h7 devices. HSI48 is not a vaild clock source.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fixes warnings produced by dtc 1.6 due to missing address-cell
in all arm st exti definition.
Signed-off-by: Christian Spinnler <christian.spinnler@fau.de>
Adds the nodes for the window and independent watchdog peripherals
plus the rng to the stm32h5 serie
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The number of available EasyDMA MAXCNT bits is now defined per-instance
in Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Change device tree VW routing to a form allowing overrides.
Add two new DT optional properties for specifying the reset
source and reset value of each virtual wire. Only virtual
wires that are enabled using the status property are modified.
NOTE: eSPI virtual wires are controlled in groups of 4 by
hardware. The optional reset signal source properties applies
to all four virtual wires in the group. If this field is
changed from the hardware default, it should be changed for
only one virtual wire in the group. If the property exists
in more than one wire in the group it must be set to the
same value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Modify Mircrochip MEC172x eSPI driver to get eSPI virtual wire
hardware routing from device tree.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The clock control driver requires three pieces of information:
PCR register index, bit position, and clock domain. Clock domain
was missing from DT information and MCHP macros.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Deleted adc_mchp_xec.c and microchip,xec-adc.yaml file.
DTSI, yaml, CMakeLists.txt and Kconfig.xec files are
updated for compatible.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Updated the "adc_mchp_xec_v2.c" adc driver to support both MEC172x and
MEC15xx SOC.
ADC smapling clock configuration updated using DTS.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
